2000 Lincoln ContinentalFACTORY OEM SERVICE PROCEDURE

Test G: Lighting Control Module (LCM) Does Not Respond To NGS Tester

WARNING: This page is about a different car, the 2001 Lincoln Continental. However, it is still accessible from the selected car via links, so may be relevant.
  1. Turn ignition switch to OFF position. Disconnect Lighting Control Module (LCM) 22-pin harness connector C206 located behind left side of instrument panel, behind headlight switch. Inspect harness connector for loose, damaged or corroded terminals. Repair harness connector as necessary and retest system for normal operation. If harness connector is okay, reconnect harness connector. Connect New Generation Star (NGC) tester to Data Link Connector (DLC) Turn ignition switch to ON position. Perform data link diagnostic procedure. See DATA LINK DIAGNOSTIC TESTΒ  under SELF-DIAGNOSTIC SYSTEM. If NGS tester indicates LCM: NO RESPONSE ON CKT 914 (BUS +), go to next step. If NGS tester indicates LCM: NO RESPONSE ON CKT 914 (BUS -), go to step Β 5 .
  2. Turn ignition switch to OFF position. Disconnect NGS tester. Disconnect LCM harness connector C206. Measure resistance of Tan/Orange wire between terminal No. 2 at LCM harness connector C206 and terminal No. 2 at DLC. See Figure and Fig 1 . If resistance is greater than 5 ohms, go to next step. If resistance is 5 ohms or less, replace LCM.
  3. Disconnect 84-pin harness connector C217 located behind left side of instrument panel. See Figure . Inspect harness connector for loose, damaged or corroded terminals. Repair harness connector as necessary and retest system for normal operation. If harness connector is okay, measure resistance of Tan/Orange wire between terminal No. 55 at harness connector C217 and terminal No. 2 at DLC. See Figure and Figure . If resistance is 5 ohms or less, go to next step. If resistance is greater than 5 ohms, repair open in Tan/Orange wire between harness connector C217 and DLC.
  4. Disconnect 84-pin harness connector C212 located behind left side of instrument panel. See Figure . Inspect harness connector for loose, damaged or corroded terminals. Repair harness connector as necessary and retest system for normal operation. If harness connector is okay, measure resistance of Tan/Orange wire between terminal No. 28 at harness connector C212 and terminal No. 2 at LCM harness connector C206. See Figure and Fig 1 . If resistance is 5 ohms or less, repair open in Tan/Orange wire between female half of harness connector C217 and harness connector C212. If resistance is greater than 5 ohms, repair open in Tan/Orange wire between male half of harness connector C212 and LCM.
  5. Turn ignition switch to OFF position. Disconnect NGS tester. Disconnect LCM 22-pin harness connector C206. Measure resistance of Pink/Light Blue wire between terminal No. 1 at LCM harness connector C206 and terminal No. 10 at DLC. See Figure and Fig 1 . If resistance is greater than 5 ohms, go to next step. If resistance is 5 ohms or less, replace LCM.
  6. Disconnect 84-pin harness connector C217 located behind left side of instrument panel. See Figure . Inspect harness connector for loose, damaged or corroded terminals. Repair harness connector as necessary and retest system for normal operation. If harness connector is okay, measure resistance of Pink/Light Blue wire between terminal No. 79 at harness connector C217 and terminal No. 10 at DLC. See Figure and Figure . If resistance is 5 ohms or less, go to next step. If resistance is greater than 5 ohms, repair open in Pink/Light Blue wire between harness connector C217 and DLC.
  7. Disconnect 84-pin harness connector C212 located behind left side of instrument panel. See Figure . Inspect harness connector for loose, damaged or corroded terminals. Repair harness connector as necessary and retest system for normal operation. If harness connector is okay, measure resistance of Pink/Light Blue wire between terminal No. 29 at harness connector C212 and terminal No. 1 at LCM harness connector C206. See Figure and Fig 1 . If resistance is 5 ohms or less, repair open in Pink/Light Blue wire between female half of harness connector C217 and harness connector C212. If resistance is greater than 5 ohms, repair open in Pink/Light Blue wire between male half of harness connector C212 and LCM.
Fig 1: Identifying LCM Harness Connector C206 Terminals
G97D28772Courtesy of FORD MOTOR CO.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.