Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2018 Mazda 6 Grand TouringFACTORY OEM SERVICE PROCEDURE
360DEGREES View Monitor DTCS
360DEGREES VIEW MONITOR DTCS
| DTC No. | Description | Refer To |
|---|---|---|
| B115E:54 | Aiming not performed | (See DTC B115E:54 (360°VIEW MONITOR CONTROL MODULE) .) |
| B12BD:00 | Rear mount camera malfunction | (See DTC B12BD:00 (360°VIEW MONITOR CONTROL MODULE) .) |
| B12BD:16 | Rear mount camera internal voltage malfunction | (See DTC B12BD:16 (360°VIEW MONITOR CONTROL MODULE) .) |
| B12BD:17 | Rear mount camera internal voltage malfunction | (See DTC B12BD:17 (360°VIEW MONITOR CONTROL MODULE) .) |
| B12C0:00 | Side camera (RH) malfunction | (See DTC B12C0:00 (360°VIEW MONITOR CONTROL MODULE) .) |
| B12C1:00 | Side camera (LH) malfunction | (See DTC B12C1:00 (360°VIEW MONITOR CONTROL MODULE) .) |
| B148E:00 | Front camera malfunction | (See DTC B148E:00 (360°VIEW MONITOR CONTROL MODULE) .) |
| U0010:88 | Module communication error (MS-CAN) | (See DTC U0010:88/U0100:00/U0131:00/U0140:00/U0155:00/U0159:00/U0214:00/U0232:00 (360°VIEW MONITOR CONTROL MODULE) .) |
| U0100:00 | Communication error with PCM | |
| U0131:00 | Communication error with electric power steering (EPS) control module | |
| U0140:00 | Communication error with front body control module (FBCM) | |
| U0155:00 | Communication error with instrument cluster | |
| U0159:00 | Communication error with parking assist unit | |
| U0214:00 | Communication error with start stop unit | |
| U0232:00 | Communication error with blind spot monitoring (BSM) control module (LH) | |
| U0401:00 | Error signal received from PCM | (See DTC U0401:00 (360°VIEW MONITOR CONTROL MODULE) .) |
| U0420:00 | Error signal received from electric power steering (EPS) control module | (See DTC U0420:00 (360°VIEW MONITOR CONTROL MODULE) .) |
| U0420:82 | Error signal received from electric power steering (EPS) control module | (See DTC U0420:82 (360°VIEW MONITOR CONTROL MODULE) .) |
| U0420:83 | Error signal received from electric power steering (EPS) control module | (See DTC U0420:83 (360°VIEW MONITOR CONTROL MODULE) .) |
| U0422:82 | Error signal received from front body control module (FBCM) | (See DTC U0422:82 (360°VIEW MONITOR CONTROL MODULE) .) |
| U0423:00 | Error signal received from instrument cluster | (See DTC U0423:00 (360°VIEW MONITOR CONTROL MODULE) .) |
| U045A:81 | Error signal received from parking assist unit | (See DTC U045A:81 (360°VIEW MONITOR CONTROL MODULE) .) |
| U0515:82 | Error signal received from start stop unit | (See DTC U0515:82 (360°VIEW MONITOR CONTROL MODULE) .) |
| U0533:81 | Error signal received from blind spot monitoring (BSM) control module (LH) | (See DTC U0533:81 (360°VIEW MONITOR CONTROL MODULE) .) |
| U3000:41 | 360°view monitor control module internal malfunction | (See DTC U3000:41 (360°VIEW MONITOR CONTROL MODULE) .) |
| U3000:49 | 360°view monitor control module internal malfunction | (See DTC U3000:49 (360°VIEW MONITOR CONTROL MODULE) .) |
| U3000:95 | VIN mismatch | (See DTC U3000:95 (360°VIEW MONITOR CONTROL MODULE) .) |
| U3003:16 | 360°view monitor control module low power supply voltage input | (See DTC U3003:16 (360°VIEW MONITOR CONTROL MODULE) .) |
| U3003:17 | 360°view monitor control module high power supply voltage input | (See DTC U3003:17 (360°VIEW MONITOR CONTROL MODULE) .) |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
