1998 Mercedes Benz E430FACTORY OEM SERVICE PROCEDURE

Electrical Component Locator: Splices

SPLICES

Component Component Location
Z3 In wiring channel, by left rear door sill.
Z3/11 In harness tray, at base of windshield.
Z3/28 In wiring channel, by left rear door sill.
Z3/29 Beneath front fuse box.
Z3/31 In wiring channel, at base of left "A" pillar.
Z6/16 In harness tray, at base of windshield.
Z6/23 Approximately, 200 mm from CTEL transmitter-receiver connector.
Z7 In wiring channel, by right rear door sill.
Z7/1 In harness tray, at base of windshield.
Z7/19 Beneath front fuse box.
Z7/24 Beneath control module box.
Z7/25 Beneath control module box.
Z7/26 In wiring channel, at base of right "A" pillar.
Z7/30 In harness tray, at base of windshield.
Z7/31 In wiring channel, by left front door sill.
Z7/33 In wiring channel, at base of right "A" pillar.
Z7/37 Approximately, 100 mm from CTEL transmitter-receiver connector.
Z11/1 Under center console.
Z11/2 Under center console.
Z12 Under center console.
Z21/5 In wiring channel, by left rear door sill.
Z21/6 In wiring channel, by left rear door sill.
Z21/10 Under center console.
Z21/11 In wiring channel, by right rear door sill.
Z28/18 In wiring channel, by left rear door sill.
Z28/29 At left front of luggage compartment.
Z28/30 At left front of luggage compartment.
Z29/1 In wiring channel, by left rear door sill.
Z29/2 In wiring channel, by left rear door sill.
Z30 In harness tray, at base of windshield.
Z30/1 In harness tray, at base of windshield.
Z30/2 In harness tray, at base of windshield.
Z30/3 In wiring channel, by right rear door sill.
Z30/4 In wiring channel, by right rear door sill.
Z37 In wiring channel, by right rear door sill.
Z37/1 In wiring channel, by right rear door sill.
Z37/2 In wiring channel, at base of right "A" pillar.
Z37/3 In wiring channel, at base of right "A" pillar.
Z38 In wiring channel, by left rear door sill.
Z40 In wiring channel, by right front door sill.
Z41 In wiring channel, by right rear door sill.
Z42 In wiring channel, by left rear door sill.
Z44 In wiring channel, by right front door sill.
Z44/1 In wiring channel, by right front door sill.
Z45 In wiring channel, by right rear door sill.
Z81 In harness tray, at base of windshield.
Z81/4 In harness tray, at left rear of center console.
Z84/3 In wiring channel, at base of right "A" pillar.
Z84/4 In wiring channel, at base of right "A" pillar.
Z88 In wiring channel, at base of right "A" pillar.
Z89 In wiring channel, at base of right "A" pillar.
Z90 In wiring channel, at base of right "A" pillar.
Z92 Beneath front fuse box.
Z99/1 In wiring channel, at base of right "A" pillar.
Z99/2 In wiring channel, at base of right "A" pillar.
Z99/3 In wiring channel, by right rear door sill.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.