2012 Mazda MX-5 Miata L4-2.0LFACTORY OEM SERVICE PROCEDURE

Component Tests and General Diagnostics





PCM INSPECTION [LF]

Not Using the M-MDS

NOTE:
- The PCM terminal voltage can vary with the conditions when measuring and changes due to aged deterioration on the vehicle, causing false diagnosis. Therefore determine comprehensively where the malfunction occurs among the input systems, output systems, and the PCM.

Factory service manual diagram




Factory service manual diagram




Factory service manual diagram




Factory service manual diagram




Factory service manual diagram




Factory service manual diagram




Factory service manual diagram




Factory service manual diagram




*1
AT
*2
MT
*3
With cruise control system

Inspection Using An Oscilloscope (Reference)

Throttle control (+) signal

Factory service manual diagram




PCM terminals
- 2A (+)-Negative battery terminal (-)

Oscilloscope setting
- 5 V/DIV (Y), 1 ms/DIV (X), DC range

Vehicle condition
- Idle (Accelerator pedal released)

Throttle control (-) signal

Factory service manual diagram




PCM terminals
- 2B (+)-Negative battery terminal (-)

Oscilloscope setting
- 5 V/DIV (Y), 1 ms/DIV (X), DC range

Vehicle condition
- Idle (Accelerator pedal released)

Purge control signal

Factory service manual diagram




PCM terminals
- 2C (+)-Negative battery terminal (-)

Oscilloscope setting
- 2 V/DIV (Y), 0.1 s/DIV (X), DC range

Vehicle condition
- Idle after warm-up

OCV control signal

Factory service manual diagram




PCM terminals
- 2E (+)-Negative battery terminal (-)

Oscilloscope setting
- 2.5 V/DIV (Y), 1 ms/DIV (X), DC range

Vehicle condition
- Idle after warm-up

CMP signal

Factory service manual diagram




PCM terminals
- 2S (+)-Negative battery terminal (-)

Oscilloscope setting
- 2 V/DIV (Y), 50 ms/DIV (X), DC range

Vehicle condition
- Idle after warm-up

CKP signal

Factory service manual diagram




PCM terminals
- 2W (+)-Negative battery terminal (-)

Oscilloscope setting
- 2 V/DIV (Y), 10 ms/DIV (X), DC range

Vehicle condition
- Idle after warm-up

Generator field coil control signal

Factory service manual diagram




PCM terminals
- 2AI (+)-Negative battery terminal (-)

Oscilloscope setting
- 0.5 V/DIV (Y), 1 ms/DIV (X), DC range

Vehicle condition
- Idle after warm-up

Generator output voltage signal

Factory service manual diagram




PCM terminals
- 2AJ (+)-Negative battery terminal (-)

Oscilloscope setting
- 2 V/DIV (Y), 1 ms/DIV (X), DC range

Vehicle condition
- Idle after warm-up

Ignition timing signals

Factory service manual diagram




PCM terminals
- IGT1 (No.1): 2BA (+)-Negative battery terminal (-)
- IGT2 (No.2): 2AW (+)-Negative battery terminal (-)
- IGT3 (No.3): 2AX (+)-Negative battery terminal (-)
- IGT4 (No.4): 2AT (+)-Negative battery terminal (-)

Oscilloscope setting
- 2 V/DIV (Y), 50 ms/DIV (X), DC range

Vehicle condition
- Idle after warm-up

Fuel injection signals

Factory service manual diagram




PCM terminals
- Fuel Injection No.1: 2BB (+)-Negative battery terminal (-)
- Fuel Injection No.2: 2BC (+)-Negative battery terminal (-)
- Fuel Injection No.3: 2BD (+)-Negative battery terminal (-)
- Fuel Injection No.4: 2AZ (+)-Negative battery terminal (-)

Oscilloscope setting
- 10 V/DIV (Y), 10 ms/DIV (X), DC range

Vehicle condition
- Idle after warm-up

A/F sensor heater control signal

Factory service manual diagram




PCM terminals
- 2BG (+)-Negative battery terminal (-)

Oscilloscope setting
- 5 V/DIV (Y), 50 ms/DIV (X), DC range

Vehicle condition
- Idle after warm-up (no load)

Using the M-MDS

NOTE:
- PIDs for the following parts are not available on this model. Go to the appropriate inspection part.

- CMP sensor
- Main relay

1. Connect the SST(M-MDS) to the DLC-2.

Factory service manual diagram





2. Turn the ignition switch to ON position.

3. Measure the PID value.

- If PID value is not within the specification, follow the instructions in "Inspection item (s)" column.

NOTE:
- The PID/DATA MONITOR function monitors the calculated value of the input/output signals in the PCM. Therefore, an output device malfunction is not directly indicated as a malfunction of the monitored value for the output device. If a monitored value of an output device is out of specification, inspect the monitored value of the input device related to the output control.
- For input/output signals except those of the monitoring items, use a voltmeter to measure the PCM terminal voltage.
- The simulation items that are used in the ENGINE CONTROL SYSTEM OPERATION INSPECTION are as follows.

- ACCS, ALTF, ARPMDES, EVAPCP, FAN1, FAN2, FAN3, FP, FUELPW1, GENVDSD, HTR11, HTR12, IMTV, INJ_1, INJ_2, INJ_3, INJ_4, SEGRP, test, VT DUTY1 Wt

PID/DATA monitor table (reference)

Factory service manual diagram




Factory service manual diagram




Factory service manual diagram




Factory service manual diagram




Factory service manual diagram




Factory service manual diagram




Factory service manual diagram




Factory service manual diagram




Factory service manual diagram




*1
MT
*2
California emission regulation applicable model
*3
AT
*4
With cruise control system

Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.