2000 Mitsubishi Eclipse GS, StandardFACTORY OEM SERVICE PROCEDURE

Diagnostic Trouble Code Definitions: Notes

When Diagnostic Trouble Code (DTC) is obtained, refer to appropriate DTC test procedure in appropriate SELF-DIAGNOSTICS article.

NOTE: DTCs can only be retrieved by using a scan tool. See ENTERING ON-BOARD DIAGNOSTICS  .
DTC INDEX

Generic Scan Tool DTC (1) Description
- ECM/PCM Malfunction
P0100 VAF Circuit Malfunction
P0105 BARO Circuit Malfunction
P0105 (2) MAP Circuit Malfunction
P0110 IAT Circuit Malfunction
P0115 ECT Circuit Malfunction
P0120 TPS Circuit Malfunction
P0125 (3)(4)(5)(6) Excessive Time To Enter Closed Loop Fuel Control
P0128 Coolant Thermostat Malfunction
P0130 O2 Sensor Circuit Malfunction (Bank 1 Sensor 1)
P0135 O2 Sensor Heater Circuit Malfunction (Bank 1 Sensor 1)
P0136 O2 Sensor Circuit Malfunction (Bank 1 Sensor 2)
P0141 O2 Sensor Heater Circuit Malfunction (Bank 1 Sensor 2)
P0150 O2 Sensor Circuit Malfunction (Bank 2 Sensor 1)
P0155 O2 Sensor Heater Circuit Malfunction (Bank 2 Sensor 1)
P0156 O2 Sensor Circuit Malfunction (Bank 2 Sensor 2)
P0161 O2 Sensor Heater Circuit Malfunction (Bank 2 Sensor 2)
P0170 Fuel Trim Malfunction (Bank 1)
P0173 Fuel Trim Malfunction (Bank 2)
P0180 Fuel Temperature Sensor Circuit Malfunction
P0201 Injector No. 1 Circuit Malfunction
P0202 Injector No. 2 Circuit Malfunction
P0203 Injector No. 3 Circuit Malfunction
P0204 Injector No. 4 Circuit Malfunction
P0205 Injector No. 5 Circuit Malfunction
P0206 Injector No. 6 Circuit Malfunction
P0300 (3)(6) Random Misfire Detected
P0301 (3)(6) Cylinder No. 1 Misfire Detected
P0302 (3)(6) Cylinder No. 2 Misfire Detected
P0303 (3)(6) Cylinder No. 3 Misfire Detected
P0304 (3)(6) Cylinder No. 4 Misfire Detected
P0305 (3) Cylinder No. 5 Misfire Detected
P0306 (3) Cylinder No. 6 Misfire Detected
P0335 CKP Sensor Circuit Malfunction
P0340 CMP Sensor Circuit Malfunction
P0400 EGR Flow Malfunction
P0403 EGR Solenoid Malfunction
P0420 Catalyst Efficiency Below Threshold
P0421 Warm Up Catalyst Efficiency Below Threshold
P0431 Warm Up Catalyst Efficiency Below Threshold
P0442 EVAP System Leak Detected
P0443 EVAP Purge Solenoid Circuit Malfunction
P0446 EVAP System Vent Control Malfunction
P0450 EVAP System Pressure Sensor Malfunction Or Blocked System
P0455 EVAP System Leak Or Blockage Detected
P0460 Fuel Level Sensor Circuit Malfunction
P0500 Vehicle Speed Sensor Malfunction
P0505 Idle Control System Malfunction
P0510 Closed Throttle Position Switch Malfunction
P0551 Power Steering Pressure Sensor Circuit Range/Performance
P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input)
P0710 Transmission Fluid Temperature Sensor Circuit Malfunction
P0715 (5) Input/Turbine Speed Sensor Malfunction
P0720 (5) Output Speed Sensor Circuit Malfunction
P0725 (5) Engine Speed Input Circuit Malfunction
P0740 (5) Torque Converter Clutch System Malfunction
P0750 (5) Shift Solenoid "A" Malfunction
P0755 (5) Shift Solenoid "B" Malfunction
P0760 (5) Shift Solenoid "C" Malfunction
P0765 (5) Shift Solenoid "D" Malfunction
P1400 Manifold Differential Pressure Sensor Circuit Malfunction
P1500 Generator FR Terminal Circuit Malfunction
P1600 Serial Communication Link Malfunction
P1610 Immobilizer System Malfunction
P1715 Pulse Generator Assembly Malfunction
P1720 VSS Signal Line Malfunction
P1750 Solenoid Assembly Malfunction
P1751 (5) A/T Control Relay Malfunction
P1791 ECT Level Input Circuit To TCM Malfunction
P1795 Throttle Position Input Circuit Malfunction
(1) All DTCs use two-trip fault detection logic unless otherwise specified. If DTC is for a fault that may affect emissions, MIL will also illuminate.
(2) Applies to 1.5L only.
(3) On Diamante and Montero vehicles, this DTC will set on first trip fault is detected.
(4) On Eclipse, Galant 3.0L and Montero Sport vehicles, this DTC will set on first trip fault is detected.
(5) On Galant 2.4L vehicles, this DTC will set on first trip fault is detected.
(6) On Mirage vehicles, this DTC will set on first trip fault is detected.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.

Rather have a pro handle this?

A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.

Comes to youSame-day available12-month warranty
Get a Free Quote

No obligation. See pricing before you book.