Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2007 Mazda 5 L4-2.3LFACTORY OEM SERVICE PROCEDURE
Powertrain Management: Technical Service Bulletins
- Customer Interest
- Emissions - MIL ON/DTC's P2401/P2402/P2404 Stored
- Engine/Fuel - MIL ON/DTC P2006 Stored
- Emissions - MIL ON/DTC's P0441/P0442/P0455/P0456 Set
- Fuel System - MIL ON/DTC's P0442/P0455/P0456
- Engine Controls - MIL ON/DTC's P0131/P2251
- Emissions - MIL ON/DTC P0441 Set
- Engine Controls - Intermittent Engine Stumble
- Engine Controls - Engine Stalls Driving at Low Speeds
- Engine Controls - MIL ON/DTC P0128 Stored
- AT, Engine Controls - ECM/TCM Update
- Ignition System - Idle Fluctuation/Engine Vibration
- Engine Controls - Engine Stalling at Low Speeds
- Engine - Unstable Idle/Engine Stalling
- Engine - VVT Noise At Engine Start Up
- By Symptom
- Abnormal wear/deterioration
- Customer Interest
- Emissions - MIL ON/DTC's P2401/P2402/P2404 Stored
- Engine/Fuel - MIL ON/DTC P2006 Stored
- Emissions - MIL ON/DTC's P0441/P0442/P0455/P0456 Set
- Fuel System - MIL ON/DTC's P0442/P0455/P0456
- Engine Controls - MIL ON/DTC's P0131/P2251
- Emissions - MIL ON/DTC P0441 Set
- Engine Controls - Intermittent Engine Stumble
- Engine Controls - Engine Stalls Driving at Low Speeds
- Engine Controls - MIL ON/DTC P0128 Stored
- AT, Engine Controls - ECM/TCM Update
- Ignition System - Idle Fluctuation/Engine Vibration
- Engine Controls - Engine Stalling at Low Speeds
- Engine - Unstable Idle/Engine Stalling
- Engine - VVT Noise At Engine Start Up
- Driveability
- False instrument warning light/gauges
- Noise
- Odors
- Sticking/Binding
- Vibration
- All Technical Service Bulletins
- Exhaust System - Excessive Sulfur Odors
- Emissions - MIL ON/DTC's P2401/P2402/P2404 Stored
- Fuel System - Fuel Ethanol Content Testing
- Computers/Controls KAM Memory Clearing After VVT R & R
- Fuel System - Ethanol Fuel Usage
- Electrical - Lightning Strike Information
- Engine/Fuel - MIL ON/DTC P2006 Stored
- Engine Controls - O2 Sensor Removal Precautions
- Emissions - MIL ON/DTC's P0441/P0442/P0455/P0456 Set
- Fuel System - MIL ON/DTC's P0442/P0455/P0456
- Engine Controls - MIL ON/DTC's P0131/P2251
- Emissions - MIL ON/DTC P0441 Set
- Computers/Controls - Module Reprogramming Precautions
- Engine Controls - Intermittent Engine Stumble
- Engine Controls - Engine Stalls Driving at Low Speeds
- Engine Controls - MIL ON/DTC P0128 Stored
- Ignition System - Spark Plug Removal/Installation
- AT, Engine Controls - ECM/TCM Update
- Ignition System - Idle Fluctuation/Engine Vibration
- Engine Controls - Engine Stalling at Low Speeds
- A/T - Range Switch Removal/Installation Caution
- Engine - Unstable Idle/Engine Stalling
- Engine - VVT Noise At Engine Start Up
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.