Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2007 Mazda 6 L4-2.3LFACTORY OEM SERVICE PROCEDURE
Keyless Entry - Security Access Procedure: Overview
TSB: 09-003/06
MULTI-MODEL - SECURITY ACCESS PROCEDURE CHANGE FOR CODED ACCESS PATS AND ADVANCED KEYLESS SYSTEM - SERVICE TIP
BULLETIN NOTE
This bulletin supersedes the previous bulletin issued on 01/26/06. The APPLICABLE MODELS and DESCRIPTION have been revised.
APPLICABLE MODEL(S)/VINS
2003-2007 Mazda6
2004-2007 Mazda3
2004-2007 RX-8
2006-2007 Mazda5
2006-2007 Mazdaspeed6
2006-2007 MX-5
2007 CX-7
DESCRIPTION
The MS3 Incode website will require VIN, Part Number, Serial Number and Error Control in addition to the Outcode in order to obtain the appropriate Incode for the subject models. The Incode is then used to grant access to the PATS security. This change has been implemented to enhance the overall security when gaining access to the system.

The IDS/PDS will provide the following for each module affected in PATS security access.
^ Dealer Code
^ Technician Name
^ Technician ID (last 4 digits of SSN)
^ E-mail
^ VIN
^ Part Number
^ Serial Number
^ Error Control Number
^ Request Reason
^ Model Type
^ Outcode
Mazda Incode web site has been updated to reflect PATS application software of IDS/PDS. Please pay close attention to the following for accessing PATS INCODES on Mazda Service Support System (MS3).
^ You MUST be an authorized Mazda Technician, Senior Technician, Master Technician, Shop Foreman, Service Manager or Service Director. Technician Trainees are not allowed access to the incode information.
^ Security for access to the INCODE information has been changed. If you are not the technician that initiated the existing MS3 session, and you fit any of the criteria listed above, you must log out of MS3 and re-initiate a new MS3 session using your user ID and password.
^ Please follow the repair procedure to obtain Incode.

Disclaimer
MULTI-MODEL - SECURITY ACCESS PROCEDURE CHANGE FOR CODED ACCESS PATS AND ADVANCED KEYLESS SYSTEM - SERVICE TIP
BULLETIN NOTE
This bulletin supersedes the previous bulletin issued on 01/26/06. The APPLICABLE MODELS and DESCRIPTION have been revised.
APPLICABLE MODEL(S)/VINS
2003-2007 Mazda6
2004-2007 Mazda3
2004-2007 RX-8
2006-2007 Mazda5
2006-2007 Mazdaspeed6
2006-2007 MX-5
2007 CX-7
DESCRIPTION
The MS3 Incode website will require VIN, Part Number, Serial Number and Error Control in addition to the Outcode in order to obtain the appropriate Incode for the subject models. The Incode is then used to grant access to the PATS security. This change has been implemented to enhance the overall security when gaining access to the system.
The IDS/PDS will provide the following for each module affected in PATS security access.
^ Dealer Code
^ Technician Name
^ Technician ID (last 4 digits of SSN)
^ VIN
^ Part Number
^ Serial Number
^ Error Control Number
^ Request Reason
^ Model Type
^ Outcode
Mazda Incode web site has been updated to reflect PATS application software of IDS/PDS. Please pay close attention to the following for accessing PATS INCODES on Mazda Service Support System (MS3).
^ You MUST be an authorized Mazda Technician, Senior Technician, Master Technician, Shop Foreman, Service Manager or Service Director. Technician Trainees are not allowed access to the incode information.
^ Security for access to the INCODE information has been changed. If you are not the technician that initiated the existing MS3 session, and you fit any of the criteria listed above, you must log out of MS3 and re-initiate a new MS3 session using your user ID and password.
^ Please follow the repair procedure to obtain Incode.
Disclaimer
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
