Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Pretesting Inspection
If ECI system components fail, interruption of fuel supply or failure to supply proper amount of fuel for engine operation will result. The following conditions will result: engine is hard to start or does not start at all, unstable idle and/or poor driveability. Before testing ECI system, perform basic engine checks first (ignition system, incorrect engine adjustments, etc.).
| ECI Checker Check Switch Position And Details | Specifications | |||||||
|---|---|---|---|---|---|---|---|---|
| 1 | ||||||||
| Function Being Checked | Power Supply | |||||||
| Procedure | Ignition Switch "OFF" to "ON" | |||||||
| Condition | N/A | |||||||
| Normal Reading | 11-13V | |||||||
| Terminal No. | B1 | |||||||
| 2 | ||||||||
| Function Being Checked | Variable Resistor | |||||||
| Procedure | Ignition Switch "OFF" to "ON" | |||||||
| Condition | N/A | |||||||
| Normal Reading | N/A | |||||||
| Terminal No. | A10 | |||||||
| 3 | ||||||||
| Function Being Checked | Throttle Position Sensor | |||||||
| Procedure | Ignition Switch "OFF" to "ON" | |||||||
| Accelerator Fully Closed - Normal Reading | 0-0.6V | |||||||
| Accelerator Fully Opened - Normal Reading | (1) 4.5V | |||||||
| Terminal No. | A1 | |||||||
| 4 | ||||||||
| Function Being Checked | Coolant Temperature Sensor | |||||||
| Procedure | Ignition Switch "OFF" to "ON" | |||||||
| 32°F(0°C) - Normal Reading | 3.5V | |||||||
| 68°F (20°C) - Normal Reading | 2.6V | |||||||
| 104°F (40°C) - Normal Reading | 1.8V | |||||||
| 176°F (80°C) - Normal Reading | 0.6V | |||||||
| Terminal No. | A3 | |||||||
| 5 | ||||||||
| Function Being Checked | Intake Air Temperature Sensor | |||||||
| Procedure | Ignition Switch "OFF" to "ON" | |||||||
| 32°F(0°C) - Normal Reading | 3.5V | |||||||
| 68°F (20°C) - Normal Reading | 2.6V | |||||||
| 104°F (40°C) - Normal Reading | 1.8V | |||||||
| 176°F (80°C) - Normal Reading | 0.7V | |||||||
| Terminal No. | A4 | |||||||
| 6 | ||||||||
| Function Being Checked | Idle Position Switch | |||||||
| Procedure | Ignition Switch "OFF" to "ON" | |||||||
| Accelerator Fully Closed - Normal Reading | (2) OV | |||||||
| Accelerator Fully Opened - Normal Reading | 11-13V | |||||||
| Terminal No. | A5 | |||||||
| 7 | ||||||||
| Function Being Checked | Idle Speed Control Solenoid Valve | |||||||
| Procedure | Ignition Switch "OFF" to "ON" | |||||||
| Condition | Compressor Switch Off | |||||||
| Normal Reading | (3) 11-13V | |||||||
| Terminal No. | A14 | |||||||
| 8 | ||||||||
| Function Being Checked | EGR Control Solenoid Valve | |||||||
| Procedure | Ignition Switch "OFF" to "ON" | |||||||
| Condition | N/A | |||||||
| Normal Reading | 11-13V | |||||||
| Terminal No. | B4 | |||||||
| 9 | ||||||||
| Function Being Checked | Spark Retard Signal | |||||||
| Procedure | Ignition Switch "OFF" to "ON" | |||||||
| Condition | N/A | |||||||
| Normal Reading | Over 4V | |||||||
| Terminal No. | B6 | |||||||
| 10 | ||||||||
| Function Being Checked | Pressure Solenoid Valve | |||||||
| Procedure | Ignition Switch "OFF" to "ON" | |||||||
| Condition | N/A | |||||||
| Normal Reading | 0-12V In 0.6 Sec. | |||||||
| Terminal No. | B12 | |||||||
| 11 | ||||||||
| Function Being Checked | Compressor Switch | |||||||
| Procedure | Ignition Switch "OFF" to "ON" | |||||||
| Condition | Compressor Switch from "OFF to ON" | |||||||
| Normal Reading | 11-13V | |||||||
| Terminal No. | A15 | |||||||
| 12 | ||||||||
| Function Being Checked | Secondary Air Control Solenoid Valve | |||||||
| Procedure | Ignition Switch "OFF" to "ON" | |||||||
| Condition | N/A | |||||||
| Normal Reading | 11-13V | |||||||
| Terminal No. | B11 | |||||||
|
||||||||
| ECI Checker Check Switch Position And Details | Specifications | |
|---|---|---|
| 1 | ||
| Function Being Checked | Cranking Signal | |
| Procedure | Ignition Switch "OFF" to "ON" | |
| Condition | N/A | |
| Normal Reading | Over 8V | |
| Terminal No. | A13 | |
| 2 | ||
| Function Being Checked | Control Relay | |
| Procedure | Idling | |
| Condition | N/A | |
| Normal Reading | OV | |
| Terminal No. | B5 | |
| 3 | ||
| Function Being Checked | Idle Speed Control Solenoid Valve | |
| Procedure | Idling | |
| Cooler Switch "OFF" - Normal Reading | 12V | |
| Cooler Switch "OFF to ON" - Normal Reading | OV | |
| Terminal No. | A12 | |
| 4 | ||
| Function Being Checked | Ignition Pulse | |
| Procedure | Idling | |
| Condition | N/A | |
| Normal Reading | 12-14V | |
| Terminal No. | A8 | |
| 5 | ||
| Function Being Checked | Air Flow Sensor | |
| Procedure | Idling | |
| Condition | N/A | |
| Normal Reading | 3V | |
| Procedure | 3000 RPM | |
| Condition | N/A | |
| Normal Reading | 3V | |
| Terminal No. | A7 | |
| 6 | ||
| Function Being Checked | Injector 1 Pulse | |
| Procedure | Idling | |
| Condition | N/A | |
| Normal Reading | 13-14V | |
| Procedure | 3000 RPM | |
| Condition | N/A | |
| Normal Reading | 13V | |
| Terminal No. | B9 | |
| 7 | ||
| Function Being Checked | Injector 2 Pulse | |
| Procedure | Idling | |
| Condition | N/A | |
| Normal Reading | 13-14V | |
| Procedure | 3000 RPM | |
| Condition | N/A | |
| Normal Reading | 13V | |
| Terminal No. | B10 | |
| 8 | ||
| Function Being Checked | Oxygen Sensor | |
| Procedure | After Warm-Up | |
| Condition | To Heat Up Sensor | |
| Normal Reading | 0-1-2.7V | |
| Procedure | N/A | |
| Condition | To Heat Up Sensor | |
| Normal Reading | 0-1-2.7V | |
| Terminal No. | A6 | |
| 9 | ||
| Function Being Checked | EGR Control | |
| Procedure | Idling | |
| Condition | After Warm-Up | |
| Normal Reading | OV | |
| Function Being Checked | Solenoid Valve | |
| Procedure | 800-3000 RPM | |
| Condition | After Warm-Up | |
| Normal Reading | 12-15V | |
| Function Being Checked | N/A | |
| Procedure | Above 3000 RPM | |
| Condition | After Warm-Up | |
| Normal Reading | OV | |
| Terminal No. | B4 | |
| 10 | ||
| Function Being Checked | Pressure Sensor | |
| Procedure | Ignition Switch "ON and OFF" | |
| Condition | Engine Stopped | |
| Normal Reading | 1.5-2.6V | |
| Procedure | Idling | |
| Condition | Engine Stopped | |
| Normal Reading | 0.2-1.2V | |
| Terminal No. | A17 | |
| 11 | ||
| Function Being Checked | Spark Retard Signal | |
| Procedure | Idling | |
| Condition | N/A | |
| Normal Reading | Over 4V | |
| Terminal No. | B6 | |
| 12 | ||
| Function Being Checked | Secondary Air Control | |
| Procedure | Idling | |
| Condition | Water Temp. Above 131°F(55°C) | |
| Normal Reading | 0-12-15V | |
| Function Being Checked | Secondary Valve | |
| Procedure | Idling | |
| Condition | Water Temp. Above 131°F (55°C) | |
| Normal Reading | In 30 sec. | |
| Terminal No. | B11 | |
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
