Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2007 Mazda 3 L4-2.3LFACTORY OEM SERVICE PROCEDURE
Instruments - Configuring Odometer Data: Overview
Bulletin No.: 09-025/08
Last Issued: 8/29/2008
Subject:
ODOMETER DATA CONFIGURATION
BULLETIN NOTE:
This bulletin supersedes the previous bulletin 09-034/06, issued on 07/26/2006 and 09-009/07, issued on 03/14/2007. The APPLICABLE MODEL(S)/VINS and REPAIR PROCEDURE have been revised.
APPLICABLE MODEL(S)/VINS
2007-2009 CX-7
2007-2009 CX-9
2007-2009 Mazda3
2007-2009 MAZDASPEED3
2006-2009 Mazda5
2006-2009 MX-5
2009 Mazda6
DESCRIPTION
In the event the instrument cluster is replaced, this service tip provides information on copying odometer data from the old odometer to a new one using IDS/PDS updated to the latest software level. Data can be recorded to a new odometer unit, if the following conditions are met:
- Data in the old unit can be retrieved by IDS/PDS
- Odometer in the new instrument cluster is less than 63 mi (100 km)
- New instrument cluster has no damage (ie: "---" is not displayed)
- Instrument cluster voltage is over 9 volts.
NOTE:
^ A new or used instrument cluster with more that 63 mi (100 km) cannot be programmed with a different mileage.
^ There are two procedures in the bulletin, one for vehicles equipped without Advanced Keyless system and one for vehicles with Advanced Keyless system.

Disclaimer
Last Issued: 8/29/2008
Subject:
ODOMETER DATA CONFIGURATION
BULLETIN NOTE:
This bulletin supersedes the previous bulletin 09-034/06, issued on 07/26/2006 and 09-009/07, issued on 03/14/2007. The APPLICABLE MODEL(S)/VINS and REPAIR PROCEDURE have been revised.
APPLICABLE MODEL(S)/VINS
2007-2009 CX-7
2007-2009 CX-9
2007-2009 Mazda3
2007-2009 MAZDASPEED3
2006-2009 Mazda5
2006-2009 MX-5
2009 Mazda6
DESCRIPTION
In the event the instrument cluster is replaced, this service tip provides information on copying odometer data from the old odometer to a new one using IDS/PDS updated to the latest software level. Data can be recorded to a new odometer unit, if the following conditions are met:
- Data in the old unit can be retrieved by IDS/PDS
- Odometer in the new instrument cluster is less than 63 mi (100 km)
- New instrument cluster has no damage (ie: "---" is not displayed)
- Instrument cluster voltage is over 9 volts.
NOTE:
^ A new or used instrument cluster with more that 63 mi (100 km) cannot be programmed with a different mileage.
^ There are two procedures in the bulletin, one for vehicles equipped without Advanced Keyless system and one for vehicles with Advanced Keyless system.
Disclaimer
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
