Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2005 Lincoln Aviator AWDFACTORY OEM SERVICE PROCEDURE
Climate Controlled Seat Module DTCS (CCSM)
CLIMATE CONTROLLED SEAT MODULE (CCSM) DIAGNOSTIC TROUBLE CODE (DTC) LIST
| DTC | Description | Source | Action |
|---|---|---|---|
| B1342 | ECU Is Faulted | CCSM | INSTALL a new CCSM and CARRY OUT programmable module installation (PMI). REFER to FRONT SEAT CUSHION . |
| B1358 | Ignition Switch or Blower Electronics Circuit Short to Ground | CCSM | GO to PINPOINT TEST J . |
| B2477 | Module Configuration Error | CCSM | This DTC indicates programmable module installation (PMI) has not been done to a newly installed module. CARRY OUT PMI. REFER to MODULE CONFIGURATION . CLEAR the DTC. CARRY OUT the self-test. |
| B2486 | Climate Controlled Seat Module Voltage Out of Range | CCSM | DEPOWER the supplemental restraint system (SRS). Refer to SUPPLEMENTAL RESTRAINT SYSTEM . DISCONNECT driver seat C327 or passenger seat C315 of the affected seat and CONNECT restraint system diagnostic tool 501-095 to the affected seat connector. CONNECT the battery ground cable. CHECK circuit 294 (WH/LB) for a fault and REPAIR as needed. If OK, REFER to CHARGING SYSTEM - GENERAL INFORMATION . Once the repair is complete, DISCONNECT the restraint system diagnostic tool from the seat connector and CONNECT the seat connector of the affected seat. REPOWER the SRS. Refer to SUPPLEMENTAL RESTRAINT SYSTEM . |
| B2488 | Thumb-Wheel Switch Voltage Out of Range High | CCSM | GO to PINPOINT TEST K . |
| B2521 | Tach Circuit Failure | CCSM | GO to PINPOINT TEST J . |
| B2729 | Cushion Over-Temp Detected | CCSM | GO to PINPOINT TEST L . |
| B2730 | Back Over-Temp Detected | CCSM | GO to PINPOINT TEST L . |
| B2731 | Differential Temperature Fault | CCSM | GO to PINPOINT TEST L . |
| B2792 | Heat Switch Short to Ground | CCSM |
NOTE:
If HEAT is pressed for more than 20 seconds on the climate controlled seat switch, DTC B2792 will set in the CCSM. CLEAR the DTC. If the DTC does not clear, DEPOWER the supplemental restraint system (SRS). Refer to SUPPLEMENTAL RESTRAINT SYSTEM
. DISCONNECT driver seat C327 or passenger seat C315 of the affected seat and CONNECT restraint system diagnostic tool 501-095 to the affected seat connector. CONNECT the battery ground cable. CHECK circuit 1551 (VT/WH) for a fault and REPAIR as needed. If OK, INSTALL a new climate controlled seat switch. Once the repair is complete, DISCONNECT the restraint system diagnostic tool from the seat connector and CONNECT the seat connector of the affected seat. REPOWER the SRS. Refer to SUPPLEMENTAL RESTRAINT SYSTEM
. |
| B2793 | Cool Switch Short to Ground | CCSM |
NOTE:
If COOL is pressed for more than 20 seconds on the climate controlled seat switch, DTC B2793 will set in the CCSM. CLEAR the DTC. If the DTC does not clear, DEPOWER the supplemental restraint system (SRS). Refer to SUPPLEMENTAL RESTRAINT SYSTEM
. DISCONNECT driver seat C327 or passenger seat C315 of the affected seat and CONNECT restraint system diagnostic tool 501-095 to the affected seat connector. CONNECT the battery ground cable. CHECK circuit 1550 (WH/OG) for a fault and REPAIR as needed. If OK, INSTALL a new climate controlled seat switch. Once the repair is complete, DISCONNECT the restraint system diagnostic tool from the seat connector and CONNECT the seat connector of the affected seat. REPOWER the SRS. Refer to SUPPLEMENTAL RESTRAINT SYSTEM
. |
| U2362 | UBP Invalid Data Node ID | CCSM |
NOTE:
DTC U2362 indicates a network concern. The CCSM is not the source of the fault. CLEAR the DTC. If the DTC does not clear, REFER to MODULE COMMUNICATIONS NETWORK
. |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
