2005 Mazda 6 s, 4D Hatchback, AutomaticFACTORY OEM SERVICE PROCEDURE

PID/DATA MONITOR table (Reference)

PID/DATA MONITOR

Monitor item (Definition) Unit/Condition Condition/Specification (Reference) Inspection item (s) PCM terminal
AAT (Ambient air temperature) °C or °F Ignition switch at ON position: Indicate the ambient air temperature -
AC REQ (A/C switch) On/Off A/C switch and fan switch ON at ignition switch ON: On
A/C switch OFF at ignition switch ON: Off
5
ACCS (A/C relay) On/Off A/C is operating: On
Ignition switch is ON: Off
47
ALTF (Generator field coil control duty value) % Ignition switch is ON: 0%
Idling, E/L is operating: Duty value rises
  • Inspect following PIDs: ALTT V, ECT, IAT, RPM, VBAT
36
ALTT V (Generator output voltage) V Ignition switch is ON: 0 V
Idling: 14-16 V
63
APP (Accelerator pedal position) % CTP: Approx. 0%
WOT: Approx. 99.2%
42,43
APP1 (APP sensor No. 1) % AP is released: 31.0-32.4%
AP is depressed: 69.8-81.8%
43
V AP is released: 1.55-1.62 V
AP is depressed: 3.49-4.09 V
APP2 (APP sensor No. 2) % AP is released: 20.2-21.4%
AP is depressed: 58.8-70.8%
42
V AP is released: 1.01-1.07 V
AP is depressed: 2.94-3.54 V
ARPMDES (Target engine speed) RPM Idling (no load): 700-800 RPM -
B+ (Battery positive voltage) V Ignition switch is ON: B+ 86
BARO (Barometric pressure) kPa, Bar, psi Ignition switch is ON at sea level: Approx. 101 kPa {1.01 Bar, 14.6 psi} 37
BARO/EGR (EGR boost sensor solenoid valve) On/Off Ignition switch is ON: Off Idling: Off 93
BOO (Brake switch No. 1) On/Off Brake pedal is depressed: On
Brake pedal is released: Off
82
BPA (Brake switch No. 2) On/Off Brake pedal is depressed: Off
Brake pedal is released: On
56
CATT11_DSD (Estimated catalytic converter temperature) °C or °F Idling after warm-up: Approx. 450 °C {840 °F} -
CATT21_DSD (Estimated catalytic converter temperature) °C or °F Idling after warm-up: Approx. 450 °C {840 °F) -
CHRGLP (Generator warning light) On/Off Ignition switch is ON: On
Idling: Off
-
COLP (Refrigerant pressure switch (middle)) On/Off Idling, refrigerant pressure switch (middle) is on: On
Idling, refrigerant pressure switch (middle) is off: Off
30
CPP(1) (Clutch pedal position) On/Off Clutch pedal is depressed: On
Clutch pedal is released: Off
29
CPP/PNP(1) (Shift lever position) Neutral/Drive Gear is neutral position: Neutral
Gear is not neutral position: Drive
31
DTCCNT (Number of DTC detected) - - -
ECT (Engine coolant temperature) °C or °F ECT is 20 °C {68 °F}: 20 °C {68 °F}
ECT is 60 °C {140 °F}: 60 °C {140 °F}
41
V ECT is 20 °C {68 °F}: 2.9-3.1 V After warm-up: 0.2-1.0 V
EQ_RAT11_DSD (Front oxygen sensor) - Idling after warm-up: Approx. 1
  • Perform applicable DTC troubleshooting.

    (See DTC TABLE )

-
ETC_ACT (Electronic throttle control actual) ° Accelerator pedal is released: Approx. 7.4°
Accelerator pedal is released: Approx. 74.3°
39,40
ETC_DSD (Electronic throttle control desired) % Throttle valve is closed --> open: PID value changes smoothly 39,40
° Accelerator pedal is released: Approx. 0°
Accelerator pedal is released: Approx. 74°
EVAPCP (Purge solenoid valve duty value) % Ignition switch is ON: 0%
  • Inspect following PIDs: BARO, ECT, IAT, MAF, O2S11, O2S21, RPM, TP REL, VBAT
85
FAN_DUTY (Fan control signal) % ECT is below 100 °C {212 °F}: 0%
ECT is above 100 °C {212 °F}: 50-100%
  • Inspect following PIDs: ACSW, COLP, ECT, VBAT
69
FLI (Fuel level) % - - -
FP (Fuel pump relay) On/Off Ignition switch is ON: Off
Idling: On
Cranking: On
95
FUELPW (Fuel injection duration) ms Ignition switch is ON: 0 ms
Idling: 1.5-3.0 ms
  • Inspect following PIDs: ACSW, ALTT V, ECT, IAT, INGEAR, MAF, MAP, O2S11, O2S12, O2S21, O2S22, PSP, RPM, TP REL, VBAT
  • Fuel injector

    (See FUEL INJECTOR INSPECTION [AJ] .)

48, 49, 50, 74, 75, 76
FUEL SYS1 (Fuel system status) OL/CL/OL Drive/OL Fault/CL Fault Ignition switch is ON: CL
Idling after warm-up: CL
  • Inspect following PIDs: ACSW, ALTT V, ECT, IAT, INGEAR, MAF, MAP, O2S11, O2S12, O2S21, O2S22, PSP, RPM, TP REL, VBAT
  • Fuel injector

    (See FUEL INJECTOR INSPECTION [AJ] .)

-
FUEL SYS2 (Fuel system status) OL/CL/OL Drive/OL Fault/CL Fault Ignition switch is ON: CL
Idling after warm-up: CL
  • Inspect following PIDs: ACSW, ALTT V, ECT, IAT, INGEAR, MAF, MAP, O2S11, O2S12, O2S21, O2S22, PSP, RPM, TP REL, VBAT
  • Fuel injector

    (See FUEL INJECTOR INSPECTION [AJ] .)

-
GENVDSD (Generator voltage desired) V Ignition switch is ON: 0 V
Idling, E/L is not operating: Approx. 14.9 V
-
HTR11 (HO2S heater (RF)) On/Off Idle after warm-up: On and Off
  • Inspect following PIDs: ECT, MAF, RPM, TP REL
83
HTR12 (HO2S heater (RR)) On/Off Idling: On
Engine speed is above 4,000 rpm: Off
  • Inspect following PIDs: ECT, MAF, RPM, TP REL
57
HTR21 (HO2S heater (LF)) On/Off Idle after warm-up: On and Off
  • Inspect following PIDs: ECT, MAF, RPM, TP REL
84
HTR22 (HO2S heater (LR)) On/Off Idling: On
Engine speed is above 4,000 rpm: Off
  • Inspect following PIDs: ECT, MAF, RPM, TP REL
58
IASV (VAD control solenoid valve) On/Off TP opening angle is less than 60% and engine speed is 6,000 rpm or above: On
TP opening angle is 60% or above and engine speed is 4,800 rpm or above: On Others: Off
  • Inspect following PIDs: ECT, RPM, TP REL
68
IAT (Intake air temperature) °C or °F IAT is 20 °C {68 °F}: 20 °C {68 °F}
IAT is 30 °C {86 °F}: 30 °C {86 °F}
15
V IAT is 20 °C {68 °F}: 2.4-2.6 V
IAT is 30 °C {86 °F}: 1.7-1.9 V
INGEAR (Load/no load condition) On/Off Gear is not neutral position and clutch pedal is released: On
Gear is neutral position: Off
Clutch pedal is depressed: Off
  • Inspect following PIDs: CPP, CPP/PNP
  • DTC inspection

    (See DTC TABLE .)

29, 31(1) __(2)
IVS (CTP condition) Idle/Off Idle CTP: Idle
Others: Off Idle
39,40
KNOCKR (Knocking retard) ° Ignition switch is ON: 0 ° Idling: 0 ° 3,81
LDP EVAPCP (EVAP system leak detection pump detect incorrect purge flow) mA Indicate the EVAP control system incorrect purge flow detection value Perform applicable DTC troubleshooting.
(See DTC TABLE )
-
LDP IDL (EVAP system leak detection pump idle current) mA Indicate the EVAP system leak detection pump idle current
  • Perform applicable DTC troubleshooting.

    (See DTC TABLE )

-
LDP MON (EVAP system leak detection pump monitoring current) mA Indicate the EVAP system leak detection pump monitoring current
  • Perform applicable DTC troubleshooting.

    (See DTC TABLE )

-
LDP REF (EVAP system leak detection pump reference current) mA Indicate the EVAP system leak detection pump reference current
  • Perform applicable DTC troubleshooting.

    (See DTC TABLE )

-
LDP SLDV (EVAP system small leak detection value) mA Indicate the EVAP control system small leak detection value
  • Perform applicable DTC troubleshooting.

    (See DTC TABLE )

-
LDP VSLDV(3) (EVAP system small leak detection value) mA or ms Indicate the EVAP control system vary small leak detection value
  • Perform applicable DTC troubleshooting.

    (See DTC TABLE )

-
LOAD (Engine load) % MTX 
Idling: Approx. 16.8%
Engine speed is 2,500 rpm: Approx. 14.6%
ATX 
Idling: Approx. 17.5%
Engine speed is 2,500 rpm: Approx. 15.2%
  • Inspect following PIDs: ECT, IAT, MAF, MAP, RPM, TP REL
-
LONGFT1 (Long term fuel trim (RH)) % Idling: -20-20% -
LONGFT2 (Long term fuel trim (LH)) % Idling: -20-20% -
MAF (Mass airflow) g/s MTX 
Idling: 3.6-3.8 g/s
Engine speed is 2,500 rpm: 10.5-11.2 g/s
ATX 
Idling: 3.8-4.0 g/s
Engine speed is 2,500 rpm: 10.6-11.4 g/s
11
V Idling: Approx. 1.3 V
Engine speed is 2,500 rpm: Approx. 1.9 V
MIL (Malfunction indicator light) On/Off Ignition switch is ON: On
Idling: Off
-
MIL_DIS (Travelled distance since the MIL illuminated) km or mile No DTC: 0 km {0 mile}
DTC detected: Not 0 km {0 mile}
-
NUMKEYS (Number of keys stored in module) - Indicate the number of keys stored in module - -
O2S11 (HO2S (RF)) V Ignition switch is ON: 0-1.0 V
Idling after warm-up: 0-1.0 V
Acceleration: 0.5-1.0 V
Deceleration: 0-0.5 V
18
O2S12 (HO2S (RR)) V Idling after warm-up: Approx. 0.6 V 44
O2S21 (HO2S (LF)) V Ignition switch is ON: 0-1.0 V
Idling after warm-up: 0-1.0 V
Acceleration: 0.5-1.0 V
Deceleration: 0-0.5 V
19
O2S22 (HO2S (LR)) V Idling after warm-up: Approx. 0.6 V 45
PSP (PSP switch) High/Low Steering wheel is in straight ahead position: Low
Steering wheel is turned: High
55
RFCFLAG (Readiness Function Code) Learned/Not Learned RFC exists: Learned
No RFC: Not Learned
-
RO2FT1 (HO2S (RR) fuel trim) - Idling after warm-up: Approx. - 0.03-0.03 -
RO2FT2 (HO2S (RL) fuel trim) - Idling after warm-up: Approx. - 0.03-0.03 -
RPM (Engine speed) RPM Idling (no load): 700-800 RPM 1,27
SCCS (Cruise control switch) V Press ON/OFF: Approx. 0 V
Press CALCEL: Approx. 1.2 V
Press SET/COAST: Approx. 3.2 V
Press RES/ACCEL: Approx. 4.2 V
Others: Approx. 5.0 V
12
SEGRP (EGR valve position) No. of step Ignition switch is ON: 0 step
Idling: 0 step
Cranking: 0-60 steps
-
SEGRP DSD (Desired EGR valve position) % Ignition switch is ON: 0%
Idling: 0%
Cranking: 0-100%
  • Inspect following PIDs: ECT, IAT, MAF, RPM, VSS
-
SELTESTDTC (KOEO/KOER DTC) - - -
SHRTFT1 (Short term fuel trim (RH)) % Idling: -20-20% -
SHRTFT11 (Short term fuel trim (RF)) % Idling: -20-20% -
SHRTFT12 (Short term fuel trim (LF)) % Idling: -20-20% -
SHRTFT2 (Short term fuel trim (LH)) % Idling: -20-20% -
SHRTFT21 (Short term fuel trim (RR)) % Idling: -20-20% -
SHRTFT22 (Short term fuel trim (LR)) % Idling: -20-20% -
SPARKADV (Ignition timing) ° (BTDC) Ignition switch is ON: 0° (BTDC)
Idling: Approx. 10° (BTDC)
  • Inspect following PIDs: ACSW, ALTT V, CPP, CPP/PNP, ECT, KNOCKR, MAF, PSP, RPM, TP REL, VSS
  • Perform engine tune-up

    (See ENGINE TUNE-UP .)

-
test (Test mode) On/Off - - -
TIRESIZE (Tire revolution per mile) rev/mile 808 is displayed - -
TP REL (Relative throttle position) % Throttle valve is closed --> open: PID value changes smoothly 39,40
TP1 (TP sensor No. 1 signal voltage) % Ignition switch is ON and accelerator pedal not depressed: 13-24%
Ignition switch is ON and WOT: Approx. 78%
40
V Ignition switch is ON and accelerator pedal not depressed: 3.8-4.35 V
Ignition switch is ON and WOT: Approx. 1.1 V
TP2 (TP sensor No. 2 signal voltage) % Ignition switch is ON and accelerator pedal not depressed: 15-36%
Ignition switch is ON and WOT: Approx. 88%
39
V Ignition switch is ON and accelerator pedal not depressed: 0.75-1.8 V
Ignition switch is ON and WOT: Approx. 4.4 V
TPCT (Relative throttle position) V Ignition switch is ON: 0 V 39,40
VSS (Vehicle speed) KPH or MPH Vehicle speed is 20 km/h {12 mph}: 20 KPH {12 MPH}
Vehicle speed is 40 km/h {25 mph}: 40 KPH {25 MPH}
-
VT ACT1 (Actual valve timing (RH)) ° Idling: 0° 2,28
VT ACT2 (Actual valve timing (LH)) ° Idling: 0° 54, 80
VT DIFF1 (Difference between actual and target valve timing (RH)) ° Idling: 0° 2,28
VT DIFF2 (Difference between actual and target valve timing (LH)) ° Idling: 0° 54, 80
VT DUTY1 (OCV control signal (RH)) % Idling: 0% 2,28
VT DUTY2 (OCV control signal (LH)) % Idling: 0% 54,80
(1) MTX
(2) ATX
(3) California emission regulation applicable model
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.