WARNING: This page is about a different car, the 2019 Lincoln MKC. However, it is still accessible from the selected car via links, so may be relevant.

The chart describes specific module configuration information:

Module Name	Module Address	Programmable Module Installation (PMI) Available	Reprogram/Flash Capable	Requires Adaptive Learning or Calibration	Available Programmable Parameters
APIM	7D0	Yes	Yes	No	Travel Link
ABS module	760	Yes	Yes	IVD initialization EPB apply and release	None
ACM	727	Yes	Yes	No	SDARS Data Services
BCM	726	Yes	Yes	Ambient lighting calibration Rear view camera calibration	Autolamp delay Auto lock/unlock Auto relock DRL configuration (except Canada, China and Premier trim option [all other markets]) DRL by Autolamps DRL include parklamps DRL conditions Global open/close Mislock horn One/two stage unlock Park lock control Passive entry/passive start enable/disable Remote start enable/disable Remote start duration setting Trim switch inhibit enable/disable Door key enable/disable Trailer outage Rain sensing enable Front/rear courtesy wipe Rear/reverse wipe Keypad enable Power lock enable Valet mode Power point max time/time out Approach detection Welcome mat enable/disable Tire pressure Police dark car
Battery Energy Control Module B (BECMB)	723	Yes	Yes	No	None
CCM	764	Yes	Yes	Radar horizontal and vertical alignment calibration	None
DSP	783	Yes	Yes	No	None
DACMC (integrated with ACM)	7D5	Yes	Yes	No	None
DC/ DC Converter Control Module (Voltage Quality Module [VQM])	746	Yes	Yes	No	None
DDM	740	Yes	Yes	Windows initialization	None
DSM	744	Yes	Yes	No	None
SCME	776	Yes	Yes	No	High heat initial setpoint High heat final setpoint
FCIM	7A7	Yes	Yes	No	None
GWM	716	Yes	Yes	No	None
GSM	732	No	No	No	None
HCM	734	Yes	No	No	None
HUD module	7B2	No	No	No	None
HSWM	714	Yes	Yes	No	None
IPC	720	Yes	Yes	No	Auto lock enable/disable Auto unlock enable/disable
IPMA module	706	Yes	Yes	Camera calibration	None
OCSM	765	No	No	OCSM re-zero	None
PAM (integrated with BCM)	736	Yes	Yes	No	None
PSCM	730	Yes	Yes	No	None
PCM	7E0	Yes	Yes	Misfire Monitor Neutral Profile Correction procedure	None
PDM	741	Yes	Yes	Windows initialization	None
RTM	751	Yes	Yes	No	None
RGTM	775	Yes	Yes	Power liftgate (by self-test or manual procedure)	None
RCM	737	Yes	Yes	No	None
SODL	7C4	Yes	Yes	No	BLIS and CTA enable
SODR	7C6	Yes	Yes	No	BLIS and CTA enable
SCCM	724	Yes	Yes	No	None
TRCM	711	No	Yes	No	None
TRM	791	Yes	Yes	No	Inoperative LED Right turn/stop lamp Left turn/stop lamp Park lamp
TCU	754	Yes	Yes	No	None
VDM	721	Yes	Yes	Suspension height sensor calibration	None

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

• You smell fuel, burning insulation, or see smoke.

• Brakes feel soft, pull hard to one side, or make grinding noises.

• The engine overheats, stalls repeatedly, or misfires under load.

• You are missing required tools, torque specs, or safe lifting equipment.

• You are not confident in the next step or safety outcome.

Safety Warning

Module Configuration and Parameter Chart

Use the Manual With the Right Hardware

When to See a Mechanic

Rather have a pro handle this?