2006 Mazda MX-5 Miata BaseFACTORY OEM SERVICE PROCEDURE

Immobilizer System Component Replacement/Key Addition And Clearing [With Advanced Keyless System]: Foreword

  • When performing the following procedures, the immobilizer resetting procedure using the WDS or equivalent must also always be performed: "Keyless control module replacement", "PCM replacement", "Steering lock unit replacement", "Keyless control module and PCM joint replacement", "Keyless control module, PCM, and steering lock unit joint replacement", and "Key ID number clearing". The engine will not start unless all work is performed using the WDS or equivalent.
  • A card key that can start the engine is necessary for the key programming. If there is no card key that can start the engine, perform the key programming after the card key programming. (See CARD KEY ID CODE REGISTRATION [WITH ADVANCED KEYLESS SYSTEM]  .)
  • There are two ways to add supplemental key: Using the WDS or equivalent or using two keys that can start the engine to program.
  • When replacing any of the immobilizer system component parts, adding/clearing keys, or performing other functions, refer to IMMOBILIZER SYSTEM FUNCTION TABLE  and perform the applicable procedure (No.1 to 5).
  • Verify that the room fuse is equipped.
IMMOBILIZER SYSTEM FUNCTION TABLE

Ref. No. Condition Items necessary for procedure (prepare before starting procedure) Cautionary notes
1 Since two or more keys that can start the engine are necessary, make a spare key. Or program an additional key.
  • Programming key
  • The WDS or equivalent is necessary for the additional key programming if "Customer spare key programming disable" is performed before the procedure using the WDS or equivalent. In this case, perform No. 2.
2 If there is only one key that can start the engine, make a spare key. If there is no key, program an additional key.
  • Programmed card key
  • Programming key
  • WDS or equivalent
-
3 Replacing the PCM only.
  • New PCM
  • Programmed card key
  • Programming keys (two or more)
  • WDS or equivalent
-
4 Changing the additional key programming procedure. (Method for programming other keys using two keys that can start the engine is disabled.)
  • WDS or equivalent
  • The additional key programming using No. 1 cannot be performed after the procedure. It is possible to restore the setting. For restoring the setting, the WDS or equivalent is necessary.
4 Changing the additional key programming procedure. Allows programming using two keys that can start the engine.
  • WDS or equivalent
  • New vehicles have this setting.
3 Clearing the programmed key ID number.
  • Programming keys (two or more)
  • WDS or equivalent
3 Replacing all the keys. (Steering lock unit is not replaced)
  • Programmed card key
  • Programming keys (two or more)
  • WDS or equivalent
5 Replacing the steering lock unit.
  • New steering lock unit
  • Programmed card key
  • New keys (two or more)
  • WDS or equivalent
5 Replacing the keyless control module.
  • New keyless control module
  • Card key
  • Programming keys (two or more)
  • WDS or equivalent
5 Replacing the instrument cluster.
  • New instrument cluster
  • Card key
  • Programming keys (two or more)
  • WDS or equivalent
- Replacing the coil antenna.
  • New coil antenna
  • Immobilizer system resetting is not necessary.
CAUTION:
  • The following conditions may cause poor signal communication between the key and vehicle, resulting in the engine not starting or a key registration error. Do not perform any work under the following conditions:
    • Placing the following items close to the key grip or contacting it.
      • Spare keys
      • Keys for other vehicles equipped with an immobilizer system
      • Any metallic object
      • Any electronic device, or any credit or other card with magnetic strips
  • Do not place the following devices in the vehicle while programming, otherwise programming cannot be performed:
    • WDS or equivalent
    • Personal computer
    • Devices that can send/receive the radio waves
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.