2004 Lincoln Navigator RWDFACTORY OEM SERVICE PROCEDURE

Anti-Lock Control DTCS

ANTI-LOCK BRAKE CONTROL DIAGNOSTIC TROUBLE CODE (DTC) LIST

DTC Description Source Action
B1342 ECU is Defective Anti-Lock Brake Control Module CLEAR the DTCs. RETRIEVE the DTCs. If other DTCs are retrieved, REPAIR them. CLEAR the DTCs, and REPEAT the self-test. If DTC B1342 is retrieved, INSTALL a new ABS module. Refer to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE .
B1483 Brake Pedal Input Circuit Failure Anti-Lock Brake Control Module Go To PINPOINT TEST B .
B1676 Battery Pack Voltage Out of Range Anti-Lock Brake Control Module Go To PINPOINT TEST C .
B2477 Module Configuration Failure Anti-Lock Brake Control Module CONFIGURE the anti-lock brake control module. Refer to MODULE CONFIGURATION . CLEAR the DTCs. REPEAT the self-test. If DTC B2477 is retrieved again, INSTALL a new anti-lock brake control module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE . REPEAT the self-test.
C1095 Hydraulic Pump Motor Circuit Failure Anti-Lock Brake Control Module Go To PINPOINT TEST D .
C1145 Speed Wheel Sensor RF Input Circuit Failure Anti-Lock Brake Control Module Go To PINPOINT TEST E .
C1155 Speed Wheel Sensor LF Input Circuit Failure Anti-Lock Brake Control Module Go To PINPOINT TEST E .
C1165 Speed Wheel Sensor RR Input Circuit Failure Anti-Lock Brake Control Module Go To PINPOINT TEST F .
C1175 Speed Wheel Sensor LR Input Circuit Failure Anti-Lock Brake Control Module Go To PINPOINT TEST E .
C1233 Speed Wheel LF Input Signal Missing Anti-Lock Brake Control Module Go To PINPOINT TEST F .
C1234 Speed Wheel RF Input Signal Missing Anti-Lock Brake Control Module Go To PINPOINT TEST F .
C1235 Speed Wheel RR Input Signal Missing Anti-Lock Brake Control Go To PINPOINT TEST F .
C1236 Speed Wheel LR Input Signal Missing Anti-Lock Brake Control Module Go To PINPOINT TEST F .
C2769 Longitudinal Acceleration Sensor Circuit Failure Anti-Lock Brake Control Module INSTALL a new ABS module. Refer to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE . CLEAR the DTCs. REPEAT the self-test.
C2770 Longitudinal Acceleration Sensor Signal Fault Anti-Lock Brake Control Module INSTALL a new ABS module. Refer to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE . CLEAR the DTCs. REPEAT the self-test.
U1009 SCP (J1850) Invalid or Missing Data for Engine Torque ABS CARRY OUT the PCM self-test.
U1027 SCP (J1850) Invalid or Missing Data for Engine RPM ABS CARRY OUT the PCM self-test.
U1262 SCP (J1850) Communication Bus Fault ABS Refer to MODULE COMMUNICATIONS NETWORK .
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.

Rather have a pro handle this?

A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.

Comes to youSame-day available12-month warranty
Get a Free Quote

No obligation. See pricing before you book.