Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Smooth engine running analysis, function - GF07.10-P-1030MAS
ENGINE 156.984 in MODEL 216.377, 221.077 /177 as of model year 2009 /AEJ 08Â
Function requirements for smooth engine running analysis, general pointsÂ
- Circuit 87M ON (engine control ON)
- Engine running
Smooth engine running analysis, general pointsÂ
Engine running is constantly monitored in order to protect the firewall catalytic converters from excessive thermal stresses if combustion misfires occur.
For smooth running evaluation, the ME-SFI [ME] control unit (N3/10) reads the following sensors and signals:
- LH and RH hot film MAF sensor (B2/6, B2/7), engine load
- LH and RH intake camshaft Hall sensors (B6/4, B6/5), intake camshaft positions
- LH and RH exhaust camshaft Hall sensors (B6/6, B6/7), exhaust camshaft positions
- Coolant temperature sensor ()B11/4
- Accelerator pedal sensor (B37), accelerator pedal position
- Crankshaft Hall sensor (B70), engine speed
- Instrument cluster (A1), fuel level via the chassis CAN (CAN E)
- ESP control unit (N47-5), wheel speed signal via the chassis CAN
Function sequence for smooth engine running analysisÂ
- The function sequence is described in the following steps:Â
- Function sequence for combustion misfire detectionÂ
- Function sequence for misfire counterÂ
Function sequence factors for smooth running evaluationÂ
Function sequence for combustion misfire detection For analyzing smooth engine running, the signal supplied by the crankshaft Hall sensor is analyzed using a sophisticated mathematical method to determine whether exact time synchronism exists between the individual combustions.
Each individual combustion must produce a characteristic acceleration at the increment wheel (perforated plate). If there are combustion misfires, the increment wheel turns slightly more slowly until the next ignition (torque fluctuation).
If the smooth running evaluation in the ME-SFI [ME] control unit detects combustion misfiring, the corresponding fuel injection valve (Y62) is no longer actuated after a certain number of combustion misfires. However, a maximum of two fuel injection valves may be deactivated simultaneously.
Function sequence for misfire counterÂ
The total number of combustion misfires detected is stored in the fault memory and subdivided into:
- "Cylinder-specific" combustion misfires
- "Emission limit" combustion misfires
- "Catalytic converter damaging" combustion misfires
Smooth engine running signalÂ
What is detected is combustion misfiring caused by:
- Ignition system
- Injection system
- Mechanical engine components (for example, valve seats, valve springs, unmetered air)
- Fuel deficiency
Function sequence factors for smooth running evaluationÂ
The following factors affect the smooth running evaluation:
- Engine speed and engine loadÂ
- Coolant temperatureÂ
- Recognition of an uneven road surfaceÂ
- Synchronization of fuel injection and firing orderÂ
- Fuel reserve signalÂ
- Sensor adaptationÂ
Engine speed and engine loadÂ
Using the engine speed and engine load, the ME-SFI [ME] control unit calculates a reference value for the time between two combustions.
Coolant temperatureÂ
For a cold engine more combustion misfires are permissible than for an engine at operating temperature.
Recognition of an uneven road surfaceÂ
Vibrations transmitted through the drive train may have a negative effect on engine running at certain engine speeds and load states. Therefore, the tolerance range for smooth running evaluation is increased on poor road surfaces ("wash board").
The ME-SFI [ME] control unit receives the wheel speed signal (for detection of uniform wheel speed) via the chassis CAN from the ESP control unit.
Synchronization of the fuel injection and firing orderÂ
Cylinder detection using the signals from the crankshaft Hall sensor and the intake camshaft Hall sensors or exhaust camshaft Hall sensors is required for fault storage and assessment.
Fuel reserve signalÂ
If combustion misfiring has been detected, a fault is stored if the fuel level is too low. Combustion misfires due to fuel starvation are detected via this additional information.
The SAM control unit with rear fuse and relay module (N10/2) evaluates the signals from fuel level sensors in the LH and RH fuel tank halves (B4/1, B4/2) and sends the corresponding signal via the interior CAN (CAN B) to the instrument cluster.
The ME-SFI [ME] control unit receives the fuel level information from the instrument cluster via the chassis CAN.
Sensor adaptationÂ
The tolerance range for smooth running evaluation is reduced after successful adaptation of the crankshaft Hall sensor.
In this way, the smooth running evaluation can be adapted to the specific smooth running characteristics of the engine.
The ME-SFI [ME] control unit stores the smooth operation characteristics of the engine during a deceleration phase accelerator pedal not operated) when uniform smooth operation is present. These are required as a comparison parameter for misfire detection.
The tolerance range for smooth running evaluation is preset in the ME-SFI [ME] control unit and can be adapted using the Diagnosis Assistance System (DAS) if necessary.
| Electrical function schematic for smooth running evaluation ME | Model 216 | PE07.61-P-2770-97CAC | |
| Model 221 | PE07.61-P-2770-97SAC | ||
| Â | Component description for ME-SFI [ME] control unit | N3/10 | GF07.61-P-6000MASÂ |
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
