Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
1999 Mitsubishi MonteroFACTORY OEM SERVICE PROCEDURE
Fuel Injectors
- Listen to injectors during cranking and at idle. They should make ticking sound. Frequency of sound should increase as engine speed increases.
- Except where noted, disconnect injector connector at injector. Check resistance between injector terminals. See INJECTOR RESISTANCES table. For testing rear bank injectors on 3000GT, disconnect rear bank connector. Check resistance between terminals indicated in 3000GT REAR BANK INJECTOR CHECK table. For testing right bank injectors on Galant 3.0L, disconnect intermediate connector. Check resistance between terminals indicated in GALANT RIGHT BANK INJECTOR CHECK table. For testing Montero 3.5L or Montero Sport 3.0L & 3.5L injectors, disconnect intermediate connector. Check resistance between intermediate connector terminals indicated in MONTERO SPORT 3.0L & 3.5L INJECTOR CHECK table.
INJECTOR RESISTANCES
| Application | Injector Resistance - Ohms @ 68°F (20°C) | |
|---|---|---|
| Eclipse | ||
| 2.0L Non-Turbo | 11-15 | |
| 2.0L Turbo | 2-3 | |
| 2.4L | 13-16 | |
| 3000GT | ||
| 3.0L Non-Turbo | 13-16 | |
| 3.0L Turbo | 2-3 | |
| All Except Eclipse & 3000GT | 13-16 | |
3000GT REAR BANK INJECTOR CHECK
| Injector No. | Check Between Intermediate Connector Terminals No. | |
|---|---|---|
| SOHC | ||
| 2 | 1 & 2 | |
| 4 | 1 & 5 | |
| 6 | 1 & 6 | |
| DOHC | ||
| 2 | 1 & 2 | |
| 4 | 1 & 3 | |
| 6 | 1 & 4 | |
| DOHC Turbo | ||
| 2 | 1 & 4 | |
| 4 | 2 & 5 | |
| 6 | 3 & 6 | |
GALANT RIGHT BANK INJECTOR CHECK
| Injector No. | Check Between Intermediate Connector Terminals No. |
|---|---|
| 1 | 1 & 2 |
| 3 | 1 & 3 |
| 5 | 1 & 4 |
MONTERO & MONTERO SPORT 3.0L & 3.5L INJECTOR CHECK
| Injector No. | Check Between Intermediate Connector Terminals No. |
|---|---|
| 1 | 8 & 3 |
| 2 | 8 & 2 |
| 3 | 8 & 1 |
| 4 | 8 & 7 |
| 5 | 8 & 6 |
| 6 | 8 & 5 |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
