2016 Mazda MX-5 Miata Club, Automatic TransFACTORY OEM SERVICE PROCEDURE

Purge Control System Inspection

If simulation function of M-MDS is used: 

  1. Start the engine.
  2. Remove the seal cover. (See SEAL COVER REMOVAL/INSTALLATION .)
  3. Disconnect the evaporative hose between the purge solenoid valve and the charcoal canister.
  4. Put a finger to the purge solenoid valve and verify that there is no vacuum applied when the engine is cold.
    • If there is a vacuum, inspect the following:
  5. Connect the M-MDS to the DLC-2 and verify that DTC P0443:00 is displayed. (See ON-BOARD DIAGNOSTIC TEST [PCM (SKYACTIV-G 2.0)] .)
  6. Select the EVAPCP simulation item. (See ON-BOARD DIAGNOSTIC TEST [PCM (SKYACTIV-G 2.0)] .)
  7. Increase the duty value of the purge solenoid valve to 50 % and inspect if the operation sound of the valve is heard.
    • If the operation sound is heard, inspect for loose or damaged evaporative hoses. (Intake manifold-Purge solenoid valve-Charcoal canister)
    • If the operation sound is not heard, perform the purge solenoid valve inspection. (See PURGE SOLENOID VALVE INSPECTION .)
  8. Warm up the engine to normal operating temperature.
  9. Monitor the EVAPCP PID using the M-MDS, and drive the vehicle approx. 2, 000 rpm for 30 s or more. (See ON-BOARD DIAGNOSTIC TEST [PCM (SKYACTIV-G 2.0)] .)
    • If the EVAPCP PID is 0 %  , inspect the following PIDs:
RELATED PIDS

Item (definition) Unit/Condition Definition Condition/Specification (Reference)
APP1 % Accelerator pedal opening angle (absolute value) input from APP sensor No. 1
  • Accelerator pedal released: Approx. 15.29%
  • Accelerator pedal fully depressed: Approx. 90.98%
V APP sensor No. 1 voltage
  • Accelerator pedal released: Approx. 0.77 V
  • Accelerator pedal fully depressed: Approx. 4.55 V
APP2 % Accelerator pedal opening angle (absolute value) input from APP sensor No. 2
  • Accelerator pedal released: Approx. 7.84%
  • Accelerator pedal fully depressed: Approx. 45.49%
V APP sensor No. 2 voltage
  • Accelerator pedal released: Approx. 0.38 V
  • Accelerator pedal fully depressed: Approx. 2.27 V
EVAPCP % Purge solenoid valve control duty value
  • Idle (after warm up): Approx. 0% (ECT is 94 °C {201 °F})
  • Racing (Engine speed 2, 000 rpm): 0% (ECT is 94 °C {201 °F})
  • Racing (Engine speed 4, 000 rpm): Approx. 10.1% (ECT is 94 °C {201 °F})
MAF g/Sec Mass air flow input from MAF sensor
  • Displays MAF
V MAF sensor voltage
  • Ignition switched ON (engine off) (MAF: 0.39 g/s {0.052 lb/min}): Approx. 0.72 V (ECT is 89 °C {192 °F})
  • Idle (after warm up) (MAF: 4.29 g/s {0.567 lb/min}): Approx. 1.15 V (ECT is 88 °C {190 °F})
  • Racing (engine speed is 2, 000 rpm) (MAF: 4.32 g/s {0.571 lb/min}): Approx. 1.15 V (ECT is 89 °C {192 °F})
  • Racing (engine speed is 4, 000 rpm) (MAF: 12.71 g/s {1.681 lb/min}): Approx. 1.66 V (ECT is 89 °C {192 °F})
LOAD % Ratio of actual amount of intake air to the maximum air charging amount (mass volume) of cylinder
  • Idle (after warm up): Approx. 27.05% (ECT is 91 °C {196 °F})
  • Racing (engine speed is 2, 000 rpm): Approx. 16.86% (ECT is 89 °C {192 °F})
  • Racing (engine speed is 4, 000 rpm): Approx. 17.64% (ECT is 87 °C {189 °F})
TP_REL % Throttle valve opening angle (relative value) with value at throttle valve fully close timing as the start point
  • Accelerator pedal released: Approx. 12.15%
  • Accelerator pedal fully depressed: Approx. 81.96%

If simulation function of M-MDS is not used: 

  1. Start the engine.
  2. Remove the seal cover. (See SEAL COVER REMOVAL/INSTALLATION .)
  3. Disconnect the evaporative hose between the purge solenoid valve and the charcoal canister.
  4. Put a finger to the purge solenoid valve and verify that there is no vacuum applied when the engine is cold.
    • If there is a vacuum, inspect the following:
  5. Set the vehicle on a dynamometer or chassis roller.
    WARNING:
    • When the dynamometer or chassis roller is operating, there is a possibility that the operator may come into contact with or be caught up in the rotating parts, leading to serious injuries or death. When performing work while the dynamometer or chassis roller is operating, be careful not to contact or be caught up in any of the rotating parts.
  6. Drive the vehicle at an engine speed to approx. 2000 rpm for 30 s or more.
  7. Put a finger to the purge solenoid valve and verify that there is no vacuum applied during Step 3.
    • If there is no vacuum, inspect the following:
    • If there is vacuum, inspect the following:
      • Evaporative hose (Purge solenoid valve-Charcoal canister)
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.