Customize Parameters

HINT: 

The items in the table below can be customized.

1. Connect the Techstream to the DLC3.
2. Turn the power switch on (IG).
3. Turn the Techstream on.
4. Enter the following menus: Customize Setting.
5. Select the setting by referring to the table below.
   SMART KEY/ACCESS
   
   

   Tester Display	Default	Content	Setting
   Ignition Available Area	All	Function that switches the entry ignition detection area.	Front or All*
   Park Wait Time	2.5 s	Function that sets waiting time to permit opening the door after the door is locked with the entry lock function.	0.5 s, 1.5 s, 2.5 s or 5 s
   Trunk Open Mode	ON	Function to permit opening the luggage compartment door.	ON or OFF
   Door Unlock Mode	Driver	Function that chooses the doors to be operated by entry unlock operation	All or Driver
   Touch Activation Over Threshold	Active	The function that limits the consecutive entry lock operation to only 2 times can be changed between Active and Not Active. When in Not Active mode, there is no limit for the number of times that the consecutive entry lock operation can be performed.	Active or Not Active

   *: Weak radio waves will still be emitted from oscillators other than the front oscillator even when the "Front" customize setting is selected.

   WARNING
   
   

   Tester Display	Default	Content	Setting
   Key Low Battery Warning	ON	Function that warns the driver that the key battery is low.	ON or OFF

1. Check that the power source mode is OFF and the LED on the key is not blinking. Press the lock switch and one of the other switches on the key at the same time for approximately 5 seconds while the key is in the detection area.
   • Driver door unlock default setting:

     When the switches are pressed and held for 5 seconds, the entry door unlock mode changes to the mode that is not currently selected.

   NOTE: After pressing and holding the switches for 5 seconds, wait 5 seconds before performing the same procedure again.
   • Driver door unlock mode:

     When the driver door touch sensor is touched, only the driver door unlocks. When another touch sensor is touched, all doors unlock.

   • All door unlock mode:

     When any touch sensor is touched, all doors unlock.

2. The certification ECU (smart key ECU assembly) receives this signal from the door control receiver and changes the smart access system with push-button start to the entry unlock mode.
3. The certification ECU (smart key ECU assembly) sounds the wireless door lock buzzer and combination meter buzzer to inform the user that the mode has been switched.

   Mode	Wireless Door Lock Buzzer	Combination Meter Buzzer
   Driver Door (Default)	Sounds 3 times	Sounds once
   All Doors (Customized)	Sounds 2 times	Sounds once

   HINT: 

   The procedure only changes the entry unlock mode of the smart access system with push-button start. It does not switch the unlocking of the wireless door lock control.

HINT: 

To start the hybrid control system while the smart access system with push-button start is disabled, follow the procedure for when the key battery is low. Refer to SYSTEM DESCRIPTION .

The electrical key cancel operation disables the following functions:

• Entry Unlock/Lock
• Entry Hybrid Control System Start
• Entry Luggage Compartment Door Open
• Electrical Key Lock-in Prevention
• Warning

1. The operation procedure is as follows:

   Precondition:

   Power switch off, driver door closed and unlocked.

   1. Push the unlock switch of the key once.
   2. Open the driver door within 5 seconds.
   3. Push the unlock switch of the key twice within 5 seconds.
   4. Close and open the driver door twice within 30 seconds.

      (Driver door: Close → Open → Close → Open)

   5. Push the unlock switch of the key twice within 5 seconds.
   6. Close and open the driver door within 30 seconds.

      (Driver door: Close → Open)

   7. Close the driver door within 5 seconds.

      When electrical key cancel is activated, the wireless door lock buzzer sounds twice.

      To return to the original condition, perform the procedure again. When the original condition is returned, the wireless door lock buzzer sounds once.