2003 Lincoln Aviator AWDFACTORY OEM SERVICE PROCEDURE

Pinpoint Test D: No Communication With The Lighting Control Module (LCM)

WARNING: This page is about a different car, the 2004 Lincoln Town Car. However, it is still accessible from the selected car via links, so may be relevant.

Test Step 

D1 CHECK CIRCUIT 640 (RD/YE) FOR VOLTAGE 

  • Key in OFF position.
  • Disconnect: LCM C2145a.
  • Key in ON position.
  • Measure the voltage between LCM C2145a pin 17, circuit 640 (RD/YE), harness side and ground.
    Fig 1: Checking Circuit 640 (RD/YE) For Voltage
    G03250293Courtesy of FORD MOTOR CO.
  • Is the voltage greater than 10 volts? 

Result / Action to Take 

Yes 

GO to D2.

No 

REPAIR the circuit. REPEAT the self-test.

Test Step 

D2 CHECK CIRCUIT 964 (DB/LG) FOR VOLTAGE 

  • Key in OFF position.
  • Measure the voltage between LCM C2145b pin 6, circuit 964 (DB/LG), harness side and ground.
    Fig 2: Checking Circuit 964 (DB/LG) For Voltage
    G03250294Courtesy of FORD MOTOR CO.
  • Is the voltage greater than 10 volts? 

Result / Action to Take 

Yes 

GO to D3.

No 

REPAIR the circuit. REPEAT the self-test.

Test Step 

D3 CHECK CIRCUIT 676 (PK/OG) C2145A FOR AN OPEN 

  • Measure the resistance between LCM C2145a pin 23, circuit 676 (PK/OG), harness side and ground.
    Fig 3: Checking Circuit 676 (PK/OG) C2145A For An Open
    G03250295Courtesy of FORD MOTOR CO.
  • Is the resistance less than 5 ohms? 

Result / Action to Take 

Yes 

GO to D4.

No 

REPAIR the circuit. REPEAT the self-test.

Test Step 

D4 CHECK CIRCUIT 676 (PK/OG) C2145C FOR AN OPEN 

  • Key in OFF position.
  • Measure the resistance between LCM C2145c pin 13, circuit 676 (PK/OG), harness side and ground.
    Fig 4: Checking Circuit 676 (PK/OG) C2145C For An Open
    G03250296Courtesy of FORD MOTOR CO.
  • Is the resistance less than 5 ohms? 

Result / Action to Take 

Yes 

GO to D5.

No 

REPAIR the circuit. REPEAT the self-test.

Test Step 

D5 CHECK FOR CORRECT LCM OPERATION 

  • Disconnect all LCM connectors.
  • Check for:
    • corrosion
    • pushed-out pins
  • Connect all LDM connectors and make sure they seat correctly.
  • Operate the system and verify the concern is still present.
  • Is the concern still present? 

Result / Action to Take 

Yes 

INSTALL a new LCM. REFER to MODULE-LIGHTING CONTROL (LCM)  . TEST the system for normal operation.

No 

The system is operating correctly at this time. Concern may have been caused by a loose or corroded connector. CLEAR the DTCs. REPEAT the self-test.

Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.