Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2007 Mazda 3 L4-2.3LFACTORY OEM SERVICE PROCEDURE
Powertrain Management: Technical Service Bulletins
- Recalls
- Customer Interest
- Engine Controls/Cooling System - MIL ON/DTC P0128 Set
- Engine/Fuel - MIL ON/DTC P2006 Stored
- Emissions - MIL ON/DTC's P0441/P0442/P0455/P0456 Set
- Fuel System - MIL ON/DTC's P0442/P0455/P0456
- Engine Controls - MIL ON/DTC's P0131/P2251
- Emissions - MIL ON/DTC P2404 Set
- Engine - MIL ON/DTC P2004 Set
- Emissions - MIL ON/DTC P0441 Set
- Engine Controls - MIL ON/DTC P0401 Set
- Engine Controls - Idle Dip When A/C Cycles ON
- Engine - MIL ON/DTC P2006 Set
- Engine Control - Engine Stall/Hesitation After Hot Start
- AT, Engine Controls - ECM/TCM Update
- Engine - Unstable Idle/Engine Stalling
- Engine - VVT Noise At Engine Start Up
- By Symptom
- Abnormal wear/deterioration
- Customer Interest
- Engine Controls/Cooling System - MIL ON/DTC P0128 Set
- Engine/Fuel - MIL ON/DTC P2006 Stored
- Emissions - MIL ON/DTC's P0441/P0442/P0455/P0456 Set
- Fuel System - MIL ON/DTC's P0442/P0455/P0456
- Engine Controls - MIL ON/DTC's P0131/P2251
- Emissions - MIL ON/DTC P2404 Set
- Engine - MIL ON/DTC P2004 Set
- Emissions - MIL ON/DTC P0441 Set
- Engine Controls - MIL ON/DTC P0401 Set
- Engine Controls - Idle Dip When A/C Cycles ON
- Engine - MIL ON/DTC P2006 Set
- Engine Control - Engine Stall/Hesitation After Hot Start
- AT, Engine Controls - ECM/TCM Update
- Engine - Unstable Idle/Engine Stalling
- Engine - VVT Noise At Engine Start Up
- Driveability
- Noise
- Odors
- Recalls
- Sticking/Binding
- All Technical Service Bulletins
- Exhaust System - Excessive Sulfur Odors
- Fuel System - Fuel Ethanol Content Testing
- Computers/Controls KAM Memory Clearing After VVT R & R
- Fuel System - Ethanol Fuel Usage
- Electrical - Lightning Strike Information
- Engine Controls/Cooling System - MIL ON/DTC P0128 Set
- Engine/Fuel - MIL ON/DTC P2006 Stored
- Engine Controls - O2 Sensor Removal Precautions
- Emissions - MIL ON/DTC's P0441/P0442/P0455/P0456 Set
- Fuel System - MIL ON/DTC's P0442/P0455/P0456
- Engine Controls - MIL ON/DTC's P0131/P2251
- Emissions - MIL ON/DTC P2404 Set
- Engine - MIL ON/DTC P2004 Set
- Emissions - MIL ON/DTC P0441 Set
- Computers/Controls - Module Reprogramming Precautions
- Engine Controls - Revised DTC P0441 Diagnostics
- Engine Controls - MIL ON/DTC P0401 Set
- Engine Controls - Idle Dip When A/C Cycles ON
- Engine - MIL ON/DTC P2006 Set
- Engine Control - Engine Stall/Hesitation After Hot Start
- Ignition System - Spark Plug Removal/Installation
- AT, Engine Controls - ECM/TCM Update
- Recall 07V052000: Floor Mat/Accelerator Interference
- A/T - Range Switch Removal/Installation Caution
- Fuel System - Servicing Precautions
- Engine - Unstable Idle/Engine Stalling
- A/T - Speed Sensor Replacement
- Engine - VVT Noise At Engine Start Up
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.