Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Self-Diagnostic System
Connect Hand-Held Tester (965 589 00 01 00) to data link connector. Following manufacturer's instructions, retrieve codes from PSE control module. Record DTCs and go to appropriate test procedure. See DTC IDENTIFICATION CHART (PNEUMATIC SYSTEM EQUIPMENT CONTROL MODULE) table.
| DTC | Cause | Test/Remedy | ||||||
|---|---|---|---|---|---|---|---|---|
| 012 | Driver's Door Safety Switch Time Exceeded | (1) | ||||||
| 013 | Fuel Door Safety Switch Time Exceeded | (2) | ||||||
| 014 | Passenger's Door Safety Switch Time Exceeded | (3) | ||||||
|
||||||||
| DTC | Cause | Test/Remedy | ||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 002 | Central Locking System Air Demand Too High | (1) | ||||||||||||||||||||
| 003 | Retractable Trunk Lid Grip System Air Demand Too High | (2) | ||||||||||||||||||||
| 004 | Retractable Rear Headrest/ Remote Trunk Release Air Demand Too High | (3) | ||||||||||||||||||||
| 005 | Orthopedic Seat Air Demand Too High | (4) | ||||||||||||||||||||
| 006 | Manifold Vacuum Assist Air Demand Too High | (4) | ||||||||||||||||||||
| 007 | Lock Switch Circuit One Resistance Too High | (5) | ||||||||||||||||||||
| 008 | Lock Switch Circuit 2 Resistance Too High | (5) | ||||||||||||||||||||
| 009 | Retractable Rear Headrest Switch Resistance Too High | (6) | ||||||||||||||||||||
| 010 | Interior Central Locking Switch Resistance Too High | (7) | ||||||||||||||||||||
| 011 | Driver's Door Pin Switch Resistance Too High | (8) | ||||||||||||||||||||
| 012 | Remote Trunk Release Switch Resistance Too High | (9) | ||||||||||||||||||||
| 013 | Trunk Lid Microswitch Resistance Too High | (10) | ||||||||||||||||||||
| 014 | Lock Switch Circuit One Signal For More Than 2 Minutes | (5) | ||||||||||||||||||||
| 015 | Lock Switch Circuit 2 Signal For More Than 2 Minutes | (5) | ||||||||||||||||||||
| 016 | Interior Central Locking Switch Signal For More Than 2 Minutes | (7) | ||||||||||||||||||||
| 017 | Retractable Rear Headrest Switch Signal For More Than 2 Minutes | (6) | ||||||||||||||||||||
| 018 | Remote Trunk Release Switch Signal For More Than 2 Minutes | (9) | ||||||||||||||||||||
|
||||||||||||||||||||||
| DTC | Cause | Test/Remedy | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 012 | Driver's Door Safety Switch Time Exceeded | (1) | ||||||||||||
| 013 | Fuel Door Safety Switch Time Exceeded | (2) | ||||||||||||
| 014 | Passenger's Door Safety Switch Time Exceeded | (3) | ||||||||||||
| B1000 | Combination Control Module (CCM) | Replace CCM | ||||||||||||
| B1010 | Low Voltage | (4) | ||||||||||||
| B1011 | Excessive Voltage | (4) | ||||||||||||
| B1021 | No Communication With PSE Control Module | (5) | ||||||||||||
| B1024 | CAN L Data Line Fault | (5) | ||||||||||||
| B1024 | CAN H Data Line Fault | (5) | ||||||||||||
| B1100 | Control Line Between DAS Control Module Combination Control Module Short | (6) | ||||||||||||
| B1436 | Driver's Door Safety Switch Time Exceeded | (1) | ||||||||||||
| B1436 | Fuel Door Safety Switch Time Exceeded | (2) | ||||||||||||
| B1436 | Passenger's Door Safety Switch Time Exceeded | (3) | ||||||||||||
| B1729 | PSE Control Module Fault | Replace PSE Control Module | ||||||||||||
|
||||||||||||||
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
