Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
1989 Mitsubishi Precis BaseFACTORY OEM SERVICE PROCEDURE
Alignment Specifications
WHEEL ALIGNMENT SPECIFICATIONS (GALANT)
| Application | Specification: Fraction (Decimal) | |
|---|---|---|
| Front | ||
| Camber in Degrees | 1/3 +/- 1/2 (.33 +/- .5) | |
| Caster in Degrees | 2 +/- 1/2 (2.0 +/- .5) | |
| Toe-In in Inches | 0 +/- 1/8 (0 +/- .125) | |
| Toe-In in Degrees | 0 +/- 1/4 (0 +/- .25) | |
| Rear | ||
| Camber in Degrees | -3/4 +/- 1/2 (-.75 +/- .5) | |
| Toe-In in Inches | 0 +/- 1/8 (0 +/- .125) | |
| Toe-In in Degrees | 0 +/- 1/4 (0 +/- .25) | |
WHEEL ALIGNMENT SPECIFICATIONS (MIRAGE)
| Application | Specification: Fraction (Decimal) | |
|---|---|---|
| Front | ||
| Camber in Degrees | 0 +/- 1/2 (0 +/- .50) | |
| Caster in Degrees | 2 1/4 +/- 1/2 (2.25 +/- .5) | |
| Toe-In in Inches | 0 +/- 1/8 (0 +/- .125) | |
| Toe-In in Degrees | 0 +/- 1/4 (0 +/- .25) | |
| Rear | ||
| Camber in Degrees | 5/8 +/- 1/2 (.62 +/- .5) | |
| Toe-In in Inches | 0 +/- 1/8 (0 +/- .125) | |
| Toe-In in Degrees | 0 +/- 1/4 (0 +/- .25) | |
WHEEL ALIGNMENT SPECIFICATIONS (MONTERO) (1)
| Application | Specification: Fraction (Decimal) | |||
|---|---|---|---|---|
| Front | ||||
| Camber in Degrees | 0 +/- 1/2 (0 +/- .5) | |||
| Caster in Degrees | 3/4 +/- 1/2 (.75 +/- .5) | |||
| Toe-In in Inches | 3/16 +/- 1/8 (.187 +/- .125) | |||
| Toe-In in Degrees | 3/8 +/- 1/4 (.375 +/- .25) | |||
|
||||
WHEEL ALIGNMENT SPECIFICATIONS (2WD PICKUP) (1)
| Application | Specification: Fraction (Decimal) | |||
|---|---|---|---|---|
| Front | ||||
| Camber in Degrees | 3/4 +/- 1/2 (.75 +/- .5) | |||
| Caster in Degrees | 2 1/2 +/- 1/2 (2.5 +/- .5) | |||
| Toe-In in Inches | 0 (0) | |||
| Toe-In in Degrees | 0 (0) | |||
|
||||
WHEEL ALIGNMENT SPECIFICATIONS (4WD PICKUP) (1)
| Application | Specification: Fraction (Decimal) | |||
|---|---|---|---|---|
| Front | ||||
| Camber in Degrees | 1 +/- 1/2 (1.0 +/- .5) | |||
| Caster in Degrees | 2 +/- 1 (2.0 +/- 1.0) | |||
| Toe-In in Inches | 0 (0) | |||
| Toe-In in Degrees | 0 (0) | |||
|
||||
WHEEL ALIGNMENT SPECIFICATIONS (PRECIS) (1)
| Application | Specification: Fraction (Decimal) | |||
|---|---|---|---|---|
| Front | ||||
| Camber in Degrees | 1/2 +/- 1/2 (.5 +/- .5) | |||
| Caster in Degrees | 3/3 +/- 1/4 (.75 +/- .25) | |||
| Toe-In in Inches | 0 +/- 1/16 (0 +/- .062) | |||
| Toe-In in Degrees | 0 +/- 1/8 (0 +/- .125) | |||
| Rear | ||||
| Camber in Degrees | -3/4 +/- 1/4 (-.75 +/- .25) | |||
| Toe-In in Inches | 0 +/- 1/8 (0 +/- .125) | |||
| Toe-In in Degrees | 0 +/- 1/4 (0 +/- .25) | |||
|
||||
WHEEL ALIGNMENT SPECIFICATIONS (SIGMA)
| Application | Specification: Fraction (Decimal) | ||
|---|---|---|---|
| Front | |||
| Camber in Degrees | 1/2 +/- 1/2 (.5 +/- .5) | ||
| Caster in Degrees | 5/8 +/- 1/2 (.62 +/- .5) | ||
| Toe-In in Inches | 1/16 +/- 1/8 (.062 +/- .125) | ||
| Toe-In in Degrees | 1/8 +/- 1/4 (.125 +/- .25) | ||
| Toe-Out On Turns | |||
| Inner | 35.6° | ||
| Outer | 29.3° | ||
| Rear | |||
| Camber in Degrees | -3/4 +/- 1/4 (-.75 +/- .25) | ||
| Toe-In in Inches | 1/32 +/- 1/32 (.032 +/- .031) | ||
| Toe-In in Degrees | 1/16 +/- 1/16 (.062 +/- .062) | ||
WHEEL ALIGNMENT SPECIFICATIONS (STARION) (1)
| Application | Specification: Fraction (Decimal) | |||
|---|---|---|---|---|
| Front | ||||
| Camber in Degrees | -1/2 +/- 1/2 (-.5 +/- .50) | |||
| Caster in Degrees | 5 1/2 +/- 1/2 (5.5 +/- .5) | |||
| Toe-In in Inches | 0 +/- 1/32 (0 +/- .031) | |||
| Toe-In in Degrees | 0 +/- 1/16 (0 +/- .062) | |||
| Rear | ||||
| Camber in Degrees | -1/4 +/- 1/2 (-.25 +/- .5) | |||
| Toe-In in Inches | 0 +/- 1/16 (0 +/- .062) | |||
| Toe-In in Degrees | 0 +/- 1/8 (0 +/- .125) | |||
|
||||
WHEEL ALIGNMENT SPECIFICATIONS (VAN/WAGON) (1)
| Application | Specification: Fraction (Decimal) | |||
|---|---|---|---|---|
| Front | ||||
| Camber in Degrees | 1/2 +/- 1/2 (.5 +/- .50) | |||
| Caster in Degrees | 3 1/8 +/- 1/2 (3.125 +/- .5) | |||
| Toe-In in Inches | 1/32 +/- 1/16 (.031 +/- .062) | |||
| Toe-In in Degrees | 1/16 +/- 1/8 (.062 +/- .125) | |||
|
||||
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.