2014 Mazda 3 SV, Automatic TransFACTORY OEM SERVICE PROCEDURE

Using The M-MDS

NOTE:
  1. Connect the M-MDS to the DLC-2.
  2. Switch the ignition ON (engine off).
  3. Measure the PID value.
    • If PID value is not within the specification, follow the instructions in action column.
      NOTE:
      • The PID/DATA MONITOR function monitors the calculated value of the input/output signals in the PCM. Therefore, an output device malfunction is not directly indicated as a malfunction of the monitored value for the output device. If a monitored value of an output device is out of specification, inspect the monitored value of the input device related to the output control.
      • The simulation items that are used in the engine control system operation inspection are as follows.
        • ACCS, AIRSHUT_DSD, ARPMDES, EVAPCP, EVAPCV, FAN1, FAN3, FP, INJ_1, INJ_2, INJ_3, INJ_4, OIL_P_SOL, Test, VT EX_DES
PCM TERMINAL SPECIFICATION

-: Not applicable
Item (definition) Unit/Condition Definition Value type Condition/Specification (Reference) PCM terminal
AAT(5) °C, °F Ambient air temperature -
  • Displays ambient air temperature
 2I
AC_PRES(6) KPa {MPa}, mBar {Bar}, psi, in H20 Refrigerant pressure input from refrigerant pressure sensor Calculation
  • Displays refrigerant pressure
 2AX
V Refrigerant pressure sensor voltage Input
  • Refrigerant pressure is 1.0 MPa {10 kgf/cm2 , 145 psi}: Approx. 1.58 V
  • Refrigerant pressure is 1.1 MPa {11 kgf/cm2 , 160 psi}: Approx. 1.75 V
  • Refrigerant pressure is 1.2 MPa {12 kgf/cm2 , 174 psi}: Approx. 1.88 V
AC_REQ Off/On A/C switch status received by PCM via CAN Input
  • A/C switch off: Off
  • A/C switch on: On
 CAN (2AK, 2AL)
ACCS Off/On A/C relay status input from A/C relay Input
  • A/C relay off: Off
  • A/C relay on: On
 2AF
AIRSHUT_ACT (1) % Active air shutter position Calculation
  • Active air shutter position is 0°: 0%
  • Active air shutter position is 90°: 100%
 LIN (2Z)
AIRSHUT_CAL (1) Not Done/Completed Active air shutter fully open/closed position learning status Calculation
  • Displays active air shutter fully open/closed position learning status
 -
ALTF % Field coil current control signal output to generator Calculation
  • Ignition switched ON (engine off): 0%
  • Idle: Approx. 42%
  • Racing (Engine speed is 2, 000 rpm): Approx. 29%
 1BR(1), 1BE(2)
ALTF_ACT(1) % Actually measured value of field coil current signal input from generator Calculation
  • Displays actual generator field current control duty value
 -
ALTT V(2) V Generator output voltage Input
  • Idle (no E/L): Approx. 14 V (This is internal calculation value and differs from terminal voltage)
 1AF
AMB_TEMP °C, °F Actually measured ambient temperature input from ambient temperature sensor Calculation
  • Displays ambient air temperature
 21
APP % Accelerator pedal opening angle (relative value) with the fully released status as 0% and fully depressed status as 100% Calculation
  • Accelerator pedal released: Approx. 0%
  • Accelerator pedal fully depressed: Approx. 100%
 -
APP1 % Accelerator pedal opening angle (absolute value) input from APP sensor No. 1 Calculation
  • Accelerator pedal released: Approx. 15%
  • Accelerator pedal fully depressed: Approx. 82%
 2AN
V APP sensor No. 1 voltage Input
  • Accelerator pedal released: Approx. 0.75 V
  • Accelerator pedal fully depressed: Approx. 4.1 V
APP2 % Accelerator pedal opening angle (absolute value) input from APP sensor No. 2 Calculation
  • Accelerator pedal released: Approx. 7.45%
  • Accelerator pedal fully depressed: Approx. 41%
 2AS
V APP sensor No. 2 voltage Input
  • Accelerator pedal released: Approx. 0.38 V
  • Accelerator pedal fully depressed: Approx. 2.05 V
ARPMDES RPM Target engine speed Calculation
  • Displays target engine speed
 -
BARO KPa {MPa}, mBar {Bar}, psi, in H20 Actually measured barometric pressure input from barometric pressure sensor built into PCM Calculation
  • Displays BARO
 -
V BARO sensor voltage Input
  • Ignition switched ON (at sea level): Approx. 4.08 V
BATT_CUR(1) A Battery current Calculation
  • Displays battery charge/discharge current value
 CAN (2AK, 2AL)
BATT_DAY(1) - Number of days elapsed since current sensor initialization Calculation
  • Displays vehicle battery days in service.
 CAN (2AK, 2AL)
BATT_RES(1) - Battery internal resistance (estimated) Calculation
  • Displays battery inferred internal resistance.
 CAN (2AK, 2AL)
BATT_SOC(1) % Battery charge condition (estimated) Calculation
  • Displays battery estimated state of charge.
 CAN (2AK, 2AL)
BATT_TEMP(1) °C, °F Battery temperature Calculation
  • Displays battery fluid temperature
 CAN (2AK, 2AL)
BATT_V(1) V Battery voltage Calculation
  • Displays battery voltage
 CAN (2AK, 2AL)
BOO High/Low Brake switch (No. 1 signal) input status Calculation
  • Brake pedal released: Low
  • Brake pedal fully depressed: High
 2G
BPA High/Low Brake switch (No. 2 signal) input status Calculation
  • Brake pedal released: Low
  • Brake pedal fully depressed: High
 2R
CAP_SYS_10(1) Off/On Open circuit in capacitor (i-ELOOP) (power cannot be supplied from capacitor) Calculation
  • Capacitor internal circuit is not open: Off
  • Capacitor internal circuit is open: On
 -
CAP_SYS 13(1) Off/On Capacitor (i-ELOOP) capacitance malfunction Calculation
  • Capacitor (i-ELOOP) capacitance status is not normal: On
  • Capacitor (i-ELOOP) capacitance status is normal: Off
 -
CAP_SYS 14(1) Off/On Capacitor (i-ELOOP) capacitance deterioration Calculation
  • Capacitor (i-ELOOP) capacitance status deteriorates: On
  • Capacitor (i-ELOOP) capacitance status is normal: Off
 -
CAP_SYS 15(1) Off/On Capacitor (i-ELOOP) internal resistance malfunction Calculation
  • Internal resistance status in capacitor (i-ELOOP) is not normal: On
  • Internal resistance status in capacitor (i-ELOOP) is normal: Off
 -
CAP_SYS 16(1) Off/On Capacitor (i-ELOOP) internal resistance deterioration Calculation
  • Internal resistance status in capacitor (i-ELOOP) deteriorates: On
  • Internal resistance status in capacitor (i-ELOOP) is normal: Off
 -
CATT11_DSD °C, °F Estimated catalytic converter temperature Calculation
  • Displays estimated catalytic converter temperature
 -
CHRGLP Off/On Charging system warning light illumination status Calculation
  • Charging system warning light not illuminated: Off
  • Charging system warning light illuminated: On
 -
CPP(3) Off/On Clutch pedal position Calculation
  • Clutch pedal fully depressed: On
  • Clutch pedal released: Off
 2J
CPP/PNP(3) Off/On Shift lever position Calculation
  • Other than neutral: Off
  • Neutral: On
 1K
ECT °C, °F Engine coolant temperature Calculation
  • Displays ECT
 1AK
V ECT sensor No. 1 voltage Input
  • ECT is 20 °C {68 °F}: Approx. 3.10 V
  • ECT is 40 °C {104 °F}: Approx. 2.16 V
  • ECT is 60 °C {140 °F}: Approx. 1.40 V
  • ECT is 80 °C {176 °F}: Approx. 0.87 V
  • ECT is 100 °C {212 °F}: Approx. 0.54 V
ECT2_V(5) V ECT sensor No. 2 voltage Input
  • ECT is 20 °C {68 °F}: Approx. 3.10 V
  • ECT is 40 °C {104 °F}: Approx. 2.16 V
  • ECT is 60 °C {140 °F}: Approx. 1.40 V
  • ECT is 80 °C {176 °F}: Approx. 0.87 V
  • ECT is 100 °C {212 °F}: Approx. 0.54 V
 2F
EQ_RAT11 - Excess air factor (estimated value) to theoretical air/fuel ratio (14.7) by fuel feedback control Calculation
  • Idle (after warm up): Approx. 1
 -
EQ_RAT11_DS D - Target excess air factor (estimated value) to theoretical air/fuel ratio (14.7) by fuel feedback control Calculation
  • Indicate target lambda (Excess air factor = supplied air amount/theoretical air/fuel ratio)
 -
ETC_ACT ° Actual throttle valve opening angle Calculation Ignition switched ON (engine off) 
  • Accelerator pedal released: Approx, 12.89°
  • Accelerator pedal fully depressed: Approx. 86.03 °

Idle (after warm up) 


  • Accelerator pedal released: Approx. 3.2 °
 -
ETC_DSD % Target throttle valve opening angle (percent) Calculation
  • Displays target TP opening angle (percent)
 -
° Target throttle valve opening angle Calculation
  • Displays target TP opening angle
EVAPCP % Purge solenoid valve control duty value Calculation
  • Idle (after warm up): Approx. 0%
  • Racing (Engine speed 2, 000 rpm): 4.3-35%
  • Racing (Engine speed 4, 000 rpm): Approx. 66%
 1AI
EVAPCV(5) Off/On CV solenoid valve operation status Calculation
  • Simulation item (EVAPCV) is ON: On
 2BF
FAN1 Off/On Cooling fan relay No. 1 operation status Calculation
  • Cooling fan relay No. 1 off: Off
  • Cooling fan relay No. 1 on: On
 2AU
FAN3 Off/On Cooling fan relay No. 2 and No. 3 operation status Calculation
  • Cooling fan relay No. 2 and No. 3 off: Off
  • Cooling fan relay No. 2 and No. 3 on: On
 2AV
FCL(5) Off/On Check fuel cap warning light illumination status Calculation
  • Check fuel cap warning light not illuminated: Off
  • Check fuel cap warning light illuminated: On
 -
FIA - Fuel injection amount Calculation
  • Displays fuel injection amount
 -
FLI % Fuel level Calculation
  • Fuel gauge level F: Approx. 100%
  • Fuel gauge level E: Approx. 0%
 CAN (2AK, 2AL)
FP Off/On Fuel pump relay operation status Calculation
  • Ignition switched ON (engine off): Off
  • Cranking: On
  • Idle (after warm up): On
 2AQ
FP_DUTY % Fuel pump control module control duty value Calculation
  • Ignition switched ON (engine off): Approx. 55.74%
  • Cranking: Approx. 95%
  • Idle (after warm up): Approx. 55.74%
 2AE
FTP(5) KPa {MPa}, mBar {Bar}, psi, in H20 Fuel tank pressure Calculation
  • Displays fuel tank pressure
 2Y
V Fuel tank pressure sensor voltage Input
  • Fuel tank pressure is equal to barometric pressure: Approx. 2.6 V
FUEL_P_DSD KPa {MPa}, mBar {Bar}, psi, in H20 Target fuel pressure (high pressure fuel pump) Calculation
  • Displays target fuel pressure (high pressure fuel pump)
 -
FUEL_PRES KPa {MPa}, mBar {Bar}, psi, in H20 Fuel pressure Calculation
  • Displays fuel pressure
 1CA
V Fuel pressure sensor voltage Input
  • Fuel pressure is 3.0 MPa {31 kgf/cm2 , 435 psi}: Approx. 0.92 V
  • Fuel pressure is 4.8 MPa {49 kgf/cm2 , 696 psi}: Approx. 1.17 V
FUELPW Sec Fuel injection pulse width (fuel injector energization time) output to fuel injector Calculation
  • Idle (after warm up): Approx. 1.4 ms
  • Racing (engine speed is 2, 000 rpm): Approx. 1.1 ms
  • Racing (engine speed is 4, 000 rpm): Approx. 1.0 ms
 No. 1:1DO/1DP
No. 2:1DW/1DX
No. 3:1EA/1EB
No. 4:1DS/1DT
FUELSYS OL/CL/OL_Drive/OL_Fault/CL_Fault Feedback status of fuel injection control is displayed
OL: Feedback control is disabled at cold engine start
CL: During feedback control by A/F sensor and HO2S
OL_Drive: While feedback control is stopped
OL_Fault: Feedback control is disable due to system malfunction
CL_Fault: During feedback control with either A/F sensor or HO2S having a malfunction		 Calculation
  • Idle (after warm up): OL or CL
  • Racing (engine speed is 2, 000 rpm): CL
  • Deceleration fuel cut (accelerator pedal released from engine speed of 4, 000 rpm or more): OL-Drive
 -
GEAR(4) Unknown/1st/2nd/3rd/4th/5th/6th/Not in P/Park/Neutral/Drive/Reverse Gear commanded Calculation
  • Selector lever at P position: Park
  • Selector lever at R position: Reverse
  • Selector lever at N position: Neutral
  • Selector lever is in D or M position while vehicle is stopped: 1st
 CAN (2AK, 2AL)
HTR11 Off/On A/F sensor heater operation status Calculation
  • Ignition switched ON (engine off): Off
  • Idle (after warm up): On
 1BY
% A/F sensor heater control duty value Calculation
  • Ignition switched ON (engine off): 0%
  • Idle (after warm up): Approx. 40%
HTR12 Off/On HO2S heater operation status Calculation
  • Ignition switched ON (engine off): Off
  • Idle (after warm up): On
 2C
% HO2S heater control duty value Calculation
  • Ignition switched ON (engine off): 0%
  • Idle (after warm up): Approx. 40%
IAT °C, °F Intake air temperature (No. 1) Calculation
  • Displays IAT (No. 1)
 2U
V IAT sensor No. 1 voltage Input
  • IAT is 20 °C {68 °F}: Approx. 2.70 V
  • IAT is 40 °C {104 °F}: Approx. 1.80 V
  • IAT is 60 °C {140 °F}: Approx. 1.20 V
IAT2 °C, °F Intake air temperature (No. 2) Calculation
  • Displays IAT (No. 2)
 1CE
V IAT sensor No. 2 voltage Input
  • IAT2 is 20 °C {68 °F}: Approx, 3.57 V
  • IAT2 is 40 °C {104 °F}: Approx. 2.70 V
  • IAT2 is 60 °C {140 °F}: Approx. 1.87 V
INGEAR(3) Off/On Gears are engaged Calculation
  • When the following conditions are satisfied: On
    • Other than neutral
    • Clutch pedal released
  • Except above: Off
 CAN (2AK, 2AL)
ISC_FBK % ISC feedback value Calculation
  • Displays ISC feedback value
 -
ISC_FBK_LRN % Learning value for calculating ISC feedback amount Calculation
  • Displays ISC feedback learning value
 -
IVS Off Idle/Idle CTP condition Calculation
  • Racing: Off Idle
  • Idle: Idle
 -
KNOCKR ° Camshaft retard amount when knocking determined Calculation
  • Ignition switched ON (engine off): 0 °
  • Idle (after warm up): 0 °
 -
LOAD % Ratio of actual amount of intake air to the maximum air charging amount (mass volume) of cylinder Calculation
  • Idle (after warm up): Approx. 17.64%
  • Racing (engine speed is 2, 000 rpm): Approx. 14.51%
  • Racing (engine speed is 4, 000 rpm): Approx. 21.17%
 -
LONGFT1 % Fuel learning correction amount estimated based on A/F sensor signal Calculation
  • Idle (after warm up): Approx. -2.34%
  • Racing (engine speed is 2, 000 rpm): Approx. -0.78%
  • Racing (engine speed is 4, 000 rpm): Approx. -0.78%
 -
LONGFT12 % Fuel learning correction amount estimated based on heated oxygen sensor signal Calculation
  • Idle (after warm up): Approx. 0%
 -
LOW_OIL Never Detected/Detected Engine oil pressure condition Never Detected: Engine oil pressure is high Detected: Engine oil pressure is low Calculation
  • Ignition switched ON (engine off): Detected
  • Idle (after warm up): Detected
  • Racing (engine speed is 2, 000 rpm): Never Detected
 -
M_GEAR(3) Neutral/1st gear/2nd gear/3rd gear/4th gear/5th gear/6th gear/Reverse/Undefined/Auto/In_Progress/YSF/Error Manual gear position Calculation
  • Displays manual gear position
 CAN (2AK, 2AL)
MAF g/Sec Mass air flow Calculation
  • Displays MAF
 2BC
V MAF sensor voltage Input
  • Ignition switched ON (engine off) (MAF: 0.59 g/s {0.078 lb/min}): Approx. 0.72 V
  • Idle (after warm up) (MAF: 2.17 g/s {0.287 lb/min}): Approx. 0.86 V
  • Racing (engine speed is 2, 000 rpm) (MAF: 4.73 g/s {0.626 lb/min}): Approx. 1.07 V
MAP KPa {MPa}, mBar {Bar}, psi, in H20 Manifold absolute pressure Calculation
  • Displays MAP
 1BW
V MAP sensor voltage Input
  • Ignition switched ON (engine off) (MAP:101 kPa {1.03 kgf/cm2 , 14.6 psi}): Approx. 4.07 V
  • Idle (after warm up) (MAP: 33 kPa {0.34 kgf/cm2 , 4.8 psi}): Approx. 1.34 V
  • Racing (engine speed is 2, 000 rpm) (MAP: 26 kPa {0.27 kgf/cm2 , 3.8 psi}): Approx. 1.05 V
MF_CAT1 - Number of misfires in No. 1 cylinder leading to catalytic converter temperature increase (catalytic converter temperature increases due to fuel combustion around catalytic converter after misfire) Calculation
  • Displays number of misfires corresponding to possible catalytic converter damage (No. 1 cylinder)
 -
MF_CAT_2 - Number of misfires in No. 2 cylinder leading to catalytic converter temperature increase (catalytic converter temperature increases due to fuel combustion around catalytic converter after misfire) Calculation
  • Displays number of misfires corresponding to possible catalytic converter damage (No. 2 cylinder)
 -
MF_CAT_3 - Number of misfires in No. 3 cylinder leading to catalytic converter temperature increase (catalytic converter temperature increases due to fuel combustion around catalytic converter after misfire) Calculation
  • Displays number of misfires corresponding to possible catalytic converter damage (No. 3 cylinder)
 -
MF_CAT_4 - Number of misfires in No. 4 cylinder leading to catalytic converter temperature increase (catalytic converter temperature increases due to fuel combustion around catalytic converter after misfire) Calculation
  • Displays number of misfires corresponding to possible catalytic converter damage (No. 4 cylinder)
 -
MF_CAT_FCC - Threshold of malfunction determination for number of misfires (total number in all cylinders) leading to catalytic converter temperature increase Calculation
  • Displays number of misfire determinations (for catalytic converter)
 -
MF_CAT_TTL - Number of misfires (total number in all cylinders) leading to catalytic converter temperature increase Calculation
  • Displays number of misfires corresponding to possible catalytic converter damage (total)
 -
MF_EMI1 - Number of misfires in No. 1 cylinder under conditions required by emission regulations Calculation
  • Displays number of misfires possibly affecting emission (No. 1 cylinder)
 -
MF_EMI_2 - Number of misfires in No. 2 cylinder under conditions required by emission regulations Calculation
  • Displays number of misfires possibly affecting emission (No. 2 cylinder)
 -
MF_EMI_3 - Number of misfires in No. 3 cylinder under conditions required by emission regulations Calculation
  • Displays number of misfires possibly affecting emission (No. 3 cylinder)
 -
MF_EMI_4 - Number of misfires in No. 4 cylinder under conditions required by emission regulations Calculation
  • Displays number of misfires possibly affecting emission (No. 4 cylinder)
 -
MF_EMI_FCC - Threshold of malfunction determination for number of misfires (total number in all cylinders) under conditions required by emission regulations Calculation
  • Displays number of misfire determinations (for emission)
 -
MF_EMI_TTL - Number of misfires (total number in all cylinders) under conditions required by emission regulations Calculation
  • Displays number of misfires possibly affecting emission (total)
 -
MIL Off/On Check engine light illumination status Calculation
  • Check engine light not illuminated: Off
  • Check engine light illuminated: On
 -
MIL_DIS km {mph}, ft, mi Travelled distance since check engine light illuminated Calculation
  • Displays travelled distance since check engine light illuminated
 -
O2S11 μA A/F sensor current Input
  • Idle (after warm up): Approx. -39 μA
  • Deceleration fuel cut (accelerator pedal released from engine speed of 4, 000 rpm or more): Approx. 3.84 mA
 1AB
O2S12 V HO2S voltage Input
  • Idle (after warm up): 0-1.0 V
  • Deceleration fuel cut (accelerator pedal released from engine speed of 4, 000 rpm or more): Approx. 0 V
 2AI/2AG
OIL_P_SOL Off/On Engine oil solenoid valve operation status Calculation
  • ECT below 98 °C {208 °F} and engine speed below 4, 000 rpm: On
  • ECT above 98 °C {208 °F} or engine speed above 4, 000 rpm: Off
 1AS
OIL_TEMP °C, °F Estimated engine oil temperature Calculation
  • Displays estimated engine oil temperature
 -
PN_SW(4) Open/Closed Parking/neutral Calculation
  • Selector lever at P position or N position: Closed
  • Except above: Open
 CAN (2AK, 2AL)
PRE_CHG_DIS(1) km, ft {mi} Distance at pre-charge Calculation
  • Displays distance at pre-charge
 -
RO2FT1 % Fuel correction amount based on HO2S signal including SHRTFT12 and LONGFT12 Calculation
  • Idle (after warm up): Approx. 0.5%
  • Deceleration fuel cut (accelerator pedal released from engine speed of 4, 000 rpm or more): Approx.3.99%
 -
RPM RPM Engine speed Calculation
  • Displays engine speed
 1AD
SHRTFT1 % Fuel feedback correction amount estimated based on A/F sensor signal Calculation
  • Idle (after warm up): Approx. 1.56%
  • Racing (engine speed is 2, 000 rpm): Approx. -3.12%
  • Racing (engine speed is 4, 000 rpm): Approx. -8.59%
 -
SHRTFT12 % Fuel feedback correction amount estimated based on HO2S signal Calculation
  • Idle (after warm up): Approx. 0%
 -
SPARKADV ° Ignition timing Calculation
  • Displays ignition timing
 -
Test Off/On Test mode operation condition due to forced override operation Calculation
  • Test mode off: Off
  • Test mode on: On
 -
TH_M(5) - Thermostat monitor Calculation
  • Indicates heat radiation ratio (heat radiation when thermostat is malfunctioning/heat radiation when thermostat is normal) when thermostat monitoring is finished
 -
TH_M_MAX(5) - Thermostat monitor max Calculation
  • Indicates upper limit of heat radiation ratio (heat radiation when thermostat is malfunctioning/heat radiation when thermostat is normal) for thermostat monitoring execution
 -
TH_M_MIN(5) - Thermostat monitor min Calculation
  • Indicates lower limit of heat radiation ratio (heat radiation when thermostat is malfunctioning/heat radiation when thermostat is normal) for thermostat monitoring execution
 -
TP_REL % Throttle valve opening angle (relative value) with value at throttle valve fully open timing as the start point Calculation
  • Accelerator pedal released: Approx. 12%
  • Accelerator pedal fully depressed: Approx. 82%
 -
TP1 V TP sensor No. 1 voltage Input
  • Accelerator pedal released: Approx. 1.11 V
  • Accelerator pedal fully depressed: Approx. 4.59 V
 1BP
% Throttle valve position No. 1 Calculation
  • Accelerator pedal released: Approx. 22%
  • Accelerator pedal fully depressed: Approx. 92%
TP2 V TP sensor No. 2 voltage Input
  • Accelerator pedal released: Approx. 3.92 V
  • Accelerator pedal fully depressed: Approx. 0.41 V
 1BU
% Throttle valve position No. 2 Calculation
  • Accelerator pedal released: Approx. 22%
  • Accelerator pedal fully depressed: Approx. 82%
TPCT V TP sensor No. 1 voltage at CTP Calculation
  • Ignition switched ON (engine off): Approx. 0.5 V
 -
TPCT2 V TP sensor No. 2 voltage at CTP Calculation
  • Ignition switched ON (engine off): Approx. 4.5 V
 -
VPWR V Battery positive voltage Input
  • Displays battery voltage
 2O
VSS KPH, MPH Vehicle speed Calculation
  • Displays vehicle speed
 CAN (2AK, 2AL)
VT EX_DES ° Desired exhaust valve timing Calculation
  • Displays desired exhaust valve timing
 -
VT_IN_ACT ° Actual intake valve timing Calculation
  • Displays actual intake valve timing
 1Y
VT IN_DES ° Desired intake valve timing Calculation
  • Displays desired intake valve timing
 -
VT_EX_ACT ° Actual exhaust valve timing Calculation
  • Displays actual exhaust valve timing
 1T
VT_EX_DUTY % OCV control duty value Calculation
  • Idle (after warm up): Approx. 0%
  • Racing (engine speed is 2, 000 rpm): Approx. 46%
 1AN
(1) Vehicles with i-ELOOP
(2) Vehicles without i-ELOOP
(3) MTX
(4) ATX
(5) U.S.A. and CANADA
(6) Vehicles with manual air conditioner
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.

Rather have a pro handle this?

A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.

Comes to youSame-day available12-month warranty
Get a Free Quote

No obligation. See pricing before you book.