1996 Mercury Tracer LTS, AutomaticFACTORY OEM SERVICE PROCEDURE

External Pages

's manual. Be very cautious using repair info from here because these pages may not apply to your vehicle. Different variant/trim Section 1 (Engine Controls - Service & Adjustment Specifications - 1.9L) Section 2 (Engine Controls - Adjustments - 1.9L) Section 3 (Engine Controls - Basic Engine Testing - 1.9L) Section 4 (Engine Controls - Tests W/Codes - 1.9L) Section 5 (Engine Controls - Tests W/O Codes - 1.9L) Section 6 (Engine Controls - Pin Voltage Charts - 1.9L) Section 7 (Engine - 1.9L 4-CYL - VIN [J]) Different car Section 1 (Computer Relearn Procedures) Section 2 (Computer Relearn Procedures) Section 3 (Engine Controls - Specifications - 1.8L) Section 4 (Engine Controls - Tests W/Codes - EEC (1.8L)) Section 5 (Engine Controls - Adjustments - 1.8L) Section 6 (Engine Controls - Basic Testing - 1.8L) Section 7 (Vacuum Diagrams - 1.8L) Section 8 (Wiring Diagrams - 1.8L) Section 9 (Engine Controls - Tests W/O Codes - EEC (1.8L)) Section 10 (Engine Controls - Specifications - 4.0L) Section 11 (Engine Controls - Tests W/Codes - EEC-V - 4.0L) Section 12 (Engine Controls - Specifications - 5.0L) Section 13 (Engine Controls - Tests W/Codes - EEC-V - 5.0L) Section 14 (Engine Controls - Adjustments - 4.0L) Section 15 (Engine Controls - Adjustments - 5.0L) Section 16 (Wiring Diagrams - 4.0L) Section 17 (Wiring Diagrams - Engine - 5.0L) Section 18 (Engine Controls - Basic Testing - 4.0L) Section 19 (Engine Controls - Tests W/O Codes - Engine - 4.0L) Section 20 (Engine Controls - Basic Testing - 5.0L) Section 21 (Engine - 5.0L Tests W/O Codes) Section 22 (HVAC System - A/C-Heater System - Manual) Section 23 (HVAC System - A/C-Heater System - Automatic) Section 24 (Engine Controls - Pin Voltage/PID Value Charts - Engine 4.0L) Section 25 (Engine Controls - Pin Voltage/PID Value Charts - Engine - 5.0L) Section 26 (Overhaul - F4E/4EAT - Type-GF Automatic Transmission) Section 27 (Supplemental Inflatable Restraint System - Air Bag Restraint System) Section 28 (Axle Shafts - Front) Section 29 (Rear Electronic Suspension System) Section 30 (Axle Shafts - Front) Section 31 (Axle Shafts - Front) Section 32 (Supplemental Inflatable Restraint System) Section 33 (Drive Shafts) Section 34 (Axle Shafts - Front) Section 35 (Automatic Transmission Servicing) Section 36 (Fuel Pressure Specifications)

Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.