1994 Mazda 929FACTORY OEM SERVICE PROCEDURE

Section 7 (Engine Controls - Specifications): Capacities

WARNING: This page is about a different car, the 1994 Mazda Navajo and 1994 Mazda B4000. However, it is still accessible from the selected car via links, so may be relevant.
BATTERY SPECIFICATIONS

Application Amp Hr. Rating
B4000
Standard 60
Heavy-Duty 80
Navajo 72
FLUID CAPACITIES

Application Quantity
Crankcase (Includes Filter)
B4000 5.0 Qts. (4.7L)
Navajo 5.0 Qts. (4.7L)
Cooling System (Includes Heater)
B4000
Light-Duty 8.1 Qts. (7.6L)
Heavy-Duty 8.5 Qts. (8.0L)
Navajo
With A/T 8.5 Qts. (8.0L)
Without A/T 8.1 Qts. (7.6L)
Manual Transmission (1)
B4000 5-Spd. 2.9 Qts. (2.7L)
Navajo 2.8 Qts. (2.6L)
Automatic Transmission (ATF M-III or Dexron-II)
B4000 (4x2) 9.7 Qts. (9.2L)
B4000 (4x4) 10.0 Qts. (9.5L)
Navajo 3.0 Qts. (2.8L)
4x2 9.7 Qts. (9.2L)
4x4 10.0 Qts. (9.5L)
Front Differential (2)
B4000
Dana 28 1.5 Qts. (1.4L)
Dana 35 1.8 Qts. (1.7L)
Navajo 1.7 Qts. (1.6L)
Rear Differential (2)
B4000
Standard 2.5 Qts. (2.4L)
Limited Slip (3) 2.6 Qts. (2.5L)
Navajo 2.6 Qts. (2.5L)
Transfer Case (4)
B4000 1.3 Qts. (1.2L)
Navajo (5) 1.3 Qts. (1.2L)
(1) On B4000, use ATF Dexron II. On Navajo, use Mercon ATF.
(2) On Navajo, use SAE 90. On B4000, use SAE 90 for temperatures greater than 0°F (-18°C), and SAE 80W for temperatures less than 0°F (-18°C).
(3) With 4oz. of appropriate friction modifier added.
(4) On Navajo, use Mercon ATF. On B4000, use SAE 75W-90 or ATF Dexron-II for all-season conditions, and SAE 80W-90 or SAE 90 for temperatures greater than 0°F (-18°C).
(5) For all-season conditions, use SAE 75W-90. If temperature is less than 0°F (-18°C), use ATF Dexron-II.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.