2011 Mazda 3 Mazdaspeed, 2.3 3FACTORY OEM SERVICE PROCEDURE

Inspection Using An Oscilloscope (Reference)

APP sensor (No. 2) signal 

Accelerator pedal released 

Fig 1: APP Sensor (No. 2) Signal Waveform (Released)
G07868443Courtesy of MAZDA MOTORS CORP.

Accelerator pedal depressed 

PCM terminals 

  • 1AC (+)-body ground (-)

Oscilloscope setting 

  • 5 V/DIV (Y), 5 ms/DIV (X), DC range

Vehicle condition 

  • Idle after warm up
    Fig 2: APP Sensor (No. 2) Signal Waveform (Depressed)
    G07868444Courtesy of MAZDA MOTORS CORP.

Fan control module signal 

PCM terminals 

  • 1AE (+)-body ground (-)

Oscilloscope setting 

  • 5 V/DIV (Y), 5 ms/DIV (X), DC range

Vehicle condition 

Idle after warm up 

Fig 3: Fan Control Module Signal Waveform
G07868445Courtesy of MAZDA MOTORS CORP.

Generator field coil control signal 

PCM terminals 

  • 1AW (+)-body ground (-)

Oscilloscope setting 

  • 0.5 V/DIV (Y), 2 ms/DIV (X), DC range

Vehicle condition 

  • Idle after warm up
    Fig 4: Generator Field Coil Control Signal Waveform
    G07868446Courtesy of MAZDA MOTORS CORP.

Generator output voltage signal 

PCM terminals 

  • 1AX (+)-body ground (-)

Oscilloscope setting 

  • 2 V/DIV (Y), 1 ms/DIV (X), DC range

Vehicle condition 

  • Idle after warm up
    Fig 5: Generator Output Voltage Signal Waveform
    G07868447Courtesy of MAZDA MOTORS CORP.

A/F sensor heater control signal 

PCM terminals 

  • 2C (+)-body ground (-)

Oscilloscope setting 

  • 5 V/DIV (Y), 200 ms/DIV (X), DC range

Vehicle condition 

  • Idle after warm up
    Fig 6: A/F Sensor Heater Control Signal Waveform
    G07868448Courtesy of MAZDA MOTORS CORP.

CMP sensor signal 

PCM terminals 

  • 2S (+)-body ground (-)

Oscilloscope setting 

  • 2 V/DIV (Y), 100 ms/DIV (X), DC range

Vehicle condition 

  • Idle after warm up
    Fig 7: CMP Sensor Signal Waveform
    G07868449Courtesy of MAZDA MOTORS CORP.

CKP sensor signal 

PCM terminals 

  • 2W (+)-body ground (-)

Oscilloscope setting 

  • 2 V/DIV (Y), 5 ms/DIV (X), DC range

Vehicle condition 

  • Idle after warm up
    Fig 8: CKP Sensor Signal Waveform
    G07868450Courtesy of MAZDA MOTORS CORP.

Wastegate control solenoid valve signal 

PCM terminals 

  • 2AA (+)-body ground (-)

Oscilloscope setting 

  • 20 V/DIV (Y), 20 ms/DIV (X), DC range

Vehicle condition 

  • Switch the ignition to ON
    Fig 9: Wastegate Control Solenoid Valve Signal Waveform
    G07868451Courtesy of MAZDA MOTORS CORP.

Purge control signal 

PCM terminals 

  • 2AB (+)-body ground (-)

Oscilloscope setting 

  • 10 V/DIV (Y), 20 ms/DIV (X), DC range

Vehicle condition 

  • Racing
    Fig 10: Purge Control Signal Waveform
    G07868452Courtesy of MAZDA MOTORS CORP.

OCV signal 

PCM terminals 

  • 2AF (+)-body ground (-)

Oscilloscope setting 

  • 5 V/DIV (Y), 1 ms/DIV (X), DC range

Vehicle condition 

  • Racing
    Fig 11: OCV Signal Waveform
    G07868453Courtesy of MAZDA MOTORS CORP.

IGT1, IGT2, IGT3, IGT4 control signals 

PCM terminals 

  • IGT1 (No. 1): 2BA (+)-body ground (-)
  • IGT2 (No. 2): 2AW (+)-body ground (-)
  • IGT3 (No. 3): 2AX (+)-body ground (-)
  • IGT4 (No. 4): 2AT (+)-body ground (-)

Oscilloscope setting 

  • 2 V/DIV (Y), 20 ms/DIV (X), DC range

Vehicle condition 

  • Idle after warm up
    Fig 12: IGT1, IGT2, IGT3, IGT4 Control Signals Waveform
    G07868454Courtesy of MAZDA MOTORS CORP.

Fuel injection control (-) 

PCM terminals 

  • Fuel injection No. 1: 2BB (+)-body ground (-)
  • Fuel injection No. 2: 2BC (+)-body ground (-)
  • Fuel injection No. 3: 2BD (+)-body ground (-)
  • Fuel injection No. 4: 2AZ (+)-body ground (-)
    Fig 13: Fuel Injection Control (-) Signal Waveform
    G07868455Courtesy of MAZDA MOTORS CORP.

Oscilloscope setting 

  • 10 V/DIV (Y), 20 ms/DIV (X), DC range

Vehicle condition 

  • Idle after warm up

Fuel injection control (+) 

PCM terminals 

  • Fuel injection No. 1, No. 4: 2BG (+)-body ground (-)
  • Fuel injection No. 2, No. 3: 2BH (+)-body ground (-)

Oscilloscope setting 

  • 20 V/DIV (Y), 400 ÎĽs/DIV (X), DC range

Vehicle condition 

  • Idle after warm up
    Fig 14: Fuel Injection Control (+) Signal Waveform
    G07868456Courtesy of MAZDA MOTORS CORP.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.