Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2007 Mazda RX8 2RTR-1.3LFACTORY OEM SERVICE PROCEDURE
Barometric Pressure Sensor: Testing and Inspection
BAROMETRIC PRESSURE (BARO) SENSOR INSPECTION
NOTE: Before performing the following inspection, make sure to follow the troubleshooting flowchart. (See FOREWORD.) Foreword
Voltage Inspection
1. Remove the BARO sensor with the connector still connected.
2. Remove the BARO sensor hose.
3. Turn the ignition switch to the ON position.
4. Verify that the voltage at PCM terminal 5S (M-MDS PID: BARO) is within the specification.
- If not within the specification even though the related wiring harnesses have no malfunction, replace the BARO sensor.
BARO sensor output voltage
2.4 - 4.7 V
5. Install the vacuum pump.
6. Verify that the change in voltage at PCM terminal 5S (M-MDS PID: BARO) is within the specification when a vacuum of 30 kPa {0.30 kgf/sq.cm, 4.4 psi} is applied.
- If not within the specification, replace the BARO sensor.
BARO sensor output voltage variance
1.06 - 1.30 V
NOTE: The voltage shown in the figure may vary excessively depending on the weather or battery conditions.

BARO sensor characteristics graph (reference)
Circuit Open/Short Inspection
1. Disconnect the PCM connectors.
2. Disconnect the BARO sensor connector.

3. Inspect the following wiring harnesses for open or short circuit. (Continuity inspection)
Open circuit
- If there is no continuity in the following wiring harnesses, there is an open circuit. Repair or replace the wiring harness.
- BARO sensor terminal A and PCM terminal 5S
- BARO sensor terminal B and PCM terminal 4U
- BARO sensor terminal C and PCM terminal 4K
Short circuit
- If there is continuity in the following wiring harnesses, there is a short circuit. Repair or replace the wiring harness.
- BARO sensor terminal A and body ground
- BARO sensor terminal A and power supply
- BARO sensor terminal C and body ground
- BARO sensor terminal C and power supply
NOTE: Before performing the following inspection, make sure to follow the troubleshooting flowchart. (See FOREWORD.) Foreword
Voltage Inspection
1. Remove the BARO sensor with the connector still connected.
2. Remove the BARO sensor hose.
3. Turn the ignition switch to the ON position.
4. Verify that the voltage at PCM terminal 5S (M-MDS PID: BARO) is within the specification.
- If not within the specification even though the related wiring harnesses have no malfunction, replace the BARO sensor.
BARO sensor output voltage
2.4 - 4.7 V
5. Install the vacuum pump.
6. Verify that the change in voltage at PCM terminal 5S (M-MDS PID: BARO) is within the specification when a vacuum of 30 kPa {0.30 kgf/sq.cm, 4.4 psi} is applied.
- If not within the specification, replace the BARO sensor.
BARO sensor output voltage variance
1.06 - 1.30 V
NOTE: The voltage shown in the figure may vary excessively depending on the weather or battery conditions.
BARO Sensor Characteristics Graph (Reference):
BARO sensor characteristics graph (reference)
Circuit Open/Short Inspection
1. Disconnect the PCM connectors.
2. Disconnect the BARO sensor connector.
3. Inspect the following wiring harnesses for open or short circuit. (Continuity inspection)
Open circuit
- If there is no continuity in the following wiring harnesses, there is an open circuit. Repair or replace the wiring harness.
- BARO sensor terminal A and PCM terminal 5S
- BARO sensor terminal B and PCM terminal 4U
- BARO sensor terminal C and PCM terminal 4K
Short circuit
- If there is continuity in the following wiring harnesses, there is a short circuit. Repair or replace the wiring harness.
- BARO sensor terminal A and body ground
- BARO sensor terminal A and power supply
- BARO sensor terminal C and body ground
- BARO sensor terminal C and power supply
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
