Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2010 Mazda 5 Sport, 2.3 L, StandardFACTORY OEM SERVICE PROCEDURE
Using SST (M-MDS)
NOTE:
- PIDs for the following parts are not available on this model. Go to the appropriate part inspection information
.
- CMP sensor (See CAMSHAFT POSITION (CMP) SENSOR INSPECTION .)
- Main relay (See RELAY INSPECTION .)
- Connect the SST (M-MDS) to the DLC-2.
- Turn the ignition switch to ON position.
- Measure the PID value.
- If PID value is not within the specification, follow the instructions in Action column.NOTE:
- The PID/DATA MONITOR function monitors the calculated value of the input/output signals in the PCM. Therefore, an output device malfunction is not directly indicated as a malfunction of the monitored value for the output device. If a monitored value of an output device is out of specification, inspect the monitored value of the input device related to the output control.
- The simulation items that are used in the ENGINE CONTROL SYSTEM OPERATION INSPECTION are as follows.
- ACCS, ALTR ARPMDES, EVAPCP, FAN_DUTY, FR FUELPW1, GENVDSD, HTR11, HTR12, IMRC, IMTV, INJ_1, INJ_2, INJ_3, INJ_4, SEGRR test, VT DUTY1 Wt
REFERENCEItem (definition) Unit/Condition Condition/Specification (Reference) Inspection item(s) PCM terminal AAT (Ambient air temperature) °C °F - Indicates ambient air temperature
- The following PIDs
- IAT
- AC_REQ (Refrigerant pressure switch (low pressure switch, high pressure switch)) On/Off - Refrigerant pressure is more than the specification or less than the specification. (Refrigerant pressure switch (low pressure switch, high pressure switch) is off.): Off
- Others: On
- Refrigerant pressure switch (low pressure switch, high pressure switch)
1AW ACCS (A/C relay) On/Off - A/C is operating: On
- A/C is not operating: Off
- The following PIDs
- CPR CPP/PNR ECT, RPM, TP REL, AC_REQ, COLP
1I AFR (Air/fuel ratio) - - Target air-oil ratio is displayed
- A/F sensor
2Z
2AC
2ADAFR_ACT (Actual air/fuel ratio) - - Actual air-oil ratio is displayed
- A/F sensor
2Z
2AC
2ADALTF (Generator field coil control duty value) % - Ignition switch is turned to the ON position: 0%
- Idling, E/L is operating: Duty value increases.
- The following PIDs
- ECT, IAT, RPM, VSS, ALTT V, VPWR
- Generator
2AA ALTT V (Generator output voltage) V - Ignition switch is turned to the ON position: Approx. 1.0 V or less
- Idling (no electrical load): Approx. 14 V (This is an internal calculation value and differs from the terminal voltage.)
- Generator
2AF APP (Accelerator pedal position) % - Accelerator pedal released: 0%
- Accelerator pedal depressed: 100%
- The following PIDs: APP1, APP2
- APP sensor
1AO
1APAPP1 (Accelerator pedal position) V - Accelerator pedal released: Approx. 0.4 V
- Accelerator pedal depressed: Approx. 3.3 V
- APP sensor
1AP % - Accelerator pedal released: Approx. 8%
- Accelerator pedal depressed: Approx. 65%
APP2 (Accelerator pedal position) V - Accelerator pedal released: Approx. 0.4 V
- Accelerator pedal depressed: Approx. 3.3 V
- APP sensor
1AO % - Accelerator pedal released: Approx. 8%
- Accelerator pedal depressed: Approx. 65%
ARPMDES (Target engine speed) RPM - Idling: indicate the target engine speed
- The following PIDs
- CPP, CPP/PNP, ECT, IAT, RPM, TP REL, MAF, BARO, VSS, AC_REQ, COLP
- BARO (Barometric pressure) kPa Bar psi - Ignition switch is turned to the ON position: Indicate the atmospheric pressure
- BARO sensor
- V BOO (Brake switch) On/Off - Brake pedal is depressed: On
- Brake pedal is released: Off
- Brake switch
1AB BPA (Brake pressure applied switch) On/Off - Brake pedal depressed: Off
- Brake pedal released: On
- - CATT11_DSD (Estimated catalytic converter temperature) °C °F - Idling after warm up: indicate the TWC forecast temperature
- - CHRGLP (Generator warning light) On/Off - Ignition switch ON: On
- Idle: Off
- Perform applicable DTC troubleshooting.
- COLP (Refrigerant pressure switch (medium pressure switch)) ON/OFF - Refrigerant pressure is 1.52 MPa {15.5 kgf/cm2 , 220 psi} or more: On
- Refrigerant pressure is 1.23 MPa {12.5 kgf/cm2 , 178 psi} or less: Off
- Refrigerant pressure switch (medium-pressure switch)
1AX CPP(2) (Clutch pedal position) On/Off - Clutch pedal is depressed: On
- Clutch pedal is released: Off
- CPP switch
1BD CPP/PNP(2) (Shift lever position) Drive/Neutral - Neutral: Neutral
- Other than neutral: Drive
- Neutral switch
1BC DTCCNT (Number of DTC detected) - - Number of DTCs stored
- - ECT (Engine coolant temperature) °C °F - Ignition switch is turned to the ON position: Indicate the ECT
- ECT sensor
2AH V - ECT is 20 °C {68 °F}: 3.04-3.14 V
- ECT is 80°C {176°F}: 0.76-0.83 V
EQ_RAT11 (Equivalence ratio (lambda)) - - Idle (after warm up): Approx. 1
- Perform applicable DTC troubleshooting.
(See DTC TABLE .)
2Z
2AC
2ADEQ_RAT11_DSD (Theoretical air/fuel ratio coefficient to calculate target air/fuel ratio) - - Idling after warm-up: Approx. 1
- A/F sensor
- ETC_ACT (Electronic throttle control actual) ° - Indicate the throttle opening angle
- TP sensor
2BE
2BFETC_DSD (Electronic throttle control desired) % - Indicate the target throttle opening ratio
- TP sensor
- ° - Indicate the target throttle opening angle
- The following PIDs:APP1, APP2, ETC_ACT
- TP sensor
EVAPCP (Purge solenoid valve duty value) % - Ignition switch is turned to the ON position: 0%
- Increase the engine speed: Duty value rises
- The following PIDs
- ECT, IAT, RPM, TP REL, MAF, O2S11, BOO, VPWR
2C FAN_DUTY (Fan control duty value) % - When all of following condition are met: 0-75%
- A/C On
- Idle
- Fun control module
1R FLI (Fuel level) % Fuel gauge level F: Approx. 100%
Fuel gauge level E: Approx. 0%- Perform applicable DTC troubleshooting.
- FP (Fuel pump relay) On/Off - Idling: On
- Cranking: On
- Fuel pump relay
1BG FUELPW (Fuel injector duration) ms - Idling: Approx. 2.3 ms
- The following PIDs
- CPP, CPP/PNP, ECT, IAT, RPM, TP REL, MAF, O2S11, O2S12, BARO, VSS, BOO, AC_REQ, COLP, VPWR
2AZ
2BB
2BC
2BDFUELSYS (Fuel system status) OL/CL/
OL-Drive/
OL-Fault/
CL-Fault- Idling after warm-up: CL
- The following PIDs
- CPP, CPP/PNP, ECT, IAT, RPM, TP REL, MAF, O2S11, O2S12, BARO, VSS, BOO, AC_REQ, COLP, VPWR
- GENVDSD (Target generator voltage) V - Idling (no electrical load): Approx. 14 V (This is an internal calculation value and differs from the terminal voltage.)
- The following PIDs
- ECT, IAT, RPM, VSS, ALTT V, VPWR
- Generator
- HTR11 (A/F sensor heater control) On/Off - Idling after warm-up: On<==>Off
- The following PIDs
- ECT, IAT, RPM, TP REL, MAF, BARO, VPWR
2A HTR12 (HO2S heater control) On/Off - Idling after warm-up: On
- The following PIDs
- ECT, IAT, RPM, TP REL, MAF, BARO, VPWR
2B IAT (Intake air temperature) °C °F - Ignition switch is turned to the ON position: Indicate the IAT
- IAT sensor
1AT V - IAT is 20°C {68°F}: Approx. 2.38 V
- IAT is 60°C {140°F}: Approx. 0.89 V
IMRC (Variable tumble control) On/Off - ECT below 63°C {145°F} and engine speed below 3,750 rpm: On
- ECT above 63°C {145°F} or engine speed above 3,750 rpm: Off
- The following PIDs
- ECT, RPM, TP REL
2I IMTV (Variable intake air control) On/Off - Engine speed is below 4,600 rpm: On
- Engine speed is above 4,600 rpm: Off
- The following PIDs
- RPM
2J INGEAR (Gears are engaged) On/Off MTX - When the following conditions are satisfied: On
- Not neutral
- Clutch pedal released
- Except above: Off
- CPP switch
- Neutral switch
1BD
1BCATX - Driving range: On
- Except above: Off
- TR switch
- IVS (CTP condition) Idle/Off Idle - Idling: Idle
- Other than idling: Off Idle
- The following PIDs
- TP REL
- KNOCKR (Knocking retard) ° - Ignition switch is turned to the ON position: 0 °
- Idling: 0°
- KS
2U
2VLDP_EVAPCP (EVAP system leak detection pump detect incorrect purge flow) A - Indicates EVAP system leak detection pump detect incorrect
- Perform applicable DTC troubleshooting.
- LDP_IDL (EVAP system leak detection pump idle current) A - Indicates EVAP system leak detection pump idle current
- Perform applicable DTC troubleshooting.
- LDP_MON (EVAP system leak detection pump monitoring current) A - Indicates EVAP system leak detection pump monitoring current
- Perform applicable DTC troubleshooting.
- LDP_REF (EVAP system leak detection pump reference current) A - Indicates EVAP system leak detection pump reference current
- Perform applicable DTC troubleshooting.
- LDP_SLDV (EVAP system small leak detection value) A - Indicates EVAP system small leak detection value
- Perform applicable DTC troubleshooting.
- LDP_VSL_FV(3) (EVAP system small leak detection value) mA/sec - Indicates EVAP system small leak detection fail value
- Perform applicable DTC troubleshooting.
- LDP_VSL_SV(3) (EVAP system small leak detection value) mA/sec - Indicates EVAP system small leak detection safe value
- Perform applicable DTC troubleshooting.
- LDP_VSLDV(3) (EVAP system small leak detection value) mA/sec - Indicates EVAP system small leak detection value
- Perform applicable DTC troubleshooting.
- LOAD (Engine load) % - Ignition switch is turned to the ON position: 0%
- Idling after warm-up: Approx. 16%
- The following PIDs
- BARO, IAT, MAF, RPM
- LONGFT1 (Long term fuel trim) % - Idling (after warm-up): Approx. -20-20%
- The following PIDs
- CPP, CPP/PNP, ECT, IAT, RPM, TP REL, MAF, O2S11, O2S12, BARO, VSS, BOO, AC_REQ, COLP, VPWR
- MAF (Mass air flow) g/s - Ignition switch to the ON position: Indicate the MAF
- MAF sensor
1AK V - Ignition switch is turned to the ON position: Approx. 0.7 V
- Idling after warm-up: Approx. 1.2 V
MAP (Manifold absolute pressure) kPa Bar psi - Ignition switch ON (at sea level): Indicate the MAP
- MAP sensor
2AG V - Ignition switch ON (at sea level): Approx. 4.1 V
- Idling after warm-up: Approx. 1.4 V
MIL (Malfunction indicator lamp) On/Off - Ignition switch is turned to the ON position: On
- Idling: Off
(If there is a malfunction in emission control related system: On)
- MIL
- MIL_DIS (Travelled distance since MIL illuminated) km mile Indicate the travelled distance since the MIL illuminated O2S11 (A/F sensor) A - Idling after warm-up: approx. 0 mA
- A/F sensor
2Z
2AC
2ADO2S12 (HO2S) V - Idling after warm-up: 0-1.0 V
- HO2S
2Q RO2FT1 (HO2S fuel trim) - - Idle after warm-up: Approx. 0.2
- The following PID
- O2S12
2Q RPM (Engine speed) RPM - Indicate the engine speed
- CKP sensor
2W SCCS (Cruise control switch) V Press ON/OFF: Approx. 0 V
Press CANCEL: Approx. 1.8 V
Press SET/COAST: Approx. 3.8 V
Press RES/ACCEL: Approx. 4.6 V
Others: Approx. 5.0 V- Cruise control switch.
1AQ SEGRP (EGR control) - - Ignition switch is turned to the ON position: 0 step
- Idling: 0 step
- Cranking: 0-52 step
- EGR valve
2AT
2AW
2AX
2BASEGRP DSD (EGR valve position desired) % - When the PCM control the EGR system: indicate the desired EGR valve position
- The following PID
- MAF, TP REL, ECT, RPM, VSS
- EGR valve
- SHRTFT1 (Short term fuel trim (A/F sensor)) % - Idling (after warm-up): -30- +25%
- The following PIDs
- CPP, CPP/PNP, ECT, IAT, RPM, TP REL, MAF, O2S11, O2S12, BARO, VSS, BOO, AC_REQ, COLP, VPWR
- SHRTFT12(4) (Short term fuel trim (HO2S)) % - Idling after warm-up: Approx. 99%
- The following PIDs
- CPP, CPP/PNP, ECT, IAT, RPM, TP REL, MAF, O2S11, O2S12, BARO, VSS, BOO, AC_REQ, COLP, VPWR
- SPARKADV (Ignition timing) ° (BTDC) - During test mode on at idling: BTDC 9-11 ° (BTDC)
- Idling: BTDC 6-18 ° (BTDC)
- The following PIDs
- CPP, CPP/PNP, ECT, IAT, RPM, TP REL, MAF, KNOCKR, BOO, AC_REQ, COLP
2G
2H
2K
2Ltest (Test mode) On/Off - During test mode: On
- Other than test mode: Off
- - TH_M (Thermostat monitor) - - Indicates heat radiation ratio (heat radiation when thermostat is malfunctioning/heat radiation when thermostat is normal) when thermostat monitoring is finished
- Thermostat
- °C °F - Indicates engine coolant temperature when thermostat monitoring is finished
- TH_M_MAX (Thermostat monitor) - - Indicates upper limit of heat radiation ratio (heat radiation when thermostat is malfunctioning/heat radiation when thermostat is normal) for thermostat monitoring execution
- Thermostat
- °C °F - Indicates upper limit of engine coolant temperature for thermostat monitoring execution
- TH_M_MIN (Thermostat monitor) - - Indicates lower limit of heat radiation ratio (heat radiation when thermostat is malfunctioning/heat radiation when thermostat is normal) for thermostat monitoring execution
- Thermostat
- °C °F - Indicates lower limit of engine coolant temperature for thermostat monitoring execution
- TIRESIZE (Tire revolution per mile) rev/mile - Indicate the tire revolution per a mile
- - TPREL (Throttle position signal (relative value)) % - CTP: Approx. 5%
- WOT: Approx. 80%
- TP sensor
- TP1 (TP sensor 1) V - CTP: Approx. 0.6 V
- WOT: Approx. 4.4 V
- TP sensor
2AK % - Indicates throttle position
TP2 (TP sensor 2) V - CTP: Approx. 4.4 V
- WOT: Approx. 0.6 V
- TP sensor
2AL % - Indicates throttle position
TPCT (TP sensor voltage at CTP) V - Approx. 0.5 V
- TP sensor
2AK
2ALVPWR (Battery positive voltage) V - Ignition switch is turned to the ON position.: B+
- Idling: B+
- Battery
1C VSS (Vehicle speed) KPH MPH - Vehicle running: Indicate the vehicle speed
- VSS
- VT ACT1 (Actual valve timing) ° - Idling: 0 °
- Racing: 0-25 °
- The following PIDs
- ECT, RPM, TP REL, MAF
- OCV
2E VT DIFF1 (Difference between target valve timing and actual valve timing) ° - Idling: 0 °
- The following PIDs
- ECT, RPM, TP REL, MAF
- OCV
2E VT DUTY1 (OCV control) % - Idling: Approx. 11 %
- The following PIDs
- ECT, RPM, TP REL, MAF
2E VTC (Variable tumble control) On/Off - Variable tumble shutter valve switch ON: ON
- Variable tumble shutter valve switch OFF: OFF
- Variable tumble shutter valve switch
2AE(4), 2R(5) (1) The voltage may vary excessively depending on the weather or battery conditions. (2) MTX (3) California emission regulation applicable model (4) TYPE A (5) TYPE B - If PID value is not within the specification, follow the instructions in Action column.
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
