Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2021 Lexus ES 250 BaseFACTORY OEM SERVICE PROCEDURE
Engine Control System (A25A-FKS) - Diagnostic Codes (08 Of 12)
- SFI System
- DTC P0627-12: Fuel Pump "A" Control Circuit Short to Battery [08/2021 - ]
- DTC P0627-14: Fuel Pump "A" Control Circuit Short to Ground or Open [08/2020 - 08/2021]
- DTC P0627-14: Fuel Pump "A" Control Circuit Short to Ground or Open [08/2021 - ]
- DTC P062F-44: Internal Control Module EEPROM Data Memory Failure [08/2020 - 08/2021]
- DTC P062F-44: Internal Control Module EEPROM Data Memory Failure [08/2021 - ]
- DTC P0630-51: VIN Not Programmed [08/2020 - 08/2021]
- DTC P0630-51: VIN Not Programmed [08/2021 - ]
- DTC P064A-49: Fuel Pump Control Module Internal Electronic Failure [08/2020 - 08/2021]
- DTC P064A-49: Fuel Pump Control Module Internal Electronic Failure [08/2021 - ]
- DTC P0657-14: Actuator Supply Voltage "A" Circuit Short to Ground or Open [08/2020 - 08/2021]
- DTC P0657-14: Actuator Supply Voltage "A" Circuit Short to Ground or Open [08/2021 - ]
- DTC P0657-9E: Actuator Supply Voltage "A" Stuck On [08/2020 - 08/2021]
- DTC P0657-9E: Actuator Supply Voltage "A" Stuck On [08/2021 - ]
- DTC P06AB-11: Control Module Internal Temperature Sensor "B" Circuit Short to Ground; DTC P06AB-15: Control Module Internal Temperature Sensor "B" Circuit Short to Battery or Open [08/2020 - 08/2021]
- DTC P06AB-11: Control Module Internal Temperature Sensor "B" Circuit Short to Ground; DTC P06AB-15: Control Module Internal Temperature Sensor "B" Circuit Short to Battery or Open [08/2021 - ]
- DTC P06DA-13: Engine Oil Pressure Control Circuit Open [08/2020 - 08/2021]
- DTC P06DA-13: Engine Oil Pressure Control Circuit Open [08/2021 - ]
- DTC P0703-12: Brake Switch "B" Circuit Short to Battery [08/2020 - 08/2021]
- DTC P0703-12: Brake Switch "B" Circuit Short to Battery [08/2021 - ]
- DTC P0705-13: Transmission Range Sensor "A" Circuit Open; DTC P0705-62: Transmission Range Sensor "A" Signal Compare Failure [08/2020 - 08/2021]
- DTC P0705-13: Transmission Range Sensor "A" Circuit Open; DTC P0705-62: Transmission Range Sensor "A" Signal Compare Failure [08/2021 - ]
- DTC P106A-62: Evaporative Emission System Pressure / Intake Air Pressure Signal Compare Failure; DTC P106C-62: Evaporative Emission System Pressure/Barometric Pressure Signal Compare Failure [08/2020 - 08/2021]
- DTC P106A-62: Evaporative Emission System Pressure / Intake Air Pressure Signal Compare Failure; DTC P106C-62: Evaporative Emission System Pressure/Barometric Pressure Signal Compare Failure [08/2021 - 07/2023]
- DTC P106A-62: Evaporative Emission System Pressure / Intake Air Pressure Signal Compare Failure; DTC P106C-62: Evaporative Emission System Pressure/Barometric Pressure Signal Compare Failure [07/2023 - ]
- DTC P107A-11: Fuel Rail Pressure Sensor (Low) Circuit Short to Ground [08/2020 - 08/2021]
- DTC P107A-11: Fuel Rail Pressure Sensor (Low) Circuit Short to Ground [08/2021 - ]
- DTC P107A-15: Fuel Rail Pressure Sensor (Low) Circuit Short to Battery or Open [08/2020 - 08/2021]
- DTC P107A-15: Fuel Rail Pressure Sensor (Low) Circuit Short to Battery or Open [08/2021 - ]
- DTC P107A-2A: Fuel Rail Pressure Sensor (Low) Signal Stuck in Range; DTC P107A-64: Fuel Rail Pressure Sensor (Low) Signal Plausibility Failure [08/2020 - 08/2021]
- DTC P107A-2A: Fuel Rail Pressure Sensor (Low) Signal Stuck in Range; DTC P107A-64: Fuel Rail Pressure Sensor (Low) Signal Plausibility Failure [08/2021 - ]
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
