Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Fan control function - GF07.61-P-3023G
ENGINE 111.943 /947 /951 /952 /955 /956 /957 /958 /973 /982 /983, 111.944 /975 as of 1.8.96, 111.946 as of 1.6.98, 111.921 /942 as of 1.9.98 with CODE (580) Air conditioning or Tempmatic for USA with CODE (581a) Air conditioning (Automatic)
ENGINE 111.945 in MODEL 208.335 /435 as of 1.6.98, 202.020 /080 as of 1.9.98 with CODE (580) Air conditioning or Tempmatic for USA with CODE (581a) Air conditioning (Automatic)
ENGINE 111.974 with CODE (494a) USA version with CODE (807) Model year 1997 with CODE (808) Model year 1998
ENGINE 112.910 /911 /912 /913 /914 /916 /917 /920 /921 /922 /923 /940 /941 /942 /943 /944 /946 /947 /949 /953 /954 /955 /970 /972 /973 /975
ENGINE 113.940 /941 /942 /943 /948 /960 /961 /963 /965 /966 /967 /968 /969
ENGINE 137.970
Shown on Engine 111
The ME-SFI control unit indirectly actuates the fan through the engine/ AC electric suction fan control unit.
The fan specified speed is transmitted by the ME control unit to the engine/AC electric suction fan control unit by means of a pulse width modulated signal. The on/off ratio is 10 to 90%, in which the following means e.g.:
10% electric suction fan OFF
20% electric suction fan ON, minimum speed
90% electric suction fan ON, maximum speed
If the actuation is faulty, the electric suction fan rotates with maximum rotational speed.
The status of the air conditioning or automatic air conditioning is transmitted from the instrument cluster via the CAN to the ME control unit. The fan specified speed is dependent on this status.
CAN capable instrument cluster required, that the HHT or STAR DIAGNOSIS is programmed according to with/without air conditioning or automatic air conditioning.
Engine 112 at production start-up as of 3/97 with viscous fan clutch, fan control phased in as of 7/97.
On engine 137 and in Model 203, 209, 211, 230 an electric suction fan is built-in with integrated control. The engine/air conditioning electric suction fan control unit is deleted.
| Motor electronics control unit, location/task/design/function | other than engine 111 EVO | GF07.61-P-5000F | |
| Engine 111 EVO | GF07.61-P-5000GS | ||
| Coolant temperature sensor, location/task/design/function | Engine 104, 111 | GF07.04-P-5026G | |
| Engine 112, 113, 137 | GF07.04-P-5026A |
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
