Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2017 Mercedes Benz SLC43 AMGFACTORY OEM SERVICE PROCEDURE
Control Unit - BA07.08-P-1000-01A
ENGINE 152, 157, 272, 273, 276, 278Β
CONTROL UNIT
| Number | Designation | ENGINE 152 | ENGINE 272 | |
|---|---|---|---|---|
| BA07.08-P-1001-01A | Ball head support to control unit | Nm | 4 | 4 |
| BA07.08-P-1002-01A | Bolt, control unit bracket to resonance intake manifold | Nm | - | 8 |
| BA07.08-P-1003-01A | Bolt, control unit to retaining plate | Nm | - | - |
| BA07.08-P-1004-01A | Bolt, control unit holder to cylinder head/cylinder head cover | Nm | - | - |
| BA07.08-P-1005-01A | Bolt, shield over left exhaust manifold to control unit holder | Nm | - | - |
| BA07.08-P-1006-01A | Bolt, connector housing holder to control unit holder | Nm | - | - |
| BA07.08-P-1007-01A | Bolt, ECU bracket to air intake pipe | Nm | 6 | - |
CONTROL UNIT
| Number | Designation | ENGINE 273 | ENGINE 276 | |
|---|---|---|---|---|
| BA07.08-P-1001-01A | Ball head support to control unit | Nm | 4 | - |
| BA07.08-P-1002-01A | Bolt, control unit bracket to resonance intake manifold | Nm | 8 | - |
| BA07.08-P-1003-01A | Bolt, control unit to retaining plate | Nm | - | 5 |
| BA07.08-P-1004-01A | Bolt, control unit holder to cylinder head/cylinder head cover | Nm | - | 9 |
| BA07.08-P-1005-01A | Bolt, shield over left exhaust manifold to control unit holder | Nm | - | 9 |
| BA07.08-P-1006-01A | Bolt, connector housing holder to control unit holder | Nm | - | 9 |
| BA07.08-P-1007-01A | Bolt, ECU bracket to air intake pipe | Nm | - | - |
CONTROL UNIT
| Number | Designation | ENGINE 157, 278 | |
|---|---|---|---|
| BA07.08-P-1001-01A | Ball head support to control unit | Nm | 4 |
| BA07.08-P-1002-01A | Bolt, control unit bracket to resonance intake manifold | Nm | - |
| BA07.08-P-1003-01A | Bolt, control unit to retaining plate | Nm | - |
| BA07.08-P-1004-01A | Bolt, control unit holder to cylinder head/cylinder head cover | Nm | - |
| BA07.08-P-1005-01A | Bolt, shield over left exhaust manifold to control unit holder | Nm | - |
| BA07.08-P-1006-01A | Bolt, connector housing holder to control unit holder | Nm | - |
| BA07.08-P-1007-01A | Bolt, ECU bracket to air intake pipe | Nm | - |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
