Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2007 Lincoln Navigator RWDFACTORY OEM SERVICE PROCEDURE
Engine Mechanical: Mechanical: Engine: Assembly: Engine
Special Tools
| Illustration | Tool Name | Tool Number |
|---|---|---|
| Remover/Installer, Cylinder Head | 303-572 (T97T-6000-A) | |
| Installer, Connecting Rod | 303-442 (T93P-6136-A) | |
| Compressor, Valve Spring | 303-1039 | |
| Installer, Crankshaft Vibration Damper | 303-102 (T74P-6316-B) | |
| Installer, Crankshaft Front Seal | 303-635 | |
| Installer, Front Cover Seal | 303-335 (T88T-6701-A) | |
| Compressor, Piston Ring | 303-D032 (D81L-6002-C) or equivalent | |
| Installer, Crankshaft Rear Seal | 303-518 (T95P-6701-DH) | |
| Installer, Crankshaft Oil Slinger | 303-517 (T95P-6701-CH) | |
| Installer, Crankshaft Rear Seal | 303-516 (T95P-6701-EH) | |
| Impact Slide Hammer | 100-001 (T50T-100-A) | |
| Alignment Pins, Cylinder Head | 303-1040 (SR-015486) | |
| Modular Engine Lift Bracket | 303-F047 (014-00073) or equivalent | |
| Locking Tool, Camshaft Phaser Sprocket | 303-1046 |
Material
| Item | Specification |
|---|---|
| Motorcraft Metal Surface Prep ZC-31 |
- |
| Silicone Gasket Remover ZC-30 |
- |
| Silicone Gasket and Sealant TA-30 |
WSE-M4G323-A4 |
| Motorcraft SAE 5W-20 Premium Synthetic Blend Motor Oil XO-5W20-QSP (US); Motorcraft SAE 5W-20 Super Premium Motor Oil CXO-5W20-LSP12 (Canada); or equivalent |
WSS-M2C930-A |
| Motorcraft Premium Gold Engine Coolant with Bittering Agent (US only) VC-7-B (US); CVC-7-A (Canada); or equivalent (yellow color) |
WSS-M97B51-A1 |
| Hydraulic Chain Tensioner Retaining Clip 1L3Z-6P250-AA |
- |
| Item | Part Number | Description |
|---|---|---|
| 1 | 12B637 | Engine wiring harness |
| 2 | 6A505 | Valve cover - LH |
| 3 | 6750 | Oil level indicator |
| 4 | N605892 | Oil level indicator tube bolt |
| 5 | 6K873 | Oil level indicator tube |
| 6 | N807834 | Camshaft bearing cap bolt (10 required) |
| 7 | 6B280 | Camshaft bearing cap (4 required) |
| 8 | 6C255 | Camshaft - LH |
| 9 | 6529 | Roller follower (24 required) |
| 10 | 6518 | Valve spring retainer key (48 required) |
| 11 | 6514 | Valve spring retainer (24 required) |
| 12 | 6513 | Valve spring (24 required) |
| 13 | 6A517 | Valve stem seal (24 required) |
| 14 | 6C501 | Hydraulic lash adjuster (24 required) |
| 15 | 6279 | Camshaft phaser sprocket bolt - LH |
| 16 | 6C524 | Camshaft phaser sprocket - LH |
| 17 | 6B284 | Camshaft bearing cap |
| 18 | 12405 | Spark plug (4 required) |
| 19 | 12A366 | Ignition coil (4 required) |
| 20 | 6065 | Cylinder head bolt (20 required) |
| 21 | W707747 | Exhaust manifold stud (8 required) |
| 22 | 9Y431 | Exhaust manifold gaskets (2 required) |
| 23 | 9431 | Exhaust manifold - LH |
| 24 | W701706 | Exhaust manifold nut (8 required) |
| 25 | 6507 | Intake valve (16 required) |
| 26 | 6505 | Exhaust valve (8 required) |
| 27 | 6083 | Cylinder head gasket - LH |
| 28 | W701520 | Variable camshaft timing (VCT) oil control solenoid assembly bolt (2 required) |
| 29 | 6C261 | VCT oil control solenoid assembly |
| 30 | 6050 | Cylinder head - LH |
| 31 | 14B102 | Cylinder head temperature (CHT) sensor jumper harness |
| 32 | W701571 | Heater outlet tube stud bolt |
| 33 | 18663 | Heater outlet tube |
| 34 | 6051 | Cylinder head gasket - RH |
| 35 | 6049 | Cylinder head - RH |
| 36 | 9Y431 | Exhaust manifold gasket (2 required) |
| 37 | 9430 | Exhaust manifold - RH |
| 38 | W701706 | Exhaust manifold nut (8 required) |
| 39 | W707747 | Exhaust manifold stud (8 required) |
| 40 | 6C260 | VCT oil control solenoid assembly |
| 41 | W701520 | VCT oil control solenoid assembly bolt (2 required) |
| 42 | 6279 | Camshaft phaser sprocket bolt - RH |
| 43 | 6C524 | Camshaft phaser sprocket - RH |
| 44 | 6B284 | Camshaft bearing cap |
| 45 | N807834 | Camshaft bearing cap bolt (10 required) |
| 46 | 6B280 | Camshaft bearing cap (4 required) |
| 47 | 6251 | Camshaft - RH |
| 48 | 12405 | Spark plug (4 required) |
| 49 | 12A366 | Ignition coil (4 required) |
| 50 | W706175 | Ignition coil bolt (8 required) |
| 51 | 6582 | Valve cover - RH |
| 52 | 6765 | Oil fill adapter |
| 53 | 6766 | Oil fill adapter cap |
| 54 | 6758 | Crankcase ventilation tube |
| 55 | W503282 | Coolant crossover tube bolt (3 required) |
| 56 | W503279 | Thermostat housing bolt (2 required) |
| 57 | 8594 | Thermostat housing |
| 58 | N806807 | Thermostat O-ring seal |
| 59 | 8575 | Thermostat |
| 60 | 8C369 | Coolant crossover tube |
| 61 | 9A474 | Intake manifold vacuum tube and support bracket |
| 62 | W709775 | Intake manifold bolt (10 required) |
| 63 | 9Y451 | Intake manifold assembly |
| 64 | 6K817 | Positive crankcase ventilation (PCV) tube |
| 65 | W500204 | PCV heater element assembly bolt (2 required) |
| 66 | 9F624 | PCV heater element assembly |
| Item | Part Number | Description |
|---|---|---|
| 1 | N804758 | Radio ignition interference capacitor nut |
| 2 | 18801 | Radio ignition interference capacitor |
| 3 | 6C086 | Engine front cover |
| 4 | W503282 | Timing chain guide bolt- RH (2 required) |
| 5 | 6L266 | Timing chain tensioner - RH |
| 6 | N606543 | Timing chain tensioner bolt - RH (2 required) |
| 7 | 6268 | Timing chain - RH |
| 8 | 6M256 | Timing chain guide - RH |
| 9 | N606543 | Timing chain tensioner bolt - LH (2 required) |
| 10 | 6M269 | Timing chain tensioner - LH |
| 11 | 6M274 | Tensioner arm - LH |
| 12 | N605892 | Timing chain guide upper bolt - LH |
| 13 | 6306 | Crankshaft sprocket |
| 14 | 6B274 | Timing chain guide - LH |
| 15 | N606527 | Timing chain guide lower bolt - LH |
| 16 | 6268 | Timing Chain - LH |
| 17 | 6K255 | Tensioner arm - RH |
| 18 | 12A227 | Ignition pulse wheel |
| 19 | W707225 | Power steering pump stud bolt |
| 20 | W706447 | Power steering pump bolt (2 required) |
| 21 | 3A696 | Power steering pump assembly |
| 22 | W706605 | Engine front cover bolt |
| 23 | N808529 | Engine front cover stud bolt (2 required) |
| 24 | N806177 | Engine front cover bolt (9 required) |
| 25 | 6C315 | Crankshaft position (CKP) sensor |
| 26 | N806155 | CKP sensor bolt |
| 27 | 19A216 | Accessory drive belt idler pulley |
| 28 | N808102 | Accessory drive belt idler pulley bolt |
| 29 | 6700 | Crankshaft front seal |
| 30 | 6316 | Crankshaft pulley |
| 31 | N806165 | Crankshaft pulley washer |
| 32 | W701512 | Crankshaft pulley bolt |
| 33 | 8A528 | Coolant pump pulley |
| 34 | N806282 | Coolant pump pulley bolt (4 required) |
| 35 | N808794 | Coolant pump bolt (4 required) |
| 36 | 8501 | Coolant pump |
| 37 | N808102 | Accessory drive belt idler pulley bolt |
| 38 | 19A216 | Accessory drive belt idler pulley |
| 39 | N806155 | Camshaft position (CMP) sensor bolt (2 required) |
| 40 | 6B288 | CMP sensor (2 required) |
| 41 | W709573 | Engine front cover stud bolt (3 required) |
| Item | Part Number | Description |
|---|---|---|
| 1 | 6150 | Upper compression ring (8 required) |
| 2 | 6152 | Lower compression ring (8 required) |
| 3 | 6159 | Outer oil control ring (8 required) |
| 4 | 6161 | Inner oil control ring (8 required) |
| 5 | 6159 | Outer oil control ring (8 required) |
| 6 | 6140 | Piston pin retainer (16 required) |
| 7 | 6135 | Piston pin (8 required) |
| 8 | 6110 | Piston (8 required) |
| 9 | 6200 | Connecting rod assembly (8 required) |
| 10 | 6211 | Connecting rod bearing (8 required) |
| 11 | 6K318 | Crankshaft rear seal retainer plate |
| 12 | N806155 | Crankshaft rear seal retainer plate bolt (6 required) |
| 13 | 6310 | Crankshaft rear seal |
| 14 | 6701 | Crankshaft oil slinger |
| 15 | 6375 | Flexplate |
| 16 | N806168 | Flexplate bolt (8 required) |
| 17 | 6714 | Oil filter |
| 18 | 6890 | Oil filter threaded adapter |
| 19 | N806156 | Oil filter adapter bolt (4 required) |
| 20 | 9278 | Engine oil pressure (EOP) switch |
| 21 | 6881 | Oil filter adapter |
| 22 | 6A636 | Oil filter adapter gasket |
| 23 | W701605 | Oil pan bolt (16 required) |
| 24 | 6675 | Oil pan |
| 25 | 6710 | Oil pan gasket |
| 26 | N605904 | Oil pump screen and pickup tube bolt |
| 27 | N806155 | Oil pump screen and pickup tube bolt (2 required) |
| 28 | 6622 | Oil pump screen and pickup tube |
| 29 | N806180 | Oil pump screen and pickup tube spacer |
| 30 | 6K258 | Crankshaft main bearing cap stud |
| 31 | 6345 | Crankshaft main bearing cap bolt (9 required) |
| 32 | 6A346 | Crankshaft main bearing dowel (10 required) |
| 33 | 6C357 | Crankshaft main bearing cap bolt (10 required) |
| 34 | 6325 | Crankshaft main bearing cap (5 required) |
| 35 | 6A338 | Crankshaft bearing - lower (5 required) |
| 36 | 6K302 | Crankshaft thrust washer - lower |
| 37 | 6303 | Crankshaft |
| 38 | N806201 | Crankshaft key |
| 39 | 6A341 | Crankshaft thrust washer - upper (2 required) |
| 40 | 6333 | Crankshaft bearing - upper (4 required) |
| 41 | 6W337 | Crankshaft bearing - upper |
| 42 | 6210 | Connecting rod cap (8 required) |
| 43 | 6211 | Connecting rod bearing (8 required) |
| 44 | 6621 | Oil pump |
| 45 | N806183 | Oil pump bolt (3 required) |
| 46 | 6010 | Cylinder block |
| 47 | W500225 | Knock sensor bolt (2 required) |
| 48 | 12A699 | Knock sensor (2 required) |
All vehicles
- Record the main bearing code found on the front of the engine block.
- Record the main bearing code found on the back of the crankshaft.
- Using the data recorded earlier and the Bearing Select Fit Chart, Standard Bearings, determine the required bearing grade for each main bearing.
- Read the first letter of the engine block main bearing code and the first letter of the crankshaft main bearing code.
- Read down the column below the engine block main bearing code letter, and across the row next to the crankshaft main bearing code letter, until the 2 intersect. This is the required bearing grade for the number one crankshaft main bearing.
- As an example, if the engine block code letter is "F" and the crankshaft code letter is "D", the correct bearing grade for this main bearing is a "2".
- Repeat this process for the remaining 4 main bearings.
- If oversize bearings are being used, use the procedure in the previous step and the Bearing Select Fit Chart, Oversize Bearings to determine the required bearing grade for each main bearing.
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
