2021 Mercedes Benz Metris Van CargoFACTORY OEM SERVICE PROCEDURE

Collision Warning System Radar Sensor, Component Description - GF30.30-S-3311TRA

Model 447.6/7/8 

With Code JA6 (Active Brake Assist System) 

Shown On Model 447.813 

Fig 1: Collision Warning System Radar Sensor Components Location - Model 447.6/7 With Code JA6 (Shown On Model 447.813)
G16501040Courtesy of MERCEDES-BENZ USA

Location 

The radar sensor for the collision warning system is located at the front right rear bumper.

Task 

The collision warning system radar sensor detects obstacles as well as the vehicles immediately ahead and warns the driver about any possible collision.

The collision warning system radar sensor transmits object data for collision avoiding intervention by the brake system to the Electronic Stability Program (ESP) control unit (N30/4).

IMPORTANT The collision warning system radar sensor recognizes a collision risk and initiates an autonomous brake application.

This results in the following tasks for the collision warning system radar sensor:

  • Reading in input factors 
  • Evaluation of input factors 
  • Transmission of initial parameters 

Reading in input factors 

The collision warning system radar sensor receives, amongst other things, the following input factors via the chassis CAN (CAN E):

  • Wheel speed and wheel rotation direction
  • Acceleration/yaw rate
  • Steering wheel angle
  • Accelerator pedal position
  • Brake pedal position
  • Switch position of combination switch (S4)
  • Driver request over the menu settings in the IC control unit (IC) (A1/1), via user interface CAN (CAN HMI) and Gateway for user interface CAN (N93/4 (model 447.8)
  • Driver request over the menu settings in the IC control unit (IC) (model 447.6/7)

The resulting functions are described in the respective function descriptions (see also block diagram or function schematic).

Evaluation of input factors 

The input factors are evaluated by the microprocessor and the corresponding components are actuated.

Transmission of initial parameters 

The collision warning system radar sensor transmits the following initial parameters via the chassis CAN:

  • Requests to output optical and acoustic warning messages in IC control unit (IC)
  • Requests to initiate PRE-SAFE® measures (with code JP1 (PRE-SAFE®))
  • Request to increase the braking torque
  • Request for torque reduction

The functions that use these signals are described in the individual function descriptions (see block diagram or function schematic).

Body 

The collision warning system radar sensor contains the following components:

  • Radar sensor
  • Control unit

Properties of the radar sensor:

  • Detection range of the radar sensor: s = 0 to 80 m for a detection angle of ∠ = 18°° ±8°°
  • 25 GHz radar sensor operating on the pulse Doppler principle for independent measurement of distance and speed

IMPORTANT The collision warning system radar sensor must be readjusted using the integrated "Service Adjustment Mode" after replacement (e.g. after an accident repair).

  Wiring diagram for collision warning system control unit Model 447.8 with code JA6 (Active Brake Assist System) PE30.30-S-2104-97VVA
    Model 447.6/7 with code JA6 (Active Brake Assist System) with Engine 622, 651 PE30.30-S-2104-97VVB
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.