2011 Mazda 3 Mazdaspeed, 2.3 4FACTORY OEM SERVICE PROCEDURE

Advanced Keyless Entry And Push Button Start System

IMMOBILIZER SYSTEM (ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM) DIAGNOSTIC TROUBLE CODE (DTC) LIST

DTC PCM Description Reference
B10D9:87 P1260:00 Communication error with coil antenna (See SECURITY LIGHT: 11, DTC: B10D9:87/P1260:00 [IMMOBILIZER SYSTEM (ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM)] ).
B10D5:13 P1260:00 Coil antenna malfunction (See SECURITY LIGHT: 12, DTC: B10D5:13/P1260:00 [IMMOBILIZER SYSTEM (ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM)] ).
B10D7:05 P1260:00 Key ID number error (See SECURITY LIGHT: 13, DTC: B10D7:05/PI 260:00 [IMMOBILIZER SYSTEM (ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM)] ).
B1007:94 P1260:00 (See SECURITY LIGHT: 13, DTC: B10D7:94/P1260:00 [IMMOBILIZER SYSTEM (ADVANCED KEYLESS ENTRY AND PUSHBUTTON START SYSTEM)] ).
B10D7:81 P1260:00 Receiving erratic serial data (See SECURITY LIGHT: 14, DTC: B10D7:81/P1260:00 [IMMOBILIZER SYSTEM (ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM)] ).
B10D7:51 P1260:00 Unprogrammed key ID number (See SECURITY LIGHT: 15, DTC: B10D7:51/P1260:00 [IMMOBILIZER SYSTEM (ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM)] ).
U0100:87 P 1260:00 Communication error with PCM (No response) (See SECURITY LIGHT: 16, DTC: U0100:87/P1260:00 [IMMOBILIZER SYSTEM (ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM)] ).
B10D8:00 P1260:00 Shortage of programmed key (See SECURITY LIGHT: 21, DTC: B10D8:00/P1260:00 [IMMOBILIZER SYSTEM (ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM)] ).
B10DA:51 P1260:00 Communication error with PCM (Data transfer failure) (See SECURITY LIGHT: 22, DTC: B10DA:51/P 1260:00 [IMMOBILIZER SYSTEM (ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM)] ).
B10DA:62 P1260:00 Communication error with PCM (Data mismatch) (See SECURITY LIGHT: 23, DTC: B10DA:62/P1260:00 [IMMOBILIZER SYSTEM (ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM)] ).
B10E6:11 - Short to ground in coil antenna power supply circuit (See SECURITY LIGHT: NOT ILLUMINATED, DTC B10E6:11/- [IMMOBILIZER SYSTEM (ADVANCED KEYLESS ENTRY AND PUSHBUTTON START SYSTEM)] ).
B10E6:12 - Short to power supply in coil antenna power supply circuit (See SECURITY LIGHT: NOT ILLUMINATED, DTC B10E6:12/- [IMMOBILIZER SYSTEM (ADVANCED KEYLESS ENTRY AND PUSHBUTTON START SYSTEM)] ).
U0001:88 U0073.00 Keyless contra) module communication error (HS-CAN) (See FOREWORD [MULTIPLEX COMMUNICATION SYSTEM] ).
U0100:00 - Communication error with PCM
U3000:49 - Keyless control module internal malfunction (See DTC U3000:49 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] ).
U3000:96 - Keyless control module internal malfunction (See DTC U3000:96 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] ).
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.