2008 Mazda Mazdaspeed3 L4-2.3L TurboFACTORY OEM SERVICE PROCEDURE

Tightening Torques

[LF, L3]

Factory service manual diagram




Cylinder Head Bolt
Tightening torque
1. 3-11 N-m (30.6-112 kgf-cm, 26.6-97.3 in-lbf)
2. 13-17 N-m (1.4-1.7 kgf-m, 9.59-12.5 ft-lbf)
3. 43-47 N-m (4.4-4.7 kgf-m, 31.8-34.6 ft-lbf)
4. 88°-92°
5. 88°-92°

Factory service manual diagram




Cylinder Head bolt Re-Usability
Measure the length of each cylinder head bolt.
Replace any that exceeds maximum length.
Cylinder Head Bolt Length L 145.2-145.8 mm (5.717-5.740 in)
Cylinder Head Bolt Maximum 146.5 mm (5.767 in)

Factory service manual diagram




Camshaft Cap bolts
Tighten torque
Step 1. 5.0-8.0 N-m (51.0-81.5 kgf-cm, 44.3-70.8 in-lbf)
Step 2. 14-17 N-m (1.5-1.7 kgf-m, 10.4-12.5 ft-lbf)

Exhaust camshaft sprocket lock bolt.
Tightening torque 69-75 N-m (7.1-7.6 kgf-m, 50.9-55.3 ft-lbf)

[L3 WITH TC]

Factory service manual diagram




Cylinder Head Bolt
Tightening procedure
1st step: 3.0-11 N-m (31-112 kgf-cm, 27-97 in-lbf)
2nd step: 13-17 N-m (133-173 kgf-cm, 116-150 in-lbf)
3rd step: 43-47 N-m (4.4-4.7 kgf-m, 32-34 ft-lbf)
4th step: 88°-92°
5th step: 88°-92°

Factory service manual diagram




Cylinder Head Re-Usability
Measure the length of each cylinder head bolt. Replace any cylinder head bolts that exceed the maximum length.
Cylinder head bolt length
Standard: 144.7-145.3 mm (5.697-5.720 in)
Maximum: 146 mm (5.74 in)

Factory service manual diagram




Camshaft Cap Bolts
Install the camshaft caps and temporarily tighten the camshaft cap bolts evenly in two or three passes, and then tighten the camshaft cap bolts using the following two steps, in the order shown in the figure.
Tightening procedure
1st step: 5.0-9.0 N-m (51-91 kgf-cm, 45-79 in-lbf)
2nd step: 14-17 N-m (1.5-1.7 kgf-m, 11-12 ft-lbf)

Exhaust Camshaft Sprocket
Tightening torque 69-75 N-m (7.1-7.6 kgf-m, 51-55 ft-lbf)

Variable valve timing actuator installation bolt
Tightening torque 69-75 N-m (7.1-7.6 kgf-m, 51-55 ft-lbf)
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.