Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2008 Lincoln Navigator L RWDFACTORY OEM SERVICE PROCEDURE
Vehicle Dynamic Systems DTCS
ABS MODULE DIAGNOSTIC TROUBLE CODE (DTC) LIST
| DTC | Description | Source | Perform Test |
|---|---|---|---|
| B1483 | Brake Pedal Input Circuit Failure | ABS Module | Go to Pinpoint Test A . |
| B1676 | Battery Pack Voltage Out of Range | ABS Module | Go to Pinpoint Test B . |
| B2900 | VIN Mismatch | ABS Module | Go to Pinpoint Test E . |
| C1095 | ABS Hydraulic Pump Motor Circuit Failure | ABS Module | Go to Pinpoint Test C . |
| C1145 | Wheel Speed Sensor RF Input Circuit Failure | ABS Module | Go to Pinpoint Test D . |
| C1155 | Wheel Speed Sensor LF Input Circuit Failure | ABS Module | Go to Pinpoint Test D . |
| C1165 | Wheel Speed Sensor RR Input Circuit Failure | ABS Module | Go to Pinpoint Test D . |
| C1175 | Wheel Speed Sensor LR Input Circuit Failure | ABS Module | Go to Pinpoint Test D . |
| C1233 | Wheel Speed LF Input Signal Missing | ABS Module | Go to Pinpoint Test K . |
| C1234 | Wheel Speed RF Input Signal Missing | ABS Module | Go to Pinpoint Test K . |
| C1235 | Wheel Speed RR Input Signal Missing | ABS Module | Go to Pinpoint Test K . |
| C1236 | Wheel Speed LR Input Signal Missing | ABS Module | Go to Pinpoint Test K . |
| C1277 | Steering Wheel Angle 1 and 2 Circuit Failure | ABS Module | Go to Pinpoint Test F . |
| C1278 | Steering Wheel Angle 1 and 2 Signal Faulted | ABS Module | Go to Pinpoint Test F . |
| C1279 | Yaw Rate Sensor Circuit Failure | ABS Module | Go to Pinpoint Test G . |
| C1280 | Yaw Rate Sensor Signal Fault | ABS Module | Go to Pinpoint Test G . |
| C1281 | Lateral Accelerometer Circuit Failure | ABS Module | Go to Pinpoint Test G . |
| C1282 | Lateral Accelerometer Signal Fault | ABS Module | Go to Pinpoint Test G . |
| C1285 | Booster Solenoid Circuit Failure | ABS Module | Go to Pinpoint Test H . |
| C1287 | Booster Pedal Force Switch Circuit Failure | ABS Module | Go to Pinpoint Test I . |
| C1470 | TCSa Function Disabled (brake fluid temperature is above a pre-set limit) | ABS Module | ALLOW the brake fluid time to cool. CLEAR the DTC. TEST DRIVE the vehicle and VERIFY ABS operation. |
| C1516 | Roll Rate Sensor Signal Fault | ABS Module | Go to Pinpoint Test G . |
| C1517 | Roll Rate Sensor Circuit Failure | ABS Module | Go to Pinpoint Test G . |
| C1963 | Stability Assist Inhibit Warning | ABS Module |
NOTE:
This DTC will not clear until the vehicle has been driven above 48 km/h (30 mph) with input from the steering wheel rotation sensor. Go to Pinpoint Test F
. |
| C1996 | Active Yaw and/or Roll Control Disabled | ABS Module | Go to Pinpoint Test J . |
| C2769 - vehicles with Roll Stability Control (RSC®) | Longitudinal Acceleration Sensor Electrical Failure (sensor cluster fault) | ABS Module | Go to Pinpoint Test G . |
| C2770 - vehicles with RSC® | Longitudinal Acceleration Sensor Plausibility Failure (sensor cluster fault) | ABS Module | Go to Pinpoint Test G . |
| C2777 | Sensor Cluster Bus Failure | ABS Module | Go to Pinpoint Test G . |
| C2778 | Sensor Cluster Power Supply Failure | ABS Module | Go to Pinpoint Test G . |
| U1901 | CAN Network #2 Communication Bus Fault | ABS Module | Go to Pinpoint Test G . |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
