Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2012 Mini Cooper Base, 2D Convertible, Automatic TransFACTORY OEM SERVICE PROCEDURE
31 90... Front Axle Troubleshooting
WARNING: This page is about a different car, the 2010 BMW 135i, 2009 BMW 135i, and 2008 BMW 135i. However, it is still accessible from the selected car via links, so may be relevant.
FRONT AXLE TROUBLESHOOTING CHART
| Fault | Cause | Remedy |
|---|---|---|
| Grinding noise (or humming) | Ā | Ā |
|
IMPORTANT:
Tire rolling noises can sound very similar to wheel bearing noises.
|
Ā | Ā |
| Test: Drive car | Ā | Ā |
|
|
|
| Vibration | Wheel imbalance | Balance wheelsĀ . See 36 10 508 STATIONARY WHEEL BALANCING . |
| Radial/lateral rim runout | Check rimsĀ , replace if necessary. See 36 10 715 CHECKING RIM FOR FACE AND RADIAL RUNOUT . | |
| Radial tire runout | Match or replace tiresĀ . See TIRES . | |
| Steering-wheel shake | Wheel imbalance | Balance wheelsĀ . See 36 10 508 STATIONARY WHEEL BALANCING . |
| Radial/lateral rim runout | Check rimsĀ , replace if necessary. See 36 10 715 CHECKING RIM FOR FACE AND RADIAL RUNOUT . | |
| Rubber mount of control arm faulty | Replace control armsĀ . See 31 12 000 REMOVING AND INSTALLING/REPLACING LEFT OR RIGHT CONTROL ARMĀ . | |
| Ball joint in control arm worn | Replace control armsĀ . See 31 12 000 REMOVING AND INSTALLING/REPLACING LEFT OR RIGHT CONTROL ARMĀ . | |
| Rubber mount of tension strut faulty | Replace rubber mounts on both tension strutsĀ . See 31 12 138 REPLACING RUBBER MOUNTS ON BOTH TENSION STRUTSĀ . | |
| Ball joint on tension strut worn | Replace both tension strutsĀ . See 31 12 080 REMOVING AND INSTALLING/REPLACING BOTH TENSION STRUTSĀ . | |
| Excessive steering wheel play/steering wheel inclination | Refer to 32 00 150 KDS CHASSIS/WHEEL ALIGNMENT CHECK WITH LOAD UP TO DESIGN POSITION or 32 00 155 KDS CHASSIS/WHEEL ALIGNMENT CHECK WITH RIDE-HEIGHT MEASUREMENT WITHOUT LOAD . | |
| Rattling noise | Bolts for reinforcement strut loose | Tighten down bolts (refer to 31 12 080 REMOVING AND INSTALLING/REPLACING BOTH TENSION STRUTSĀ ). |
| Bolt for V-strut loose | Tighten down bolts (refer to REMOVING AND INSTALLING/REPLACING V-STRUTĀ ) | |
| Bolt connection for diagonal struts loose | Tighten down bolts (refer to 51 61 018 REMOVING AND INSTALLING/REPLACING DIAGONAL STRUT, FRONT END, RIGHTĀ ) | |
| Bolts for reinforcement plate loose | Tighten down bolts to reinforcement plate | |
| Bolts for front axle carrier to engine carrier loose | Replace bolts (refer to 51 61 011 REMOVING AND INSTALLING/REPLACING V-STRUT, FRONT AXLE CARRIER, LEFT OR RIGHT ) | |
| Bolt for spring strut to swivel bearing loose | Replace bolt & nut (refer to 31 31 000 REMOVING AND INSTALLING COMPLETE LEFT OR RIGHT SPRING STRUT SHOCK ABSORBERĀ ) | |
| Ball joint in control arm worn | Replace control armsĀ . See 31 12 000 REMOVING AND INSTALLING/REPLACING LEFT OR RIGHT CONTROL ARMĀ . | |
| Ball joint on tension strut worn | Replace both tension strutsĀ . See 31 12 080 REMOVING AND INSTALLING/REPLACING BOTH TENSION STRUTSĀ . | |
| Rubber mounts for stabilizer bar bracket faulty | Replace both rubber mounts of stabilizer bar bracketĀ . See 31 35 021 REPLACING RUBBER MOUNTS OF STABILIZER RETAINING FIXTURE ON FRONT AXLE CARRIERĀ . | |
| Ball joints on stabilizer link(s) worn | Replace both stabilizer linksĀ . See 31 35 000 REMOVING AND INSTALLING/REPLACING FRONT STABILIZERĀ . | |
| Excessive tire wear | Front or rear axle alignment incorrectly adjusted | Check suspension components for damage; if necessary, carry out chassis/wheel alignment checkĀ . See 32 00 150 KDS CHASSIS/WHEEL ALIGNMENT CHECK WITH LOAD UP TO DESIGN POSITION or 32 00 155 KDS CHASSIS/WHEEL ALIGNMENT CHECK WITH RIDE-HEIGHT MEASUREMENT WITHOUT LOAD . |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- ⢠You smell fuel, burning insulation, or see smoke.
- ⢠Brakes feel soft, pull hard to one side, or make grinding noises.
- ⢠The engine overheats, stalls repeatedly, or misfires under load.
- ⢠You are missing required tools, torque specs, or safe lifting equipment.
- ⢠You are not confident in the next step or safety outcome.
