Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
1999 Mitsubishi MonteroFACTORY OEM SERVICE PROCEDURE
Engine Performance DTCS
ENGINE PERFORMANCE DIAGNOSTIC TROUBLE CODE (DTC) LIST
| DTC | Description | ||||
|---|---|---|---|---|---|
| P0100 | Volume Airflow Circuit Malfunction | ||||
| P0105 | BARO Circuit Malfunction | ||||
| P0110 | IAT Circuit Malfunction | ||||
| P0115 | ECT Circuit Malfunction | ||||
| P0120 | TPS Circuit Malfunction | ||||
| P0125 | Excessive Time To Enter Closed Loop Fuel Control | ||||
| P0130 | O2 Sensor Circuit Malfunction (Bank 1 Sensor 1) | ||||
| P0135 | O2 Sensor Heater Circuit Malfunction (Bank 1 Sensor 1) | ||||
| P0136 | O2 Sensor Circuit Malfunction (Bank 1 Sensor 2) | ||||
| P0141 | O2 Sensor Heater Circuit Malfunction (Bank 1 Sensor 2) | ||||
| P0150 | O2 Sensor Circuit Malfunction (Bank 2 Sensor 1) | ||||
| P0155 | O2 Sensor Heater Circuit Malfunction (Bank 2 Sensor 1) | ||||
| P0156 | O2 Sensor Circuit Malfunction (Bank 2 Sensor 2) | ||||
| P0161 | O2 Sensor Heater Circuit Malfunction (Bank 2 Sensor 2) | ||||
| P0170 | Fuel Trim Malfunction (Bank 1) | ||||
| P0173 | Fuel Trim Malfunction (Bank 2) | ||||
| P0201 | Injector No. 1 Circuit Malfunction | ||||
| P0202 | Injector No. 2 Circuit Malfunction | ||||
| P0203 | Injector No. 3 Circuit Malfunction | ||||
| P0204 | Injector No. 4 Circuit Malfunction | ||||
| P0205 | Injector No. 5 Circuit Malfunction | ||||
| P0206 | Injector No. 6 Circuit Malfunction | ||||
| P0300 | Random Misfire Detected | ||||
| P0301 | Cylinder No. 1 Misfire Detected | ||||
| P0302 | Cylinder No. 2 Misfire Detected | ||||
| P0303 | Cylinder No. 3 Misfire Detected | ||||
| P0304 | Cylinder No. 4 Misfire Detected | ||||
| P0305 | Cylinder No. 5 Misfire Detected | ||||
| P0306 | Cylinder No. 6 Misfire Detected | ||||
| P0325 | Knock Sensor Circuit Malfunction | ||||
| P0335 | CKP Sensor Circuit Malfunction | ||||
| P0340 | CMP Sensor Circuit Malfunction | ||||
| P0400 | EGR Flow Malfunction | ||||
| P0403 | EGR Solenoid Malfunction | ||||
| P0420(1) | Catalyst Efficiency Below Threshold | ||||
| P0421(2) | Warm Up Catalyst Efficiency Below Threshold (Bank 1) | ||||
| P0431(2) | Warm Up Catalyst Efficiency Below Threshold (Bank 2) | ||||
| P0442 | EVAP System Leak Detected | ||||
| P0443 | EVAP Purge Control Valve Circuit Malfunction | ||||
| P0446 | EVAP System Vent Control Malfunction | ||||
| P0450 | EVAP System Pressure Sensor Malfunction Or Blocked System | ||||
| P0455 | EVAP System Leak Or Blockage Detected | ||||
| P0500 | Vehicle Speed Sensor (VSS) Circuit Malfunction | ||||
| P0505 | Idle Control System Malfunction | ||||
| P0510 | Closed Throttle Position Switch Malfunction | ||||
| P0551 | Power Steering Pressure Sensor Circuit Range/Performance | ||||
| P0705 | Transaxle Range Sensor Circuit Malfunction (PRNDL Input) | ||||
| P1103 | Turbocharger Waste Gate Actuator Malfunction | ||||
| P1104 | Turbocharger Waste Gate Solenoid Malfunction | ||||
| P1105 | Fuel Pressure Solenoid Malfunction | ||||
| P1400 | Manifold Differential Pressure Sensor Circuit Malfunction | ||||
| P1600 | Serial Communication Link Malfunction | ||||
| P1715 | Pulse Generator Malfunction | ||||
| P1750 | Solenoid Malfunction | ||||
| P1791 | ECT Level Input Circuit To TCM Malfunction | ||||
|
|||||
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
