Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2005 Lincoln Aviator AWDFACTORY OEM SERVICE PROCEDURE
Anti-Lock Control
- Specifications
- Description And Operation
- Diagnosis And Testing
- Anti-Lock Control
- Notes
- Special Tool(s)
- Principles of Operation
- Inspection and Verification
- Symptom Chart
- Notes
- Connector Circuit Reference
- Primary Brake Pressure Transducer C147
- Brake Pedal Travel Sensor C148
- Active Brake Booster C149
- LH Front Wheel Speed Sensor C150, RH Front Wheel Speed Sensor C160
- LH Rear Wheel Speed Sensor C440, RH Rear Wheel Speed Sensor C426
- Anti-Lock Brake System (ABS) C155
- Steering Wheel Rotation Sensor C226
- Traction Control Switch C280
- Sensor Cluster C3179 (2WD)
- Sensor Cluster C3179 (4WD)
- Pinpoint Test A: No Communication With the Anti-lock Brake System (ABS) Module
- Pinpoint Test B: DTC B1483 - Brake Pedal Input Circuit Failure
- Pinpoint Test C: DTC B1676 - Battery Pack Voltage Out Of Range
- Pinpoint Test D: DTC C1095 -Anti-lock Brake System (ABS) Hydraulic Pump Motor Circuit Failure
- Pinpoint Test E: DTC C1145, DTC C1155, DTC C1165, DTC C1175 - Wheel Speed Sensor Input Circuit Failure
- Pinpoint Test F: DTC C1233, DTC C1234, DTC C1235, DTC C1236 - Wheel Speed Sensor Input Signal Missing
- Pinpoint Test G: DTC C1277 and C1278 - Steering Wheel Angle 1 and 2 Circuit Failure/Faulted
- Pinpoint Test H: DTC C1279, C1280, C1281, C1282, C1516, C1517, C2769, C2770, U1900, U2023 - Sensor Cluster Fault
- Pinpoint Test I: DTC C1285 - Booster Solenoid Circuit Failure
- Pinpoint Test J: DTC C1287 - Brake Booster Pedal Force Switch Circuit Failure
- Pinpoint Test K: DTC C1288 and C1440 - Brake Pressure Transducer Input Circuit Failure
- Pinpoint Test L: DTC C1730 - Reference Voltage Out Of Range (+5 V)
- Pinpoint Test M: DTC C1960 - Driver Brake Apply Circuit Fault
- Pinpoint Test N: DTC B2734, B2736, B2737, B2738, B2740 - Pedal Travel Sensor Fault
- Pinpoint Test O: Stability Assist Cannot Be Disabled
- Pinpoint Test P: DTC C1998 - Module Calibration Not Complete
- Pinpoint Test Q: The Traction Control Switch Indicator Is Never/Always On
- Anti-Lock Control
- Removal And Installation
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
Comes to youSame-day available12-month warranty
Get a Free QuoteNo obligation. See pricing before you book.