Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2007 Mazda CX-7 L4-2.3L TurboFACTORY OEM SERVICE PROCEDURE
Body - Power Window Auto Open/Close Feature Inoperative
TSB: 09-014/06
2006 MAZDA6, MAZDASPEED6, 2007 CX-7 - POWER WINDOW AUTO OPEN / CLOSE AND ANTI-PINCH FEATURES INOPERATIVE
APPLICABLE MODEL(S)/VINS
2006 Mazda6 and Mazdaspeed6
2007 CX-7
DESCRIPTION

The 2006 Mazda6/Mazdaspeed6 and 2007 CX-7 vehicles are equipped with "Auto Open/Close" and "Anti-Pinch" window features.
This system requires a special "Power Window Initialization Procedure" for these features to operate~ The power window initialization procedure is performed during vehicle production, however, in the following cases the initialization procedure must be performed in order to restore "auto open/close" and "anti-pinch" operation.
^ Battery has been disconnected.
^ Power window fuse has been removed/replaced.
^ Power window initialization procedure was not performed at vehicle production.
NOTE:
TO AVOID UNNECESSARY REPLACEMENT OF THE POWER WINDOW MAIN SWITCH, ALWAYS PERFORM THE "POWER WINDOW INITIALIZATION PROCEDURE" BEFORE REPLACING ANY POWER WINDOW RELATED PARTS.
POWER WINDOW INITIALIZATION PROCEDURE
1. Turn ignition to ON position.

2. From driver's seat ensure window lockout switch is NOT depressed.
3. Press window switch down to fully open door window.

4. Pull window switch up to fully close door window; hold switch up for two (2) seconds; release switch.
5. Move to front passenger seat and repeat Steps 3 - 4 on passenger window switch.
6. Mazdaspeed6 Only: Move to rear seat and repeat Steps 3 - 4 at left and right rear seat window switches.
7. Verify proper window operation using each door switch.

Disclaimer
2006 MAZDA6, MAZDASPEED6, 2007 CX-7 - POWER WINDOW AUTO OPEN / CLOSE AND ANTI-PINCH FEATURES INOPERATIVE
APPLICABLE MODEL(S)/VINS
2006 Mazda6 and Mazdaspeed6
2007 CX-7
DESCRIPTION
The 2006 Mazda6/Mazdaspeed6 and 2007 CX-7 vehicles are equipped with "Auto Open/Close" and "Anti-Pinch" window features.
This system requires a special "Power Window Initialization Procedure" for these features to operate~ The power window initialization procedure is performed during vehicle production, however, in the following cases the initialization procedure must be performed in order to restore "auto open/close" and "anti-pinch" operation.
^ Battery has been disconnected.
^ Power window fuse has been removed/replaced.
^ Power window initialization procedure was not performed at vehicle production.
NOTE:
TO AVOID UNNECESSARY REPLACEMENT OF THE POWER WINDOW MAIN SWITCH, ALWAYS PERFORM THE "POWER WINDOW INITIALIZATION PROCEDURE" BEFORE REPLACING ANY POWER WINDOW RELATED PARTS.
POWER WINDOW INITIALIZATION PROCEDURE
1. Turn ignition to ON position.
2. From driver's seat ensure window lockout switch is NOT depressed.
3. Press window switch down to fully open door window.
4. Pull window switch up to fully close door window; hold switch up for two (2) seconds; release switch.
5. Move to front passenger seat and repeat Steps 3 - 4 on passenger window switch.
6. Mazdaspeed6 Only: Move to rear seat and repeat Steps 3 - 4 at left and right rear seat window switches.
7. Verify proper window operation using each door switch.
Disclaimer
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
