1994 Mitsubishi Eclipse GSX, AutomaticFACTORY OEM SERVICE PROCEDURE

External Pages

's manual. Be very cautious using repair info from here because these pages may not apply to your vehicle. Different car Section 1 (Engine Controls - Specifications) Section 2 (Engine Controls - Adjustments) Section 3 (Engine Controls - System/Component Tests) Section 4 (Engine Controls - Tests W/Codes) Section 5 (Wiring Diagrams) Section 6 (Engine Controls - Basic Testing) Section 7 (Vacuum Diagrams) Section 8 (Engine Controls - Tests W/O Codes) Section 9 (Engine Controls - Remove/Install/Overhaul) Section 10 (Engine Controls - Pin Voltage Charts) Section 11 (3.0L V6 - VINS [H,J,K]) Section 12 (Suspension - Electronic) Section 13 (Axle Shafts - Front) Section 14 (Axle Shafts - Front) Section 15 (Axle Shafts - Front) Section 16 (Suspension - Front (Fwd)) Section 17 (Suspension - Electronic) Section 18 (Wheel Alignment Specifications & Procedures) Section 19 (Suspension - Rear (AWD & Fwd)) Section 20 (Axle Shafts - Front) Section 21 (Drive Axle - Rear) Section 22 (Drive Shaft & Universal Joints - AWD Models) Section 23 (Drive Axle - Rear Integral) Section 24 (Intake And Exhaust - Lancer Evolution) Section 25 (Mechanical - Lancer Evolution) Section 26 (General (Electrical) -- Lancer Evolution) Section 27 (Cooling - Lancer Evolution) Section 28 (General -- Lancer Evolution) Section 29 (Supplemental Restraint System (SRS) -- Lancer Evolution) Section 30 (Active Skid Control System (ASC) - Lancer Evolution) Section 31 (Manual Transaxle On-Vehicle Service - Lancer Evolution) Section 32 (Twin Clutch SST - Lancer Evolution) Section 33 (Lubrication - Lancer Evolution) Section 34 (Exterior - Lancer Evolution) Section 35 (Emission Control - Lancer Evolution) Section 36 (Keyless Operation System (Kos) - Lancer Evolution) Section 37 (Wireless Control Module (WCM) - Lancer Evolution) Section 38 (Ignition System - Lancer Evolution) Section 39 (Steering -- Lancer Evolution) Section 40 (Controller Area Network (Can) - Lancer Evolution) Section 41 (Clutch On-Vehicle Service - Lancer Evolution) Section 42 (Heater, Air Conditioning And Ventilation - Lancer Evolution) Section 43 (Interior - Lancer Evolution) Section 44 (Fuel Supply - Lancer Evolution) Section 45 (Rear Axle - Lancer Evolution) Section 46 (Basic Brake System - Lancer Evolution) Section 47 (Front Axle - Lancer Evolution) Section 48 (Charging System - Lancer Evolution) Section 49 (Clutch Overhaul - Lancer Evolution) Section 50 (Manual Transaxle Overhaul - Lancer Evolution) Section 51 (Parking Brakes - Lancer Evolution) Section 52 (Body - Lancer Evolution) Section 53 (Rear Suspension & Wheel Alignment - Lancer Evolution) Section 54 (Wheel And Tire - Lancer Evolution) Section 55 (Front Suspension & Wheel Alignment- Lancer Evolution) Section 56 (Local Interconnect Network (Lin) - Lancer Evolution) Section 57 (MULTIPORT Fuel Injection (MFI) (1 Of 6) - Lancer Evolution) Section 58 (MULTIPORT Fuel Injection (MFI) (2 Of 6) - Lancer Evolution) Section 59 (MULTIPORT Fuel Injection (MFI) (3 Of 6) - Lancer Evolution) Section 60 (MULTIPORT Fuel Injection (MFI) (4 Of 6) - Lancer Evolution) Section 61 (MULTIPORT Fuel Injection (MFI) (5 Of 6) - Lancer Evolution) Section 62 (MULTIPORT Fuel Injection (MFI) (6 Of 6) - Lancer Evolution) Section 63 (Chassis Electrical - Lancer Evolution (1 Of 5)) Section 64 (Chassis Electrical - Lancer Evolution (5 Of 5)) Section 65 (Chassis Electrical - Lancer Evolution (3 Of 5)) Section 66 (Chassis Electrical - Lancer Evolution (2 Of 5)) Section 67 (Chassis Electrical - Lancer Evolution (4 Of 5))

Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.