Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2005 Lincoln Town Car Protection SeriesFACTORY OEM SERVICE PROCEDURE
Anti-Lock Control DTCS
ANTI-LOCK BRAKE SYSTEM (ABS) MODULE DIAGNOSTIC TROUBLE CODE (DTC) LIST
| DTCS | Source | Description | Perform Test |
|---|---|---|---|
| B1342 | ABS Module | ECU is Defective | CLEAR the DTCs. RETRIEVE the DTCs. REPEAT the self-test. If DTC B1342 is retrieved again, INSTALL a new ABS module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE . REPEAT the self-test. |
| B1484 | ABS Module | Brake Pedal Input Open Circuit | Go to PINPOINT TEST D . |
| B1596 | ABS Module | Service Continuous Codes | TURN the ignition switch from OFF to ON. REPEAT the ABS self-test. If any DTCs are retrieved, REFER to the ANTI-LOCK BRAKE SYSTEM (ABS) MODULE DIAGNOSTIC TROUBLE CODE (DTC) INDEX . If no DTCs are retrieved, CARRY OUT a drive test above 15 km/h (9 mph), then REFER to the SYMPTOM CHART . |
| B1676 | ABS Module | Battery Voltage Out of Range | Go to PINPOINT TEST E . |
| C1145 | ABS Module | RF Anti-Lock Brake Sensor Input Circuit Failure | Go to PINPOINT TEST B . |
| C1155 | ABS Module | LF Anti-Lock Brake Sensor Input Circuit Failure | Go to PINPOINT TEST B . |
| C1165 | ABS Module | RR Anti-Lock Brake Sensor Input Circuit Failure | Go to PINPOINT TEST B . |
| C1175 | ABS Module | LR Anti-Lock Brake Sensor Input Circuit Failure | Go to PINPOINT TEST B . |
| C1222 | ABS Module | Mismatched Wheels or Damaged Wheel Speed Sensor Ring | Make sure the tires are the same size and correctly inflated. INSPECT the wheel speed sensor rings. CLEAR the DTCs. TEST drive the vehicle. REPEAT the self-test. |
| C1266 | ABS Module | ABS Valve Power Relay Circuit Failure | Go to PINPOINT TEST J . |
| C1296 | ABS Module | LF Anti-Lock Brake Sensor Input Signal Missing | Go to PINPOINT TEST C . |
| C1297 | ABS Module | RF Anti-Lock Brake Sensor Input Signal Missing | Go to PINPOINT TEST C . |
| C1298 | ABS Module | RR Anti-Lock Brake Sensor Input Signal Missing | Go to PINPOINT TEST C . |
| C1299 | ABS Module | LR Anti-Lock Brake Sensor Input Signal Missing | Go to PINPOINT TEST C . |
| C1300 | ABS Module | ABS Hydraulic Pump Motor Circuit Failure | Go to PINPOINT TEST A . |
| C1805 | ABS Module | PCM and ABS Modules Do Not Match | CHECK the part numbers. INSTALL the correct module. REFER to ELECTRONIC ENGINE CONTROLS . |
| C2775 | ABS Module | TC ON/OFF Switch Stuck Failure | Go to PINPOINT TEST H . |
| U0073 | Instrument Cluster | Control Module Communication Bus Off | REFER to MODULE COMMUNICATIONS NETWORK . |
| U1900 | PCM | CAN Communication Bus Fault -Receive Error | REFER to MODULE COMMUNICATIONS NETWORK . |
| U2023 | Instrument Cluster | Fault Received From External Node | REFER to MODULE COMMUNICATIONS NETWORK . |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
