Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
1995 Mercedes Benz SL320FACTORY OEM SERVICE PROCEDURE
Diagnostic Trouble Code Definitions
ENGINE CONTROL MODULE DIAGNOSTIC TROUBLE CODE REFERENCE CHART
| Generic DTC(1) | Mercedes-Benz DTC | Description | Test step/Remedy | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 1 | - | No malfunction in system | |||||||||||
| 2 | 002 | ECT sensor (B11/3) short circuit | 8.0, see SEQUENTIAL MULTIPORT FUEL INJECTION SYSTEM TESTS 8.0 & 8.1 | ||||||||||
| 2 | 003 | ECT sensor (B11/3) open circuit | 8.0, see SEQUENTIAL MULTIPORT FUEL INJECTION SYSTEM TESTS 8.0 & 8.1 | ||||||||||
| 2 | 004 | ECT sensor (B11/3) implausible | 8.0, see SEQUENTIAL MULTIPORT FUEL INJECTION SYSTEM TESTS 8.0 & 8.1 | ||||||||||
| 2 | 005 | ECT sensor (B11/3) intermittent contact | Contacts in connector of B11/3 or N3/4 | ||||||||||
| 3 | 006 | IAT sensor (B17) short circuit | 9.0, see SEQUENTIAL MULTIPORT FUEL INJECTION SYSTEM TESTS 9.0 & 9.1 | ||||||||||
| 3 | 007 | IAT sensor (B17) open circuit | 9.0, see SEQUENTIAL MULTIPORT FUEL INJECTION SYSTEM TESTS 9.0 & 9.1 | ||||||||||
| 3 | 008 | IAT sensor (B17) intermittent contact | Contacts in connector of B17 or N3/4 | ||||||||||
| 4 | 009 | Hot film MAF sensor (B2/5) air flow implausibly high | 4.0 - 5.0, see Sequential Multiport Fuel Injection System Tests 3.0-4.0 - Sequential Multiport Fuel Injection System Tests 4.1-7.0 Engine friction excessive. |
||||||||||
| 4 | 010 | Hot film MAF sensor (B2/5) open circuit | 4.0 - 5.0, see Sequential Multiport Fuel Injection System Tests 3.0-4.0 - Sequential Multiport Fuel Injection System Tests 4.1-7.0 | ||||||||||
| 5 | 011 | CTP switch (M16/1s2 or M16/2s2) throttle valve angle implausibly large | 11.0, see Sequential Multiport Fuel Injection System Tests 10.0-12.0 | ||||||||||
| 5 | 012 | CTP switch (M16/1s2 or M16/2s2) air flow implausibly high | 11.0, see Sequential Multiport Fuel Injection System Tests 10.0-12.0 | ||||||||||
| 5 | 013 | CTP switch (Ma6/1s2 or M16/2s2) intermittent contact | 11.0, see Sequential Multiport Fuel Injection System Tests 10.0-12.0 | ||||||||||
| 6 | 014 | Not applicable for U.S.A version vehicles | - | ||||||||||
| 6 | 015 | Not applicable for U.S.A. version vehicles | - | ||||||||||
| 6 | 016 | Not applicable for U.S.A. version vehicles | - | ||||||||||
| 7 | 017 | Not applicable for U.S.A. version vehicles | - | ||||||||||
| 7 | 018 | Not applicable for U.S.A. version vehicles | - | ||||||||||
| 7 | 019 | Not applicable for U.S.A. version vehicles | - | ||||||||||
| 8 | 020 | ISC system at lower control stop | Intake air leak, throttle body binding, CC or EA operating in "limp-home" mode. | ||||||||||
| 8 | 021 | ISC system at upper control stop | Intake air leak, throttle body binding, CC or EA operating in "limp-home" mode. | ||||||||||
| 8 | 022 | CC or EA indicates "limp-home" mode | Intake air leak, throttle body binding. Adjust throttle linkage, erase DTC's in HFM-SFI control module. |
||||||||||
| 9(2) | 023 | O2S (before TWC) (G3/2) sensor voltage too high | 14.0, see Sequential Multiport Fuel Injection System Tests 13.0-15.1 | ||||||||||
| 9(2) | 024 | O2S (before TWC) (G3/2) cold or open circuit | 14.0, see Sequential Multiport Fuel Injection System Tests 13.0-15.1 | ||||||||||
| 9(2) | 025 | O2S1 (before TWC) (G3/2) sensor voltage implausible | 14.0, see Sequential Multiport Fuel Injection System Tests 13.0-15.1 | ||||||||||
| 10 | 026 | Except model 124 O2S 2 (after TWC) (G3/1) sensor voltage too high |
16.0, see Sequential Multiport Fuel Injection System Tests 16.0 | ||||||||||
| 10 | 027 | Except model 124 O2S (after TWC) (G3/1) cold or open circuit |
16.0, see Sequential Multiport Fuel Injection System Tests 16.0 | ||||||||||
| 10 | 028 | Except model 124 O2S (after TWC) G3/1) sensor voltage implausible |
16.0, see Sequential Multiport Fuel Injection System Tests 16.0 | ||||||||||
| 11 | 029 | O2S 1 (before TWC) heater (G3/2) current too low | 15.0, see Sequential Multiport Fuel Injection System Tests 13.0-15.1 | ||||||||||
| 11 | 030 | O2S (before TWC) heater (G3/2) current too high | 15.0, see Sequential Multiport Fuel Injection System Tests 13.0-15.1 | ||||||||||
| 11 | 031 | O2S 1 (before TWC) heater (G3/2) short circuit | 15.0, see Sequential Multiport Fuel Injection System Tests 13.0-15.1 | ||||||||||
| 12 | 032 | Except model 124 O2S 2 (after TWC) heater (G3/1) current too low |
17.0, see Sequential Multiport Fuel Injection System Tests 16.1-18.0 | ||||||||||
| 12 | 033 | Except model 124 O2S 2 (after TWC heater (G3/1) current too high |
17.0, see Sequential Multiport Fuel Injection System Tests 16.1-18.0 | ||||||||||
| 12 | 034 | Except model 124 O2S 2 (after TWC) heater (G3/1) short circuit |
17.0, see Sequential Multiport Fuel Injection System Tests 16.1-18.0 | ||||||||||
| 13 | 035 | O2S system operating at rich limi, mixture too lean | Intake air leak, fuel injectors, diaphragm pressure regulator | ||||||||||
| 13 | 036 | O2S system operating at lean limit, mixture too rich | Intake air leak, fuel injectors, diaphragm pressure regulator | ||||||||||
| 14 | 037 | Injector (Y62y1), cylinder 1 short circuit to plus | 19.0, see Sequential Multiport Fuel Injection System Tests 18.1-19.1 | ||||||||||
| 14 | 038 | Injector (Y62y1), cylinder 1 open/short circuit to ground | 19.0, see Sequential Multiport Fuel Injection System Tests 18.1-19.1 | ||||||||||
| 15 | 039 | Injector (Y62y2), cylinder 2 short circuit to plus | 20.0, see Sequential Multiport Fuel Injection System Tests 20.0-21.0 | ||||||||||
| 15 | 040 | Injector (Y62y2), cylinder 2 open/short circuit to ground | 20.0, see Sequential Multiport Fuel Injection System Tests 20.0-21.0 | ||||||||||
| 16 | 041 | Injector (Y62y3), cylinder 3 short circuit to plus | 21.0, see Sequential Multiport Fuel Injection System Tests 20.0-21.0 | ||||||||||
| 16 | 042 | Injector (Y62y3), cylinder 3 oopen/short circuit to ground | 21.0, see Sequential Multiport Fuel Injection System Tests 20.0-21.0 | ||||||||||
| 17 | 043 | Injector (Y62y4), cylinder 4 short circuit to plus | 22.0, see Sequential Multiport Fuel Injection System Tests 21.1-22.1 | ||||||||||
| 17 | 044 | Injector (Y62y4), cylinder 4 open/short circuit to ground | 22.0, see Sequential Multiport Fuel Injection System Tests 21.1-22.1 | ||||||||||
| 18 | 045 | Injector (Y62y5), cylinder 5 short circuit to plus | 23.0, see Sequential Multiport Fuel Injection System Tests 23.0-23.1 | ||||||||||
| 18 | 046 | Injector (Y62y5), cylinder 5 open/short circuit to ground | 23.0, see Sequential Multiport Fuel Injection System Tests 23.0-23.1 | ||||||||||
| 019 | 047 | Injector (Y62y6), cylinder 6 short circuit to plus | 24.0, see Sequential Multiport Fuel Injection System Tests 24.0-24.1 | ||||||||||
| 19 | 048 | Injector (Y62y6), cylinder 6 open/short circuit to ground | 24.0, see Sequential Multiport Fuel Injection System Tests 24.0-24.1 | ||||||||||
| 20 | 049 | Self-adaptation at idle speed too rich | Intake air leak, fuel injectors, diaphragm pressure regulator, engine wear (reset slf-adaptation following repair) | ||||||||||
| 20 | 050 | Self-adaptation at the idle speed too lean | Intake air leak, fuel injectors, diaphragm pressure regulator, engine wear (reset self-adaptation following repair) | ||||||||||
| 20 | 051 | Self-adaptation at lower partial load too rich | Intake air leak, fuel injectors, diaphragm pressure nregulator, engine wear (reset self-adaptation following repair) | ||||||||||
| 20 | 052 | Self-adaptation at lower partial load too lean | Intake air leak, fuel injectors, diaphragm pressure regulator, engine wear (reset self-adaptation following repair) | ||||||||||
| 20 | 053 | Self-adaptation at upper partial load too rich | Intake air leak, fuel injectors, diaphragm pressure regulator, engine wear (reset self-adaptation follwing repair) | ||||||||||
| 20 | 054 | Self-adaptation at upper partial load too lean | Intake air leak, fuel injectors, diaphragm pressure regulator, engine wear (reset self-adaptation following repair) | ||||||||||
| 21 | 061 | Ignition output 3 or ignition coil (T1/3) for cylinder 1 misfires | 13.0, 16.0 and 19.0, see Ignition System Tests 12.0-13.0 , Ignition System Tests 16.0-19.1 | ||||||||||
| 21 | 062 | Ignition output 3 or ignition coil (T1/3) for cylinder 6 misfires | 13.0, 16.0 and 19.0, see Ignition System Tests 12.0-13.0 , Ignition System Tests 16.0-19.1 | ||||||||||
| 21 | 063 | Ignition output 3 or ignition coil (T1/3) current value not obtained | 13.0, 16.0 and 19.0, see Ignition System Tests 12.0-13.0 , Ignition System Tests 16.0-19.1 | ||||||||||
| 22 | 055 | Ignition output 1 or ignition coil (T1/1) for cylinder 2 misfires | 11.0, 14.0 and 17.0, see Ignition System Tests 9.0-11.0 , Ignition System Tests 14.0-15.1 and Ignition System Tests 16.0-19.1 | ||||||||||
| 22 | 056 | Ignition output 1 or ignition coil (T1/1) for cylinder 5 misfires | 11.0, 14.0 and 17.0, see Ignition System Tests 9.0-11.0 , Ignition System Tests 14.0-15.1 and Ignition System Tests 16.0-19.1 | ||||||||||
| 22 | 057 | Ignition output 1 or ignition coil (T1/1) current value not obtained | 11.0, 14.0 and 17.0, see Ignition System Tests 9.0-11.0 , Ignition System Tests 14.0-15.1 and Ignition System Tests 16.0-19.1 | ||||||||||
| 23 | 058 | Ignition output 2 or ignition coil (T1/2) for cylinder 3 misfires | 12.0, 15.0 and 18.0, see Ignition System Tests 12.0-13.0 , Ignition System Tests 14.0-15.1 and Ignition System Tests 16.0-19.1 | ||||||||||
| 23 | 059 | Ignition output 2 or ignition coil (T1/2) for cylinder 4 misfires | 12.0, 15.0 and 18.0, see Ignition System Tests 12.0-13.0 , Ignition System Tests 14.0-15.1 and Ignition System Tests 16.0-19.1 | ||||||||||
| 23 | 060 | Ignition output 2 or ignition coil (T1/2) current value not obtained | 12.0, 15.0 and 18.0, see Ignition System Tests 12.0-13.0 , Ignition System Tests 14.0-15.1 and Ignition System Tests 16.0-19.1 | ||||||||||
| 24 | 064 | CKP sensor (L5) signal not recognized/implausible | 7.0, see Ignition System Tests 7.0-8.2 | ||||||||||
| 24 | 065 | CKP sensor (L5) magnet is missing (segment control) CKP sensor (L5) number of teeth implausible (increment control) |
7.0, see Ignition System Tests 7.0-8.2 | ||||||||||
| 24 | 066 | CKP sensor (L5) rpm implausibly high | 7.0, see Ignition System Tests 7.0-8.2 | ||||||||||
| 25 | 067 | CMP sensor (L5/1) implausible/not recognized (segment control) | 8.0, see Ignition System Tests 7.0-8.2 | ||||||||||
| 25 | 067 | Camshaft Hall-effect sensor (B6/1) implausible/not recognized (increment control) | 9.0, see Ignition System Tests 9.0-11.0 | ||||||||||
| 26 | 068 | Not applicable for U.S.A. version vehicles | - | ||||||||||
| 26 | 069 | Not applicable for U.S.A. version vehicles | - | ||||||||||
| 27 | 070 | TN-signal output (rpm signal), short circuit to ground | 10.0, see Sequential Multiport Fuel Injection System Tests 10.0-12.0 | ||||||||||
| 27 | 071 | TN-signal output (rpm signal), short circuit to plus | 10.0, see Sequential Multiport Fuel Injection System Tests 10.0-12.0 | ||||||||||
| 28 | 072 | VSS not recognized | 27.0, see Sequential Multiport Fuel Injection System Tests 25.0-28.0 | ||||||||||
| 28 | 073 | VSS implausibly high | 27.0, see Sequential Multiport Fuel Injection System Tests 25.0-28.0 | ||||||||||
| 29 | 075 | Not applicable for U.S.A. version vehicles | - | ||||||||||
| 30 | 076 | FP relay module (K27) open/short circuit | 6.0, see Sequential Multiport Fuel Injection System Tests 4.1-7.0 | ||||||||||
| 31 | 077 | Not applicable for U.S.A. version vehicles | - | ||||||||||
| - | 078 | Not applicable for U.S.A. version vehicles | - | ||||||||||
| 32 | 079 | KS 1 (A16) open circuit | Replace knock sensors (KS) | ||||||||||
| 32 | 080 | KS 2 (A16) open circuit | Replace knock sensors (KS) | ||||||||||
| 33 | 081 | Maximum retard setting on at least one cylinder has been reached | Increased tendency to knock due to poor fuel quality, combustion chamber carbon build-up or mechanical damage. | ||||||||||
| 33 | 082 | Ignition angle deviation between the individual cylinders is > 6° CKA | Increased tendency to knock due to poor fuel quality, combustion chamber carbon build-up or mechanical damage | ||||||||||
| 34 | 083 | Knock control evaluation circuit in engine control module (N3/4) defective | N3/4 | ||||||||||
| - | 084 | Momentary fault in self-adaptation of closed throttle speed/partial load | Momentary malfunction in fuel mixture preparation | ||||||||||
| 35 | 085 | Model 124, 129 and 140: AIR pump switchover valve (Y32) and/or electromagnetic AIR pump clutch (Y33) Model 202: AIR pump switchover valve (Y32) and/or AIR relay module (K17) open/short circuit |
28.0, see Sequential Multiport Fuel Injection System Tests 25.0-28.0 | ||||||||||
| 36 | 086 | Purge control valve (Y58/1) open/short circuit | 29.0 - 30.0, see Sequential Multiport Fuel Injection System Tests 28.1-29.1 , Sequential Multiport Fuel Injection System Tests 30.0-31.1 | ||||||||||
| 36 | 087 | Purge control valve (Y58/1) short circuit to plus | 29.0 - 30.0, see Sequential Multiport Fuel Injection System Tests 28.1-29.1 , Sequential Multiport Fuel Injection System Tests 30.0-31.1 | ||||||||||
| 37 | 088 | Upshift delay switchover valve (Y3/3) open/short circuit | 34.0, see Sequential Multiport Fuel Injection System Tests 32.0-34.0 | ||||||||||
| 38 | 089 | Adjustable camshaft timing solenoid (Y49) short circuit to plus | 31.0 - 32.0, see Sequential Multiport Fuel Injection System Tests 30.0-31.1 - Sequential Multiport Fuel Injection System Tests 32.0-34.0 | ||||||||||
| 38 | 090 | Adjustable camshaft timing solenoid (Y49) open/short circuit to ground | 31.0 - 32.0, see Sequential Multiport Fuel Injection System Tests 30.0-31.1 - Sequential Multiport Fuel Injection System Tests 32.0-34.0 | ||||||||||
| 39 | 091 | EGR switchover valve (Y27) short circuit to plus | 38.0 - 40.0, see Sequential Multiport Fuel Injection System Tests 38.0-39.0 - Sequential Multiport Fuel Injection System Tests 40.0-44.0 | ||||||||||
| 39 | 092 | EGR switchover valve (Y27) open/short circuit to ground | 38.0 - 40.0, see Sequential Multiport Fuel Injection System Tests 38.0-39.0 - Sequential Multiport Fuel Injection System Tests 40.0-44.0 | ||||||||||
| 40 | 093 | Transmission overload protection switch (S65) short circuit to ground | 10.0, see Ignition System Tests 9.0-11.0 | ||||||||||
| 40 | 094 | Transmission overload protection switch (S65) closed and 2nd gear recognized | 10.0, see Ignition System Tests 9.0-11.0 | ||||||||||
| 40 | 095 | Transmission overload protection switch (S65) open and 2nd gear recognized | 10.0, see Ignition System Tests 9.0-11.0 | ||||||||||
| 40 | 096 | Transmission overload protection switch (S65) implausible | 10.0, see Ignition System Tests 9.0-11.0 | ||||||||||
| 41 | 097 | CAN communication from engine control module (N3/4) defective | 37.0, see Sequential Multiport Fuel Injection System Tests 36.1-37.0 | ||||||||||
| 42 | 098 | CAN communication from ASR control module (N30/1) defective | 36.0, see Sequential Multiport Fuel Injection System Tests 35.0-36.0 | ||||||||||
| 42 | 099 | CAN communication from EA/CC/ISC control module (N4/1) or CC/ISC control module (N4/3) defective | 36.0, see Sequential Multiport Fuel Injection System Tests 35.0-36.0 | ||||||||||
| 42 | 100 | CAN communication from diagnostic module (OBD II) (N59/1) defective | 36.0, see Sequential Multiport Fuel Injection System Tests 35.0-36.0 | ||||||||||
| 43 | 101 | Starter signal (circuit 50) not present | 7.0, see Sequential Multiport Fuel Injection System Tests 4.1-7.0 | ||||||||||
| 44 | 102 | Not applicable for U.S.A. version vehicles | - | ||||||||||
| 44 | 103 | Not applicable for U.S.A. version vehicles | - | ||||||||||
| 45 | 104 | Fuel safety shut-off of electronic accelerator or cruise control active | 12.0, see Sequential Multiport Fuel Injection System Tests 10.0-12.0 , 13.0, see Sequential Multiport Fuel Injection System Tests 13.0-15.1 |
||||||||||
| 46 | 105 | Resonance intake manifold switchover valve (Y22/6) short circuit to plus | 33.0, see Sequential Multiport Fuel Injection System Tests 32.0-34.0 | ||||||||||
| 46 | 106 | Resonance intake manifold switchover valve (Y22/6) open/short circuit to ground | 33.0, see Sequential Multiport Fuel Injection System Tests 32.0-34.0 | ||||||||||
| - | 107(3) | Control of ignition coil preloading voltage exceeds limits | 14.1 and 15.1, see Ignition System Tests 14.0-15.1 Engine control module (N3/4) |
||||||||||
| 48 | 108 | O2S 2 (after TWC) heater relay module (K35) short circuit to plus | 18.0, see Sequential Multiport Fuel Injection System Tests 16.1-18.0 | ||||||||||
| 48 | 109 | O2S (after TWC) heater relay module (K35) open/short circuit to ground | 18.0, see Sequential Multiport Fuel Injection System Tests 16.1-18.0 | ||||||||||
| 49 | 110 | Voltage supply circuit 87 U at engine control module (N3/4) implausible | 2.0, see Sequential Multiport Fuel Injection System Tests 2.0-2.2 | ||||||||||
| 49 | 111 | Voltage supply circuit 87 U at engine control module (N3/4) low voltage | 2.0, see Sequential Multiport Fuel Injection System Tests 2.0-2.2 | ||||||||||
| 50 | 112 | Engine control module (N3/4) | N3/4 | ||||||||||
| - | 113(4) | Engine control module (N3/4) not coded | Code N3/4 | ||||||||||
| - | 114(4) | Engine control module identification of N3/4 faulty | Code N3/4, if necessary, preplace N3/4 | ||||||||||
| - | 115(4) | engine control module code bytes of N3/4 faulty | Code N3/4, if necessary, replace N3/4 | ||||||||||
| - | 116(5) | CAN communication from RCL control module (N54) faulty | 36.1, see | ||||||||||
| - | 117(5) | Engine starts with RCL system locked | Incorrect operation, clear DTC memory | ||||||||||
| - | 120 | Not applicable for U.S.A. version vehicles | - | ||||||||||
| - | 121 | Not applicable for U.S.A. version vehicles | - | ||||||||||
| - | 122 | Not applicable for U.S.A. version vehicles | - | ||||||||||
| - | 125 | Engine control module (N3/4) | N3/4 | ||||||||||
| - | 126 | Engine control module (N3/4) | N3/4 | ||||||||||
| - | 127 | ISC and CC/ISC actuators interchanged | Replace actuator | ||||||||||
| - | 128 | Engine control module (N3/4) | N3/4 | ||||||||||
| - | 129 | Engine control module (N3/4) | N3/4 | ||||||||||
| - | 130 | Not applicable for U.S.A. version vehicles | - | ||||||||||
| - | 131 | Engine control module (N3/4) | N3/4 | ||||||||||
| - | 132 | Engine control module (N3/4) | N3/4 | ||||||||||
| - | 133 | EA/CC/ISC or CC/ISC actuator | Perform learning process on engine control module with HHT. If the fault is still presnt, replace actuator | ||||||||||
| - | 134 | Engine control module (N3/4) | N3/4 | ||||||||||
| - | 135 | Not applicable for U.S.A version vehicles | - | ||||||||||
| - | 136 | Not applicable for U.S.A version vehicles | - | ||||||||||
| - | 137 | Engine control module (N3/4) | N3/4 | ||||||||||
| - | 138 | EA/CC/ISC or CC/ISC actuator | Perform learning process on engine control module with HHT. If the fault is still present, preplace actuator. | ||||||||||
| - | 139 | Not applicable for U.S.A. version vehicles | - | ||||||||||
| - | 140 | Engine control module (N3/4) | N3/4 | ||||||||||
| 141 | Engine control module (N3/4) | N3/4 | |||||||||||
| 142 | Engine control module (N3/4) | N3/4 | |||||||||||
| - | 143 | Not applicable for U.S.A. version vehicles | - | ||||||||||
| - | 144 | Engine control module (N3/4) | N3/4 | ||||||||||
|
|
|||||||||||||
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
