Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2011 Mazda 2 L4-1.5LFACTORY OEM SERVICE PROCEDURE
Repair and Diagnosis: Technical Service Bulletins
- How to Find Technical Service Bulletins by Category/Symptom
- Customer Interest
- Interior - Driver Seat Rattle When Starting Or Stopping
- Steering - Steering Wheel Off Center When Driving Straight
- Steering - Rattle Noise From Steering System At Low Speeds
- Restraints - Air Bag Lamp ON/DTC B00A0:81 Set
- Steering/Suspension - Steering Wheel Off-Center
- Body - Front Mud Guard Fastener Broken By Snow Weight
- Fuel System - MIL ON/DTC P0451:00 Set
- Body - Rattle Noise From Base Of Windshield
- Suspension - Creak/Squeak From Rear On Bumps
- Cooling System - MIL ON/DTC P0128 Set
- Audio System - No Sound Output When Cold
- Restraints - Front Seat Belt Adjuster Rattles
- Interior - Rattle From Door Panel(s) With High Audio Vol
- Exhaust System - Squeak Noise Heard With Engine Idling
- Steering - Steering Wheel Off Center, No Pull Or Drift
- Superceded Bulletins
- 0905310 - 12/06/10
- Lighting - Excessive Water/Condensation In Headlamps
- Lighting - Condensation In Front/Rear Lamps
- Body - Paint Damage Repair Guide
- Restraints - Passenger Air Bag Deactivation Lamp ON
- Suspension - Strut/Shock Replacement Guidelines
- Suspension - Squeak/Creak From Rear On Bumps
- Electrical - Battery Testing Procedures
- A/T - Cooler/Line Flushing Procedure
- Engine Controls - Mass Air Flow Sensor Insp. Procedure
- A/T - Correct Fluid Applications
- All Technical Service Bulletins
- Interior - Driver Seat Rattle When Starting Or Stopping
- Engine Controls - Mass Air Flow (MAF) Sensor Inspection
- Interior - Poor Upper Dash Surface Appearance
- Steering - Steering Wheel Off Center When Driving Straight
- Restraints - Passenger Air Bag Indicator (PAD) Information
- Electrical - Battery Maintenance Information
- Electrical - Battery Testing Procedures
- Steering - Rattle Noise From Steering System At Low Speeds
- ABS/TCS/DSC - Clunk/Bang/Jolt From Front Of Vehicle At Take-Off
- Body - Paint Damage Repair Guide
- Exhaust System - Excessive Sulfur Odors
- Restraints - Air Bag Lamp ON/DTC B00A0:81 Set
- Steering/Suspension - Steering Wheel Off-Center
- Brakes - Judder/Dragging Diagnostic Information
- Body - Front Mud Guard Fastener Broken By Snow Weight
- A/T - Cooler Line Flushing Procedures
- Fuel System - MIL ON/DTC P0451:00 Set
- Body - Rattle Noise From Base Of Windshield
- Tire Monitor System - Service Precaution
- Instruments - Ambient Temperature Display Inaccurate
- A/T - Diagnostic Procedures
- Suspension - Creak/Squeak From Rear On Bumps
- Cooling System - MIL ON/DTC P0128 Set
- A/C - Poor Blower Motor Performance
- Electrical - Battery Maintenance
- Audio System - No Sound Output When Cold
- Restraints - Front Seat Belt Adjuster Rattles
- Keyless Entry - Transmitter Battery Replacement Cautions
- Body - Liftgate Won't Open/Close Properly
- Interior - Rattle From Door Panel(s) With High Audio Vol
- Suspension - Shock Absorber/Strut Replacement Guidelines
- Lighting - Condensation In Front/Rear Combination Lamps
- Exhaust System - Squeak Noise Heard With Engine Idling
- Lighting - Excessive Condensation In Headlamps
- Steering - Steering Wheel Off Center, No Pull Or Drift
- A/T - ATF Applications
- Interior - Proper Floor Mat Usage And Installation
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.