2014 Mercedes Benz ML550FACTORY OEM SERVICE PROCEDURE

Purging function - GF47.30-P-3015MMR

ENGINE 157.9, 276.8, 278.9 in MODEL 166 up to model year 2016 

Fig 1: Fuel Tank Aeration And Ventilation Schematic Diagram
G10076660Courtesy of MERCEDES-BENZ USA

Schematic diagram of fuel tank aeration and ventilation (except code 494 (USA version)) 

Purging function requirements, general points 

  • Circuit 87M (engine management ON)
  • Engine started for at least 45 s
  • Coolant temperature > 40°C
  • Engine not in deceleration mode
  • Engine not in the lambda adaptation phase

Purging, general points 

When the fuel tank is being ventilated, no fuel vapors should escape into the outside air.

The fuel vapors are stored in the activated charcoal canister and burnt later in the engine.

In order to enable the purging, the ME-SFI [ME] control unit (N3/10) reads in signals from the following sensors:

  • Purging pressure sensor (B4/4)
  • Coolant temperature sensor (B11/4)
  • Charge air temperature sensor (B17/8)
  • Pressure sensor downstream of throttle valve (B28/7), engine load
  • Crankshaft Hall sensor (B70), engine rpm
  • Left and right oxygen sensors upstream of catalytic converter (G3/3, G3/4)

Ventilation of the fuel tank (operational ventilation) takes place for a running engine over the aeration/vent valves, the aeration/vent lines and the activated charcoal canister. The fuel vapors flow to the activated charcoal canister where they are stored and drawn off into the charge air distributor when purging is enabled.

To control the purge quantity, the ME-SFI [ME] control unit actuates the purging switchover valve at the ground end with a pulse width modulated signal at a frequency of 10 to Hz. The purge quantity is determined by continuously opening and closing the purging switchover valve with on-periods of varying durations.

IMPORTANT The idle speed control prevents the purging from causing a change in rpm when the engine is at idle. The fuel/air mixture is leaned out depending on the level of fuel vapors load in the activated charcoal canister.

Function sequence for purging 

The purging is described in the following points:

  • Function sequence for partial load purging 
  • Function sequence for wide open throttle purging 

Function sequence for partial load purging 

In partial load operation, the fuel vapors stored in the activated charcoal canister are drawn off by the existing vacuum through the purging switchover valve, the partial load operation check valve and the partial load vent line downstream of the throttle valve before being combusted in the engine.

Function sequence for wide open throttle purging 

Charging induces an overpressure downstream of the throttle valve in wide open throttle operation which prevents any extraction of the fuel vapors through the partial load vent line. The partial load operation check valve prevents any pressure buildup in the direction of the activated charcoal canister.

If an overpressure occurs in wide open throttle operation, the fuel vapors are extracted over the wide open throttle operation check valve and the wide open throttle vent line. The vacuum required for this is generated by a Venturi nozzle. The fuel vapors are then routed over the wide open throttle vent line, ATL and the charge air cooler to the charge air distributor.

To check whether the wide open throttle purging can be enabled, the purging switchover valve is opened suddenly three times in succession. Pressure peaks of > 120 mbar must be registered here. The purging pressure sensor detects the existing pressure conditions in the wide open throttle vent line and sends a signal to the ME-SFI [ME] control unit.

Schematic representation of purging 

Fig 2: Purge Control Electrical Function Schematic
G10076661Courtesy of MERCEDES-BENZ USA
  Electrical function schematic for purge control   PE47.30-P-2052-97NAF
  Overview of system components for gasoline injection and ignition system with direct injection ENGINE 157.9, 278.9 in MODEL 166
up to model year 2016
GF07.70-P-9998MMG
ENGINE 276.8 in MODEL 166
up to model year 2016
GF07.70-P-9998MMU
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.