Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2000 Mercedes Benz S430FACTORY OEM SERVICE PROCEDURE
Instrument Cluster Version Coding (54.30/77)
Publication date: 2003-01-09
Reference number: 54.30/77
INSTRUMENT CLUSTER VERSION CODING
Reference number: 54.30/77
INSTRUMENT CLUSTER VERSION CODING
TECHNICAL SERVICE BULLETIN
Reference Number(s): P-B-54.30/77, Date of Issue:Â
January 9, 2003
| MERCEDES-BENZ: | Model 220, Model Years 2000 through 2003 |
| GROUP: | 54 - Electrical System |
SUBJECT
Instrument Cluster Version Coding
SERVICE INFORMATION
If you encounter "Display Defective" or diagnostic indicator lamps illuminated after the installation of an instrument cluster on the above-mentioned models, perform the following.
- Ensure that the latest software is installed into STAR Diagnosis.
- Using STAR Diagnosis enter into the following menus and verify that the proper instrument cluster version coding is selected. Control Units -> Information & Communication -> ICM Instrument Cluster with Maintenance Interval Display -> Control Unit Adaptations -> Version Coding -> Coding Specific for Instrument Cluster.
- If the vehicle's specific version coding differs from the table below correct and adapt the appropriate changes.
INSTRUMENT CLUSTER VERSION CODING
| Engine Torque Interface for ASSYST | CAN ID 310 2000 Model Years, CAN ID 312 2001-2003 Model Years |
| Redundant Distance Storage | Active for 2002 and 2003 Model Year, Not Active for 2000 and 2001 Model Year |
| Reversible Gurtstraffer - Reversible Seatbelt PRESAFE | Present for 2003, Not Present for 2000, 2001, and 2002 |
| Fahrer Fahrdynamiksitz - Driver Drive-Dynamic Seat | Present for 2003 if equipped, Not Present for 2000, 2001, and 2002 |
| Standardeinstellung Fuer Fahrer Fahrdynamiksitz - Standard Setting for Driver's Drive-Dynamic Seat | Active for 2003, Not Activated for 2000, 2001, and 2002 |
| Beifahrer Fahrdynamiksitz - Passenger Drive-Dynamic Seat | Present for 2003 if equipped, Not Present for 2000, 2001, and 2002 |
| Standardeinstellung Fuer Beifahrer Fahrdynamiksitz - Standard Setting for Passenger's Drive-Dynamic Seat | Active for 2003, Not Activated for 2000, 2001, and 2002 |
| Spiegeleinklappung Bei Fahrzeugverriegelung - Folding Exterior Mirror When Locking | Present for 2003, Not Present for 2000, 2001, and 2002 |
| Standardeinstellung Fuer Spiegeleinklappung Bei Fahrzeugverriegelung -- Standard Settings for Folding Exterior Mirror When Locking | Active for 2003, Not Activated for 2000, 2001 and 2002 |
| Information and Communication System | Not Present |
| Audio Gateway | Not Present |
| Data Communication - Interior CAN Bus | Standard Setting: Transmit |
| Data Communication - Engine CAN Bus | Do Not Transmit |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
