Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2012 Lincoln MKT Base, FWDFACTORY OEM SERVICE PROCEDURE
Seat System DTCS
DRIVER DOOR MODULE (DDM) DIAGNOSTIC TROUBLE CODE (DTC) LIST
| DTC | Description | Action |
|---|---|---|
| B1534 | Memory 1 Switch Circuit Short to Ground | GO to PINPOINT TEST D . |
| B1538 | Memory 2 Switch Circuit Short to Ground | GO to PINPOINT TEST D . |
| All Other DTCs | - | REFER to MULTIFUNCTION ELECTRONIC MODULES . |
DRIVER SEAT MODULE (DSM) DIAGNOSTIC TROUBLE CODE (DTC) LIST
| DTC | Description | Action |
|---|---|---|
| B106E | Solid State Driver Disabled Due to Short Circuit | GO to PINPOINT TEST CB . |
| B106F | Module Disabled Due to External Fault | GO to PINPOINT TEST CB . |
| B1317 | Battery Voltage High | GO to PINPOINT TEST CE . |
| B1318 | Battery Voltage Low | GO to PINPOINT TEST CA . |
| B1342 | ECU Is Faulted | CLEAR the DTCs. REPEAT the self-test. If DTC B1342 is retrieved again, INSTALL a new Driver Seat Module (DSM). REFER to DRIVER SEAT MODULE (DSM) . TEST the system for normal operation. |
| B1663 | Seat Driver Front Up/Down Motor Stalled | If the motor does not operate, GO to PINPOINT TEST A . If motor operates, GO to PINPOINT TEST D . |
| B1664 | Seat Driver Rear Up/Down Motor Stalled | If the motor does not operate, GO to PINPOINT TEST A . If motor operates, GO to PINPOINT TEST D . |
| B1665 | Seat Driver Forward/Backward Motor Stalled | If the motor does not operate, GO to PINPOINT TEST A . If motor operates, GO to PINPOINT TEST D . |
| B1666 | Seat Driver Recline Motor Stalled | If the motor does not operate, GO to PINPOINT TEST A . If motor operates, GO to PINPOINT TEST D . |
| B1669 | Mirror Passenger Up/Down Motor Stalled | REFER to REAR VIEW MIRRORS . |
| B1703 | Seat Driver Recline Forward Switch Circuit Short to Battery | GO to PINPOINT TEST A . |
| B1707 | Seat Driver Recline Rearward Switch Circuit Short to Battery | GO to PINPOINT TEST A . |
| B1711 | Seat Driver Front Up Switch Circuit Short to Battery | GO to PINPOINT TEST A . |
| B1715 | Seat Driver Front Down Switch Circuit Short to Battery | GO to PINPOINT TEST A . |
| B1719 | Seat Driver Forward Switch Circuit Short to Battery | GO to PINPOINT TEST A . |
| B1723 | Seat Driver Rearward Switch Circuit Short to Battery | GO to PINPOINT TEST A . |
| B1727 | Seat Driver Rear Up Switch Circuit Short to Battery | GO to PINPOINT TEST A . |
| B1731 | Seat Driver Rear Down Switch Circuit Short to Battery | GO to PINPOINT TEST A . |
| B1952 | Seat Rear Up/Down Position Feedback Circuit Short to Battery | GO to PINPOINT TEST D . |
| B1953 | Seat Rear Up/Down Position Feedback Circuit Short to Ground | GO to PINPOINT TEST D . |
| B1956 | Seat Front Up/Down Position Feedback Circuit Short to Battery | GO to PINPOINT TEST D . |
| B1957 | Seat Front Up/Down Position Feedback Circuit Short to Ground | GO to PINPOINT TEST D . |
| B1960 | Seat Recline Forward/Backward Position Feedback Circuit Short to Battery | GO to PINPOINT TEST D . |
| B1961 | Seat Recline Forward/Backward Position Feedback Circuit Short to Ground | GO to PINPOINT TEST D . |
| B1964 | Seat Horizontal Forward/Rearward Position Feedback Circuit Short to Battery | GO to PINPOINT TEST D . |
| B1965 | Seat Horizontal Forward/Rearward Position Feedback Circuit Short to Ground | GO to PINPOINT TEST D . |
| B1987 | Pedal Forward/Rearward Motor Stalled | REFER to HYDRAULIC BRAKE ACTUATION . |
| B1988 | Pedal Position Forward Switch Circuit Short to Battery | REFER to HYDRAULIC BRAKE ACTUATION . |
| B1989 | Pedal Position Rearward Switch Circuit Short to Battery | REFER to HYDRAULIC BRAKE ACTUATION . |
| B1991 | Pedal Forward/Rearward Potentiometer Feedback Circuit Short to Battery | REFER to HYDRAULIC BRAKE ACTUATION . |
| B2224 | Mirror Passenger Drive Circuit Failure | REFER to REAR VIEW MIRRORS . |
| B2275 | Pedal Forward/Rearward Pot. Feedback Ckt. Short to GND | REFER to HYDRAULIC BRAKE ACTUATION . |
| B2312 | Mirror Passenger Horizontal Feedback Potentiometer Circuit Failure | REFER to REAR VIEW MIRRORS . |
| B2314 | Mirror Passenger Horizontal Feedback Potentiometer Circuit Short to Battery | REFER to REAR VIEW MIRRORS . |
| B2316 | Mirror Passenger Vertical Feedback Potentiometer Circuit Failure | REFER to REAR VIEW MIRRORS . |
| B2318 | Mirror Passenger Vertical Feedback Potentiometer Circuit Short to Battery | REFER to REAR VIEW MIRRORS . |
| B2330 | Column Reach Feedback Potentiometer Circuit Short To Battery | REFER to STEERING COLUMN . |
| B2331 | Column Reach Feedback Potentiometer Circuit Short To Ground | REFER to STEERING COLUMN . |
| B2334 | Column Tilt Feedback Potentiometer Circuit Short To Battery | REFER to STEERING COLUMN . |
| B2335 | Column Tilt Feedback Potentiometer Circuit Short To Ground | REFER to STEERING COLUMN . |
| B2340 | Column Reach Motor Stalled | REFER to STEERING COLUMN . |
| B2341 | Column Tilt Motor Stalled | REFER to STEERING COLUMN . |
| B2477 | Module Configuration Failure | REFER to MODULE CONFIGURATION . |
| B2A41 | Steering Column Telescopic Rear Switch Short To Battery | REFER to STEERING COLUMN . |
| B2A42 | Steering Column Tilt Up Switch Short To Battery | REFER to STEERING COLUMN . |
| B2A44 | Steering Column Telescopic Forward Switch Short To Battery | REFER to STEERING COLUMN . |
| U0140 | Lost Communication With Body Control Module (GEM) | GO to PINPOINT TEST CC . |
| U0155 | Lost Communication With Instrument Panel Cluster (IC) Control Module | GO to PINPOINT TEST CD . |
| U2050 | No Application Present | REFER to MODULE CONFIGURATION . |
DUAL CLIMATE CONTROLLED SEAT MODULE (DCSM) DIAGNOSTIC TROUBLE CODE (DTC) LIST
| DTC | Description | Action |
|---|---|---|
| B103B | Thermoelectric Driver Overcurrent Low | GO to PINPOINT TEST AB . |
| B103C | Thermoelectric Driver Open Load | GO to PINPOINT TEST AC . |
| B103D | Blower Driver Overtemperature | GO to PINPOINT TEST AD . |
| B1111 | Driver Thermo Electric Device Control Overtemperature Fault | GO to PINPOINT TEST AB . |
| B1113 | Passenger Thermo Electric Device Control Overtemperature Fault | GO to PINPOINT TEST AE . |
| B111B | Passenger Thermoelectric Driver Overcurrent Low | GO to PINPOINT TEST AE . |
| B111C | Passenger Thermoelectric Driver Open Load | GO to PINPOINT TEST AF . |
| B111D | Passenger Blower Driver Overtemperature | GO to PINPOINT TEST AG . |
| B1342 | ECU is Faulted | INSTALL a new Dual Climate Controlled Seat Module (DCSM). REFER to DUAL CLIMATE CONTROLLED SEAT MODULE (DCSM) . |
| B19A1 | Passenger Seat Cushion Blower Speed Short to Battery | GO to PINPOINT TEST AH . |
| B19A2 | Passenger Seat Back Blower Speed Short to Battery | GO to PINPOINT TEST AI . |
| B19A3 | Driver Seat Cushion Blower Speed Short to Battery | GO to PINPOINT TEST AJ . |
| B19A4 | Driver Seat Back Blower Speed Short to Battery | GO to PINPOINT TEST AK . |
| B19A5 | Passenger Seat Cushion Blower Speed Short to Ground | GO to PINPOINT TEST AL . |
| B19A6 | Passenger Seat Back Blower Speed Short to Ground | GO to PINPOINT TEST AM . |
| B19A7 | Driver Seat Cushion Blower Speed Short to Ground | GO to PINPOINT TEST AN . |
| B19A8 | Driver Seat Back Blower Speed Short to Ground | GO to PINPOINT TEST AO . |
| B2477 | Module Configuration Failure |
NOTE:
This DTC indicates PMI has not been done to a newly installed module or configuration data has been lost. CARRY OUT Programmable Module Installation (PMI) on the DCSM. REFER to
MODULE CONFIGURATION
. REPEAT the self-test. If PMI is successful, the DTC will not be present. |
| B2486 | Climate Control Seat Module Voltage Out of Range | GO to PINPOINT TEST AA . |
| B2729 | Cushion Over-Temp Detected | GO to PINPOINT TEST AP . |
| B272A | Passenger Cushion Over-Temp Detected | GO to PINPOINT TEST AQ . |
| B272B | Passenger Back Over-Temp Detected | GO to PINPOINT TEST AR . |
| B272C | Driver Differential Temperature Fault | GO to PINPOINT TEST AS . |
| B272D | Passenger Differential Temperature Fault | GO to PINPOINT TEST AT . |
| B272E | Driver Ignition Run/Blower Circuit Short to Ground (this DTC sets for an open or short to voltage) | GO to PINPOINT TEST AU . |
| B272F | Passenger Ignition Run/Blower Circuit Short to Ground (this DTC sets for an open or short to voltage) | GO to PINPOINT TEST AV . |
| B2730 | Back Over-Temp Detected | GO to PINPOINT TEST AW . |
| U2050 | No Application Present | INSTALL a new DCSM. REFER to DUAL CLIMATE CONTROLLED SEAT MODULE (DCSM) . REPEAT the self-test. |
| All Other DTCs | - | REFER to MULTIFUNCTION ELECTRONIC MODULES . |
PASSENGER CLIMATE CONTROLLED SEAT MODULE - 2 (PCSM-2) DIAGNOSTIC TROUBLE CODE (DTC) LIST
| DTC | Description | Action |
|---|---|---|
| B103B | Thermoelectric Driver Overcurrent Low | GO to PINPOINT TEST AX . |
| B103C | Thermoelectric Driver Open Load | GO to PINPOINT TEST AY . |
| B103D | Blower Driver Overtemperature | GO to PINPOINT TEST AZ . |
| B1111 | Driver Thermo Electric Device Control Overtemperature Fault | GO to PINPOINT TEST AX . |
| B1113 | Passenger Thermo Electric Device Control Overtemperature Fault | GO to PINPOINT TEST BA . |
| B111B | Passenger Thermoelectric Driver Overcurrent Low | GO to PINPOINT TEST BA . |
| B111C | Passenger Thermoelectric Driver Open Load | GO to PINPOINT TEST BB . |
| B111D | Passenger Blower Driver Overtemperature | GO to PINPOINT TEST BC . |
| B1342 | ECU is Faulted | INSTALL a new Passenger Climate Controlled Seat Module - 2 (PCSM-2). REFER to PASSENGER CLIMATE - CONTROLLED SEAT MODULE (PCSM-2) . |
| B19A1 | Passenger Seat Cushion Blower Speed Short to Battery | GO to PINPOINT TEST BD . |
| B19A2 | Passenger Seat Back Blower Speed Short to Battery | GO to PINPOINT TEST BE . |
| B19A3 | Driver Seat Cushion Blower Speed Short to Battery | GO to PINPOINT TEST BF . |
| B19A4 | Driver Seat Back Blower Speed Short to Battery | GO to PINPOINT TEST BG . |
| B19A5 | Passenger Seat Cushion Blower Speed Short to Ground | GO to PINPOINT TEST BH . |
| B19A6 | Passenger Seat Back Blower Speed Short to Ground | GO to PINPOINT TEST BI . |
| B19A7 | Driver Seat Cushion Blower Speed Short to Ground | GO to PINPOINT TEST BJ . |
| B19A8 | Driver Seat Back Blower Speed Short to Ground | GO to PINPOINT TEST BK . |
| B2477 | Module Configuration Failure |
NOTE:
This DTC indicates PMI has not been done to a newly installed module or configuration data has been lost. CARRY OUT Programmable Module Installation (PMI) on the PCSM-2. REFER to
MODULE CONFIGURATION
. REPEAT the self-test. If PMI is successful, the DTC will not be present. |
| B2486 | Climate Control Seat Module Voltage Out of Range | GO to PINPOINT TEST AA . |
| B2729 | Cushion Over-Temp Detected | GO to PINPOINT TEST BL . |
| B272A | Passenger Cushion Over-Temp Detected | GO to PINPOINT TEST BM . |
| B272B | Passenger Back Over-Temp Detected | GO to PINPOINT TEST BN . |
| B272C | Driver Differential Temperature Fault | GO to PINPOINT TEST BO . |
| B272D | Passenger Differential Temperature Fault | GO to PINPOINT TEST BP . |
| B272E | Driver Ignition Run/Blower Circuit Short to Ground (this DTC sets for an open or short to voltage) | GO to PINPOINT TEST BQ . |
| B272F | Passenger Ignition Run/Blower Circuit Short to Ground (this DTC sets for an open or short to voltage) | GO to PINPOINT TEST BR . |
| B2730 | Back Over-Temp Detected | GO to PINPOINT TEST BS . |
| U2050 | No Application Present | INSTALL a new PCSM-2. REFER to PASSENGER CLIMATE - CONTROLLED SEAT MODULE (PCSM-2) . |
| All Other DTCs | - | REFER to MULTIFUNCTION ELECTRONIC MODULES . |
REAR HEATING VENTILATION AIR CONDITIONING (RHVAC) DIAGNOSTIC TROUBLE CODE (DTC) LIST
| DTC | Description | Action |
|---|---|---|
| B1031:11 | Left Rear Seat Heater: Circuit Short To Ground | GO to PINPOINT TEST M . |
| B1031:12 | Left Rear Seat Heater: Circuit Short To Battery | GO to PINPOINT TEST M . |
| B1031:13 | Left Rear Seat Heater: Circuit Open | GO to PINPOINT TEST M . |
| B1033:11 | Right Rear Seat Heater: Circuit Short To Ground | GO to PINPOINT TEST N . |
| B1033:12 | Right Rear Seat Heater: Circuit Short To Battery | GO to PINPOINT TEST N . |
| B1033:13 | Right Rear Seat Heater: Circuit Open | GO to PINPOINT TEST N . |
SMART JUNCTION BOX (SJB) DIAGNOSTIC TROUBLE CODE (DTC) LIST
| DTC | Description | Action |
|---|---|---|
| B2794 | 3rd Row Power Fold Circuit Failure | If the third row power-fold seats do not operate, GO to PINPOINT TEST BT . If the third row power-fold seats do operate, REPAIR the Power-Fold Seat Module (PFSM) enable circuit CPS58 (WH/BN) for a short to voltage. CLEAR the DTCs. REPEAT the self-test. TEST the system for normal operation. |
| B2A2D | 3rd Row Power Fold Circuit Short to Ground | GO to PINPOINT TEST BT . |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
