Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2005 Mercury Sable Platinum EditionFACTORY OEM SERVICE PROCEDURE
Anti-Lock Control
ANTI-LOCK BRAKE SYSTEM MODULE DIAGNOSTIC TROUBLE CODE (DTC) LIST
| DTC | Description | Source | Perform Test |
|---|---|---|---|
| B1596 | Service Continuous Code | ABS/TC | TURN the ignition switch from OFF to ON. REPEAT the ABS self-test. If any DTCs are retrieved, REFER to the ANTI-LOCK BRAKE SYSTEM (ABS) MODULE DIAGNOSTIC TROUBLE CODE (DTC) INDEX . If no DTCs are retrieved, CARRY OUT a drive test above 15 km/h (9 mph), then REFER to the SYMPTOM CHART . |
| B1676 | Battery Pack Voltage Out of Range | ABS/TC | GO to PINPOINT TEST B . |
| B1342 | ABS Module Internal Failure | ABS/TC | CLEAR the DTCs. REPEAT the self-test. If DTC B1342 is retrieved again, INSTALL a ABS module. REPEAT the self-test. |
| B1484 | Brake Pedal Input Open Circuit | ABS/TC | GO to PINPOINT TEST C . |
| C1300 | ABS Hydraulic Pump Motor Circuit Failure | ABS/TC | GO to PINPOINT TEST D . |
| C1145 | RF Wheel Speed Sensor Input Circuit Failure | ABS/TC | GO to PINPOINT TEST E . |
| C1155 | LF Wheel Speed Sensor Input Circuit Failure | ABS/TC | GO to PINPOINT TEST E . |
| C1165 | RR Wheel Speed Sensor Input Circuit Failure | ABS/TC | GO to PINPOINT TEST E . |
| C1175 | LR Wheel Speed Sensor Input Circuit Failure | ABS/TC | GO to PINPOINT TEST E . |
| C1222 | Wheel Speed Sensor Signal Mismatch | ABS/TC | GO to PINPOINT TEST F . |
| C1296 | LF Wheel Speed Sensor Signal Fault | ABS/TC | GO to PINPOINT TEST F . |
| C1297 | RF Wheel Speed Sensor Signal Fault | ABS/TC | GO to PINPOINT TEST F . |
| C1298 | RR Wheel Speed Sensor Signal Fault | ABS/TC | GO to PINPOINT TEST F . |
| C1299 | LR Wheel Speed Sensor Signal Fault | ABS/TC | GO to PINPOINT TEST F . |
| C1266 | ABS Valve Power Relay Circuit Failure | ABS/TC | GO to PINPOINT TEST G . |
| U0073 | Control Module Communication Bus Off Fault | Network Fault | Refer to MODULE COMMUNICATIONS NETWORK . |
| U1900 | CAN Communication Bus Fault-Receive Error | Network Fault | Refer to MODULE COMMUNICATIONS NETWORK . |
| U2023 | Fault-Receive From External Node | Network Fault | Refer to MODULE COMMUNICATIONS NETWORK . |
| C1805 | Mismatched Powertrain Control Module (PCM) and/or ABS Module | ABS/TC | CARRY OUT the PCM self-test. CHECK for correct PCM and ABS Module part numbers. |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
Comes to youSame-day available12-month warranty
Get a Free QuoteNo obligation. See pricing before you book.