Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
1995 Mazda Millenia BaseFACTORY OEM SERVICE PROCEDURE
Automatic Transmissions DTCS
AUTOMATIC TRANSMISSIONS DTCS
| DTC | Description |
|---|---|
| P0705 | TRANSAXLE RANGE SWITCH CIRCUIT MALFUNCTION |
| P0710 | TRANSAXLE FLUID TEMPERATURE (TFT) SENSOR CIRCUIT MALFUNCTION |
| P0720 | OUTPUT SPEED SENSOR |
| P0725 | ENGINE SPEED INPUT CIRCUIT MALFUNCTION |
| P0731 | INCORRECT 1ST GEAR RATIO |
| P0732 | INCORRECT 2ND GEAR RATIO |
| P0733 | INCORRECT 3RD GEAR RATIO |
| P0734 | INCORRECT 4TH GEAR RATIO |
| P0740 | TORQUE CONVERTER CLUTCH MALFUNCTION |
| P0745 | PRESSURE CONTROL SOLENOID MALFUNCTION |
| P0750 | SHIFT SOLENOID "A" MALFUNCTION |
| P0755 | SHIFT SOLENOID "B" MALFUNCTION |
| P1720 | VEHICLE SPEED SENSOR (VSS) # 2 MALFUNCTION |
| P1743 | LOCK-UP SOLENOID MALFUNCTION |
| P1770 | OVERRUNNING CLUTCH SOLENOID VALVE MALFUNCTION |
| P1790 | THROTTLE POSITION (TP) SENSOR MALFUNCTION |
AUTOMATIC TRANSMISSIONS DTCS (1995-96 MILLENIA, PROTEGE & 1996 MX-6, 626)
| DTC | Description | ||||
|---|---|---|---|---|---|
| P0705 | Transaxle Range Switch | ||||
| P0710 | (1) TFT Sensor | ||||
| P0715 | Turbine Speed Sensor | ||||
| P0725 | Engine Speed Input Circuit Malfunction | ||||
| P0730 | (2) Incorrect Gear Ratio | ||||
| P0731 | Incorrect 1st Gear Ratio | ||||
| P0732 | Incorrect 2nd Gear Ratio | ||||
| P0733 | Incorrect 3rd Gear Ratio | ||||
| P0734 | Incorrect 4th Gear Ratio | ||||
| P0740 | TCC System Malfunction | ||||
| P0745 | Pressure Control Solenoid | ||||
| P0750 | Shift Solenoid "A" | ||||
| P0755 | Shift Solenoid "B" | ||||
| P0760 | Shift Solenoid "C" | ||||
| P1720 | (2) Speedometer Sensor | ||||
| P1743 | TCC Control Solenoid Valve | ||||
| P1744 | TCC Solenoid Valve | ||||
| P1765 | 3-2 Timing Solenoid Valve | ||||
| P1775 | (2) Reduce Torque Signal No. 1 | ||||
| P1776 | (2) Reduce Torque Signal No. 2 | ||||
| P1777 | (2) Torque Reduced/Coolant Temp Signal | ||||
| P1790 | (2) Throttle Position Sensor | ||||
| P1792 | (2) Closed Throttle Position Switch | ||||
| P1795 | (2) EGR Boost Sensor | ||||
|
|||||
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.