Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2011 Mazda 3 Mazdaspeed, 2.3 3FACTORY OEM SERVICE PROCEDURE
Using the M-MDS
NOTE:
- PIDs for the following parts are not available on this model. Perform the specific inspections for the following parts:
- CMP sensor (See CAMSHAFT POSITION (CMP) SENSOR INSPECTION ).
- Main relay
- Connect the M-MDS to the DLC-2.
- Switch the ignition to ON.
- Measure the PID value.
- If PID value is not within the specification, follow the instructions in the "Inspection item" column.NOTE:
- The PID/DATA MONITOR function monitors the calculated value of the input/output signals in the PCM. Therefore, an output device malfunction is not directly indicated as a malfunction of the monitored value for the output device. If a monitored value of an output device is out of specification, inspect the monitored value of the input device related to the output control.
- For input/output signals except those of the monitoring items, use a voltmeter to measure the PCM terminal voltage.
- The simulation items that are used in the ENGINE CONTROL SYSTEM OPERATION INSPECTION are as follows.
- ACCS, ALTF, ARPMDES, EVAPCP, EVAPCV, FAN_DUTY, FP, IMRC, INJ_1, INJ_2, INJ_3, INJ_4, SEGRP, TEST, VT DUTY, wt, WGC
PID/DATA MONITOR TABLE (REFERENCE)Monitor item (Definition) Unit/Condition Condition/Specification (Reference) Inspection item PCM terminal AAT (Ambient air temperature) °C °F Switch the ignition to ON: Indicates the ambient air temperature - IAT sensor
1M AC_REQ (A/C request signal) OFF/ON A/C switch OFF: OFF
A/C switch ON: ONPerform applicable
DTC troubleshooting- ACCS (A/C relay) OFF/ON A/C relay OFF: OFF
A/C relay ON: ON- The following PIDs:
- RPM, TP REL, ECT
- A/C relay
1I AFR (Air/fuel ratio) - Target air-fuel ratio is displayed - A/F sensor
2Z
2AC
2ADAFR_ACT (Actual air/fuel ratio) - Actual air-fuel ratio is displayed - A/F sensor
2Z
2AC
2ADALTF (Generator field coil control duty value) % Switch the ignition to ON: 0% Idle: 0-100%
Just after A/C switch ON and fan switch ON at idle: Duty value rises- The following PIDs:
- IAT, ECT, RPM, VPWR, ALTT V
- Generator
1AW ALTT V (Generator output voltage) V Idle (no E/L): Approx. 14 V (This is an internal calculation value and differs from the terminal voltage). - Generator
1AX APP1 (APP sensor No. 1) % Accelerator pedal is released: Approx. 8%
Accelerator pedal is depressed: Approx. 68%- APP sensor
1Y V Accelerator pedal is released: Approx. 0.4 V
Accelerator pedal is depressed: Approx. 3.4 VAPP2 (APP sensor No. 2) % Accelerator pedal is released: Approx. 8%
Accelerator pedal is depressed: Approx. 68%- APP sensor
1AC V Accelerator pedal is released: Approx. 0.4 V
Accelerator pedal is depressed: Approx. 3.4 VARPMDES (Target engine speed) RPM Indicate the target engine speed - The following PIDs:
- IAT, RPM, MAP, ECT, MAF, TP REL, ING EAR, ALTT V
- BARO (Barometric pressure) Pa Indicate the BARO - BARO sensor
- V Switch the ignition to ON at sea level: Approx. 4.0 V BAT (Boost air temperature) °C °F Indicate the boost air temperature - MAP/boost air temperature sensor
2N V Boost air temperature 20°C {68°F}: 2.4-2.6 V Boost air temperature 30°C {86 CF}: 1.7-1.9 V BOO (Brake switch) OFF/ON Brake pedal depressed: ON Brake pedal released: OFF - Brake switch No. 1
1AB BRA (Brake pressure applied switch) OFF/ON Brake pedal depressed: ON Brake pedal released: OFF - Brake switch No. 2
- CATT11_DSD (Estimated catalytic converter temperature) °C °F Indicates the estimated catalytic converter temperature - Perform applicable DTC troubleshooting.
- CHRGLP (Generator warning light) OFF/ON Switch the ignition to ON: ON Idle: OFF - Perform applicable DTC troubleshooting.
- COLP (Refrigerant pressure sensor) OFF/ON Refrigerant pressure is more than the specification: ON
Refrigerant pressure is less than the specification: OFF- Refrigerant pressure sensor
- CPP (Clutch pedal position) OFF/ON Clutch pedal depressed: ON Clutch pedal released: OFF - Clutch switch
1D CPP/PNP (Shift lever position) OFF/ON Neutral position: ON Others: OFF - Neutral switch
IS ECT (Engine coolant temperature No. 1) °C °F Indicate the ECT - ECT sensor No. 1
2AH V ECT 20°C {68°F}: 3.04-3.14 V
ECT 60°C {140°F}: 1.29-1.39 VECT2 (Engine coolant temperature No. 2) °C °F Indicate the ECT No. 2 - ECT sensor No. 2
2AP V ECT 20°C {68°F}: 3.04-3.14 V ECT 80°C {176°F}: 0.76-0.83 V EQ_RAT11 (Equivalence ratio (lambda)) - Idling after warm-up: Approx. 1 - Perform applicable DTC troubleshooting.
- EQ_RAT11_DSD (Desired equivalence ratio (lambda)) - Idling after warm-up: Approx. 1 - Perform applicable DTC troubleshooting.
- ETC_ACT (Electronic throttle control actual) ° Indicates the desired TP by angle - Perform applicable DTC troubleshooting.
2A
2BETC_DSD (Electronic throttle control desired) % Indicates the desired TP by percent - The following PIDs:
- APP1, APP2, ETC_ACT
- TP sensor
- ° Indicates the desired TP by angle EVAPCP (Purge solenoid valve duty value) % Switch the ignition to ON: 0%
Idle: 0%- The following PIDs:
- IAT, RPM, ECT, MAF, O2S11, BARO, INGEAR, VPWR
- Purge solenoid valve
2AB EVAPCV (Evaporative emission canister vent valve) OFF/ON Simulation item (EVAPCV) is ON: ON - CV solenoid valve
1AS FAN_DUTY (Fan duty cycle) % ECT less than 98°C {208°F}: 0%
ECT more than 110°C {230°F}: 90%- Fan control module
1AE FCL (Fuel cap warning light) OFF/ON - Fuel cap warning light not illuminated: OFF
- Fuel cap warning light illuminated: ON
- Perform applicable DTC troubleshooting.
- FIA (Fuel injection amount) - Indicates the fuel injection amount. - Fuel injector
- Fuel Injector relay
- FLI (Fuel level) % Fuel gauge level F: Approx. 100%
Fuel gauge level E: Approx. 0%- Perform applicable DTC troubleshooting.
- FP (Fuel pump relay) OFF/ON Idle: ON Cranking: ON - The following PIDs:
- RPM
- Fuel pump relay
1H FP_Hi_PRES (High pressure fuel pump) Off/On Spill valve control solenoid valve work: On Spill valve control solenoid valve don't work: Off - High pressure fuel pump
2F
2GFTP (Fuel tank pressure sensor) Pa Indicate the fuel tank pressure - Fuel tank pressure sensor
1AG V Fuel tank pressure is equal to barometric pressure: approx. 2.6 V FUEL_P_DSD (Fuel pressure desired) Pa Indicate the target fuel pressure. - The following PIDs:
- ECT, FUEL PRES, MAF, RPM, VPWR,
- FUEL_PRES (Fuel pressure sensor) Pa Idle: Approx. 3 MPa
Load 60% or more: Approx. 11.5 MPa- Fuel pressure sensor
2R V Idle: Approx. 1.4 V FUELPW (Fuel injector duration) sec Idle: Approx. 450-650 μs - The following PIDs:
- ECT, IAT, RPM, TP REL, MAF, O2S11, O2S12, MAP, VSS, BOO, AC_REQ, VPWR
2AZ
2BB
2BC
2BDFUELSYS (Fuel system status) OL/CU OL-Drive/OL-Fault/CL-Fault Switch the ignition to ON: OL_Drive Idle (after warm up): CL - The following PIDs:
- IAT, MAF, TP REL, MAP, ECT, RPM, O2S11, O2S12, INGEAR, VPWR, ALTT V
- Fuel injector
- HTR11 (A/F sensor heater) OFF/ON Idle (after warm up): ON<==>OFF - The following PIDs:
- IAT, MAF, TP REL, ECT, RPM
- A/F sensor heater
2C HTR12 (HO2S heater) OFF/ON Idle: ON
Engine speed is above 4, 000 rpm: OFF- The following PIDs:
- IAT, MAF, ECT, RPM
- HO2S heater
2D IAT (Intake air temperature) °C °F Indicate the IAT - MAF/IAT sensor
1M V IAT 20°C {68°F}: 2.4-2.6V IAT 30°C {86°F}: 1.7-1.9V IMRC (Variable swirl solenoid valve) OFF/ON Engine speed is below Approx. 3, 250 rpm and ECT is below 0°C {32°F}: ON
Others: OFF- The following PIDs:
- TP REL, ECT, RPM
- Variable swirl solenoid valve
2AS INGEAR (Load/no load condition) OFF/ON Driving range: ON
Except above: OFF
Others: ON- Perform applicable DTC troubleshooting.
- IVS (CTP condition) Idle/Off Idle APP closed: Idle Others: Off Idle - Perform applicable DTC troubleshooting.
- KNOCKR (Knocking retard) ° Switch the ignition to ON: 0 ° Idle: 0 ° - KS
2U
2VLOAD (Engine load) % Switch the ignition to ON: 0%
Idle (after warm up): 17.1-18.5%
Engine speed is 2, 500 rpm: 14.2-15.2- MAF/IAT sensor
- LONGFT1 (long term fuel trim) % Idle (after warm up):-14-14% - Perform applicable DTC troubleshooting.
- MAF (Mass airflow) g/sec Indicate the MAF - MAF/IAT sensor
1AK V Switch the ignition to ON: Approx. 0.7 V Idle (after warm up): Approx. 1.3 V MAP (Manifold absolute pressure) Pa Indicate the MAP - MAP sensor
2AG V Switch the ignition to ON: Approx. 1.9V Idle (after warm up): Below 1.0 V MIL (Malfunction indicator lamp) OFF/ON Switch the ignition to ON: ON
Idle: OFF- Perform applicable DTC troubleshooting.
- MIL_DIS (Traveled distance since the MIL illuminated) km mile No DTC: 0 km {0 mile} DTC detected: Not 0 km {0 mile} - Perform applicable DTC troubleshooting.
- O2S11 (A/F sensor) A Idle (after warm up): -1.0-1.0 A Deceleration (after warm up): 0.25 A or more - A/F sensor
2Z
2AC
2ADO2S12 (HO2S) V Idle: 0-1 V - HO2S
2Q RO2FT1 (HO2S fuel trim) % - Idle after warm-up: Approx. 0.2
- The following PID
- O2S12
2Q RPM (Engine speed) RPM Indicates the engine speed - CKP sensor
2W SCCS (Speed control command switch) V OFF switch pressed in: Approx. 0 V CANCEL switch pressed in:
Approx. 1.4 V
SET/- switch pressed in: Approx. 2.4 V
RES/+ switch pressed in: Approx. 3.9 V
ON switch pressed in: Approx. 4.3 V
Except above: Approx. 4.7 V- Cruise control switch
1AQ SEGRP (EGR valve (stepping motor) position) - Idle: 0
Engine speed is 1, 187-4200 rpm: 0-57- The following PIDs:
- MAF, TP REL, ECT, RPM, VSS
- EGR valve
2AM
2AN
2AQ
2ARSEGRP DSD (Desired EGR valve (stepping motor) position) % Indicate the desired EGR valve position - The following PIDs:
- MAF, TP REL, ECT, RPM, VSS
- SHRTFT1 (Short term fuel trim [A/F sensor]). % Idle (after warm up): Approx.-30-25% - Perform applicable DTC troubleshooting.
- SPARKADV (Ignition timing) ° Indicate the ignition timing - The following PIDs:
- MAF, TP REL, ECT, RPM, INGEAR, VPWR
- Ignition coil
2AT
2AW
2AX
2BATest (Test mode) OFF/ON Test mode ON: On Test mode OFF: Off - - THM_1 (Thermostat monitor engine coolant temperature No. 1) °C °F Indicates engine coolant temperature No. 1 when thermostat monitoring is finished Thermostat - THM_2 (Thermostat monitor engine coolant temperature No. 2) °C °F Indicates engine coolant temperature No. 2 when thermostat monitoring is finished Thermostat - THM_MAX_2 (Thermostat monitor engine coolant temperature No. 2 max limit) °C °F Indicates upper limit of engine coolant temperature No. 2 for thermostat monitoring execution Thermostat - THM_MIN_1 (Thermostat monitor engine coolant temperature No. 1 min limit) °C °F Indicates lower limit of engine coolant temperature No. 1 for thermostat monitoring execution Thermostat - THM_MIN_2 (Thermostat monitor engine coolant temperature No. 2 min limit) °C °F Indicates lower limit of engine coolant temperature No. 2 for thermostat monitoring execution Thermostat - TP REL (Relative TP) % Switch the ignition to ON (after warm up) APP is released: Approx. 5% APP is depressed: Approx. 5 % NOTE:- When the ignition switch is in the ON position (engine is off), the throttle valve is fully closed regardless of the accelerator pedal opening angle.
- TP sensor
2AK
2ALTP1 (TP sensor No. 1) % Switch the ignition to ON (after warm up) APP is released: Approx. 15 % APP is depressed: Approx. 15 % NOTE:- When the ignition switch is in the ON position (engine is off), the throttle valve is fully closed regardless of the accelerator pedal opening angle.
- TP sensor
2AK V Switch the ignition to ON (after warm up)
APP is released: Approx. 0.85 V
APP is depressed: Approx. 0.85 VTP2 (TP sensor No. 2) % Switch the ignition to ON (after warm up)
APP is released: Approx. 15 %
APP is depressed: Approx. 15 %NOTE:- When the ignition switch is in the ON position (engine is off), the throttle valve is fully closed regardless of the accelerator pedal opening angle.
- TP sensor
2AL V Switch the ignition to ON (after warm up) APP is released: Approx. 4.15 V
APP is depressed: Approx. 4.15 VTPCT (Lowest closed throttle voltage) V Switch the ignition to ON: Approx 0.5 V - TP sensor
2AK
2ALVPWR (Battery positive voltage) V Indicates the battery voltage - Battery
1BA VSS (Vehicle speed) KPH MPH Indicates the vehicle speed - Perform applicable DTC troubleshooting.
- VTACT1 (Actual valve timing) ° Idle: Approx. 0° - CMP sensor
- CKP sensor
2S
2WVT DIFF1 (Difference between actual valve timing and target valve timing) ° Idle: Approx. 0° - The following PIDs:
- RPM, LOAD, VT ACT1
- CMP sensor
- VT DUTY1 (Camshaft position commanded duty cycle) % Idle: Approx. 11.5% - The following PIDs:
- TP REL, ECT, RPM
- OCV
2AF WGC (Wastegate control solenoid valve) % Racing with the accelerator pedal fully depressed: 10-100 % - Wastegate control solenoid valve
2AA Fully closed: 0 % - If PID value is not within the specification, follow the instructions in the "Inspection item" column.
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
